Reddit reviews Fluke 323 True-RMS Clamp Meter
We found 7 Reddit comments about Fluke 323 True-RMS Clamp Meter. Here are the top ones, ranked by their Reddit score.
Digital clamp meter measures ac current to 400 amp, AC and DC voltage to 600 v, and resistance to 4 kilohms. Does not measure dc currentTrue RMS sensing meter provides accurate readings when measuring linear or non linear loads, regardless of waveformJaw opening measures current in a conductor upto 30 millimeter without touching or interrupting the circuit. Resistance accuracy: 1.0% ± 5 digitsAudible continuity sensor confirms that the circuit conducts electricityMeets IEC safety standard 61010 1, and is rated for CAT IV installations to 300V and CAT III installations to 600V
Hi there, I have experienced something like this twice. If you are sure that everything is in order and there are no obvious billing errors, I strongly suggest you get a clamp ammeter like this:
https://www.amazon.com/Fluke-323-True-RMS-Clamp-Meter/dp/B00AQKIEXY/ref=sr_1_7?ie=UTF8&qid=1500148644&sr=8-7&keywords=power+meter+clamp
Power all circuits down in your house, switch everything off. Put the clamp over the inlet cable and see if there is power running through, if there is, something is broken or wrong, call an electrician. If not, then power each device or item up, one at a time and look for things that are drawing excessive electricity.
I had a beer fridge fail one day, but it did not die, the motor decided to run 24/7 somehow not freeze the beer, but just keep drawing. I've also dealt with a faulty fluorescent basalt that was drawing way more power than it should have been, even while seemingly working fine. In both cases, there was a sudden cost spike and my utilisation increased significantly.
Clamp meters allow you to measure the power without exposing the cables, so this is safest if you're not electrically savvy. I would also suggest a device like this:
https://www.amazon.com/Excelvan-Display-Voltage-Electricity-Monitor/dp/B00E1E1XA2/ref=sr_1_2?ie=UTF8&qid=1500148919&sr=8-2-spons&keywords=power+meter+plug&psc=1
You can use this occasionally to test and check equipment or appliances are not over drawing. Some of these plugs have the ability to state the cost of the electricity being used, a useful tool to gauge the cost of running or owning appliances.
What about this one? http://www.amazon.com/gp/product/B00AQKIEXY?psc=1&redirect=true&ref_=ox_sc_act_title_1&smid=ATVPDKIKX0DER
These circuits are located in event halls. The events are pretty small so we only risk the 20amp circuits but I like to think a few steps ahead to avoid power loss in the middle of a tournament.
The biggest issue is computers. Most of the lower end ones are not a problem but when you have 1k watt to 1.5k watt power supplies the amps add up quick. I figured if I was able to monitor the power I could proactively make sure we are not getting close to tripping circuits.
Do you know if meters such as this work accurately? Do you think it would work for what I am trying to do even if I have to manually go up to it and test it? https://www.amazon.com/Fluke-323-True-RMS-Clamp-Meter/dp/B00AQKIEXY/
A nice fancy multimeter perhaps?
https://www.amazon.com/Fluke-323-True-RMS-Clamp-Meter/dp/B00AQKIEXY?ref_=ast_sto_dp
https://www.amazon.com/dp/B07MXDW677/ref=sspa_dk_detail_0?psc=1
https://www.amazon.com/Fluke-323-True-RMS-Clamp-Meter/dp/B00AQKIEXY/ref=sr_1_3?crid=1MAZW8VU0SD6R&keywords=fluke+clamp+multimeter&qid=1556112802&s=industrial&sprefix=FLuke+clamp%2Cindustrial%2C196&sr=1-3
Two options - use the kW rating on the name plate or buy a [clamp meter] ( http://www.amazon.com/Fluke-323-True-RMS-Clamp-Meter/dp/B00AQKIEXY) which goes completely around the wiring and measures how many amps you're actually using at that moment. Amps multiplied by voltage equals watts. Watts multiplied by 1,000 equals kilowatts.
Edit: learn2math.
So you just want a current meter?
[Fluke 323 True-RMS Clamp Meter ~$100 on amazon](
https://smile.amazon.com/dp/B00AQKIEXY/ref=cm_sw_r_cp_dp_T2_pTavzbJDCH1BV)