Reddit reviews Oatey GIDDS-173390 43539 Replacement Flange Forcast Iron, 4-Inch, PVC

We found 8 Reddit comments about Oatey GIDDS-173390 43539 Replacement Flange Forcast Iron, 4-Inch, PVC. Here are the top ones, ranked by their Reddit score.

This PVC plastic compression closet flange is a replacement for a cast-iron flange. It fits into 4-inch pipes with 3-inch stainless steel bolts.Easily fits and this is easy to installMade in United StatesReplaces broken cast iron closet flangesInstalls easily without toolsNo need to tear up existing floorSmooth unrestricted flow designReplaces broken cast iron closet flangesInstalls easily without toolsNo need to tear up existing floorSmooth unrestricted flow design

Check price on Amazon

8 Reddit comments about Oatey GIDDS-173390 43539 Replacement Flange Forcast Iron, 4-Inch, PVC:

u/my_cat_joe · 9 pointsr/HomeImprovement

That soil pipe is lead. It's pretty common that they aren't attached to anything, but it's not going to go anywhere either. You need one of these. They come in 4 inch, and (for really old houses) 3 inch sizes. You set that in your soil pipe, expand it to fit snug, attach that to the floor (which is the tricky bit because you may need drill through the tile with a diamond bit), then attach the toilet to the new flange with a pair of hand-tightened toilet bolts. A wax ring goes between the new flange and the toilet. I hope this helps!

Also, if the lead soil pipe is not perfectly round or flush, you can gently hammer it into shape. It's pretty malleable once you start working it.

u/Cane_Skretteburg · 7 pointsr/Plumbing

here you go

u/Saucy6 · 6 pointsr/HomeImprovement

Cast iron I'm assuming? You might be able to pop it off and go with an insert flange:

https://www.thisoldhouse.com/how-to/how-to-repair-cast-iron-toilet-flange

https://www.amazon.com/Oatey-43539-Flange-Replacement-4-Inch/dp/B000DZHDQG

u/distantreplay · 2 pointsr/HomeImprovement

HD was incorrect.
You need one of these:
https://www.amazon.com/Oatey-43539-Flange-Replacement-4-Inch/dp/B000DZHDQG

u/NPC3 · 2 pointsr/Plumbing

This is the part

u/nothingoldcnstay · 2 pointsr/DIY

Find a pvc flange, cut it as needed to fit, seal with epoxy. Couldn't be any worse than before.

Oatey 43539 PVC Cast Iron Flange Replacement, 4-Inch https://www.amazon.com/dp/B000DZHDQG/ref=cm_sw_r_cp_apa_ujofAbN4FDQ56

u/CatsAreTasty · 1 pointr/HomeImprovement

You can pull that flange off and replace it with one of these. When you remove the old flange, patch the hole by inserting two pieces of 2x4 through the hole, deck screw them from above and then screw a piece of plywood to the 2x4s. Push the new flange into the pipe and secure it with screws to the plywood patch.

u/pittsburghtech · 1 pointr/IAmA

I have a pittsburgh toilet in the basement. The cast iron flange cracked (may or may not have been my fault). I chipped out the old flange and got a Repair Flange and a 4" no hub. The no hub was needed because a cast iron 90 comes directly to the floor line, so there is a hub there. Now I ordered two different no hubs, and they both fit, however, there is absolutely NO way the PVC pipe was going to fit in the no hub inside that 90 hub. So, I ended up just using the Repair Flange and expanding the rubber to meet the no hub, without the PVC pipe. Do you find any issues with this?

Thanks!