Reddit reviews DGC PRODUCTS i-Socket Intelligent Autoswitch with ports for Power Tool and Vacuum; PATENTED TECHNOLOGY delays Vacuum Turn-On/Off to Prevent Circuit Overload, Eliminating Circuit Breaker Tripping
We found 11 Reddit comments about DGC PRODUCTS i-Socket Intelligent Autoswitch with ports for Power Tool and Vacuum; PATENTED TECHNOLOGY delays Vacuum Turn-On/Off to Prevent Circuit Overload, Eliminating Circuit Breaker Tripping. Here are the top ones, ranked by their Reddit score.
HOW IT WORKS. Patented automatic vacuum switch uses an on-Board Micro-Controller to monitor and control current when two large motors try to power-up at the same time. Prevents circuit overload by automatically delays vacuum turn-off by 7 seconds.EFFECTIVENESS. Runs the vacuum only when you are working so you save time and electricity. Reduces airborne toxin that can lead to many health problems. Reduces work area noise by running the vacuum only when you use your tool.BEST FOR medium duty workloads in the home workshop and on the job site. It’s actuation threshold of about 0.7 amps (85 watts at 120V) makes it perfectly suited for most Miter Saws, Table Saws, Power Sanders and Routers and extends the life of your vacuum.ELECTRONICS. A software embedded micro-controller controls the in rush of current when the motor starts up to help eliminate overload of the circuit. Once the tool stops, it provides power to the vacuum for seven seconds to clean out the inlet pipe.TECHNICAL SPECS. Case: Durable UL-rated 94V, ABS plastic; Outlet required: Standard 15 Amp, 120 VAC, 60 Hz outlet; Power rating: 15 Amp, 120 VAC, 60 Hz; Input connection: 3 prong (grounded) male; Tool outlet connections: 2 or 3 prong plugs
https://www.amazon.com/DGC-PRODUCTS-Intelligent-Autoswitch-Eliminating/dp/B005ELWUWG
Not the one I have but something similar
Here you go.
link
It’s more fun to make your own. Also, the switch is cheaper and probably less prone to failure.
http://www.amazon.com/i-Socket-IS110M-DGC-PRODUCTS-Autoswitch/dp/B005ELWUWG/ref=pd_cp_hi_0
proportion based control sounds like its going to be cost prohibitive, only other idea i can think of is something like this. its designed for woodshops, when you turn on a tool it will also switch on your vacuum, since its designed for high power tools it might not turn on for a small load if you have just a machine or two on in your cluster but if everything gets running it can bring your fans on, still AC based though. this particular one looks like it has some quality issues so this exact unit might not be the best but i think you'd understand the idea of it.
Yes! I know exactly what I wanna do. acquire a cheap shop vacuum and add this neat little device. http://amzn.com/B005ELWUWG basically you plug your saw and dust collection into it or in my case vacuum and when I turn my saw on this turns the vacuum on and leaves it on for a few seconds after I am done using the saw.
I think this is the item you're asking about but on a larger scale?
https://www.amazon.com/DGC-PRODUCTS-IS110M-i-Socket-Autoswitch/dp/B005ELWUWG/ref=pd_ybh_a_17?_encoding=UTF8&psc=1&refRID=P4YQY28K22KYZ01G1V7T
If anyone is looking for a prebuilt solution, there is the DGC Products i-Socket Autoswitch https://www.amazon.com/dp/B005ELWUWG/ref=cm_sw_r_taa_x4IrybDSFY6M0
There are products that do that.
https://www.amazon.com/Current-Sensing-Normally-Adjustable-SZC23-NO-AL-CH/dp/B07N1P6TWL
https://www.amazon.com/DGC-PRODUCTS-Intelligent-Autoswitch-Eliminating/dp/B005ELWUWG/
Nice find, but I'm thinking by his description it would be more likely the frequently bought together recommendation of this device
You could also consider a plug in booster on a switch that activates when the microwave draws power, although you would need to make sure the phantom / always on draw of the microwave is sufficient. We use these often in woodworking to activate a vacuum / dust collector when we turn on a tool. https://www.amazon.com/DGC-PRODUCTS-IS110M-i-Socket-Autoswitch/dp/B005ELWUWG/ref=sr_1_1?ie=UTF8&qid=1473977713&sr=8-1&keywords=power+tool+vacuum+switch