Reddit Reddit reviews Dryer Dock The Original Dryer Vent Quick Release - Two-Piece Dryer Hose Quick-Connect, Twist & Lock Tight, Fits 4 Inch Tubes

We found 3 Reddit comments about Dryer Dock The Original Dryer Vent Quick Release - Two-Piece Dryer Hose Quick-Connect, Twist & Lock Tight, Fits 4 Inch Tubes. Here are the top ones, ranked by their Reddit score.

Parts & Accessories
Clothes Dryer Replacement Parts
Clothes Dryer Replacement Vents
Appliances
Dryer Dock The Original Dryer Vent Quick Release - Two-Piece Dryer Hose Quick-Connect, Twist & Lock Tight, Fits 4 Inch Tubes
DryerDock Quick-Connect - It is the easiest way to connect your dryer's vent to your house vent. This unique solution is easy to install, looks great when installed, saves space behind the dryer, and makes maintenance a snap. Fits 4" tubes with a 6" flangeEasy Maintenance - Dryer Dock is a two-piece “Quick Release System” that enables quick access to your dryer vent hose and vent pipe, allowing for easy removal and cleaning. Keeping the vent clean, saves energy, and prevents dryer firesEliminates Environmental Intrusion - Made of rigid ABS plastic and fastens together with a slight twist, the rigid design keeps the hose securely in place, eliminates air drafts, pest intrusion, saves energy, wear and tear on both dryer and clothesPrevents Fires - According to the National Fire Protection Association, dryer vent fires are the number one cause of household fires, nearly 17,000 home dryer fires are reported each year, causing around 51 deaths, 380 injuries, and $236 million in property lossThe Original Dryer Dock - Patented under USP # 6,131,958. Dryer Dock is the “Gold Standard” of quick release in the industry for home and commercial applications, it is installed in more than 500,000 homes, factories, and offices. Proudly made in the USA
Check price on Amazon

3 Reddit comments about Dryer Dock The Original Dryer Vent Quick Release - Two-Piece Dryer Hose Quick-Connect, Twist & Lock Tight, Fits 4 Inch Tubes:

u/checkitoutmyfriend · 4 pointsr/BurningMan

One could set another bucket at a higher level than the FIgJam cooler. Then either use a valve to refill or an aquarium float in the FJ to maintain level. But a FJ cooler will run for4-6hrs. So refilling it is not that big of deal really. (Mine is used for grey water evap so I had a second bucket a valve setup.)

100ah deep cycle batts are the way to go. Don't cheap out and not go deep cycle. (FigJam himself uses a Wal-Mart $80 Deepcycle) Solar panels for other than trickle charge to the batt are labor intensive to keep clean and lose efficiency for the same. So they are good to keep the batt topped off, but not to rely in it running you gear. Unless you are really into solar and know what to expect. It's not all plug and play.

To duct into the tent depends on if you want to cut a hole or not. Some use a dryer duct wall vent. Its glued or screwed the the tent wall. Might have to make a ring to sandwich the material. I would use semi rigid duct as it is stiffer and restricts air flow less then the spring type ducts. Wrap with a towel or foil bubble wrap for some insulation. 5" with one end made to a square fits tightly around the PC fan frame. Problem is 5" is an oddball size for dryer vet fittings that are 4 or 6". Go 6" if you need to chose. less air restriction that way.

If you don't want to cut a hole than you need to stick through the door and seal it up the best you can with a towel or similar.

Be sure to have a vent in the ten to allow air to escape... Swamp are air in - air out cooling.

Here is a link for pumps, fans, media, etc.

If anyone has questions, let me know. I've built a number of them in various forms. Storage bin cooler last year. Trash can version this year. But I use them for grey water evap. A lot less messy then a evap pond or air driven evap.

u/jds580s · 3 pointsr/ChineseLaserCutters

You could use that along with some aluminum tape to seal it to the back of the cutter.

I use this blower:
attwood Quiet Blower Water Resistant (White, 4-Inch) https://www.amazon.com/dp/B003EX02DA/ref=cm_sw_r_cp_api_3L18BbTB6G1FB

Along with this vent hose:
White Flexible Pvc Vinyl Vent Duct Hose, 4 in. x 20 ft. https://www.amazon.com/dp/B01G198P5A/ref=cm_sw_r_cp_api_4R18BbNJ19ANP

These clamps:
Cambridge Tension Clamps, 2 Pk, Zinc Plated Steel https://www.amazon.com/dp/B07737XRRH/ref=cm_sw_r_cp_api_SS18Bb12827MZ

And this quick disconnect:
Dryer Dock Dryer Vent 6" for 4" Tubes, White https://www.amazon.com/dp/B0028BAAWW/ref=cm_sw_r_cp_api_4T18BbV6CJ1TW

If you put the blower near the window it will keep negative pressure upstream which helps put less smoke into the room.

I don’t exhaust out a window, but something like this might do the trick for you:
Window Dryer Vent (Adjusts 24 Inch Through 36 Inch) by Vent Works https://www.amazon.com/dp/B01M17V4CO/ref=cm_sw_r_cp_api_AW18BbDW0592D
Though there may be cheaper or better DIY options for that part.

u/SchnaapsIdee · 2 pointsr/HomeImprovement

Sounds like you already tried a short metal connector but said it wouldn't fit. I'm surprised that you couldn't get the ruffled side in enough give you something to grip. Sometimes you need to get some pliers and manipulate the edges to get it to cram in.

But anyway, Maybe try something like this. https://www.amazon.com/Dryer-Dock-Vent-Tubes-White/dp/B0028BAAWW

Even if the white plastic part doesn't fit in your hole you could saw that part off with a coping saw or something so it sits flush against the hole and attach it stud/drywall around the hole.