Reddit reviews Orzly OnePlus 6 Screen Protectors, Twin Pack of Pro-Fit (Full Coverage) Tempered Glass Screen Protector for Oneplus6 (Case Compatible)
We found 4 Reddit comments about Orzly OnePlus 6 Screen Protectors, Twin Pack of Pro-Fit (Full Coverage) Tempered Glass Screen Protector for Oneplus6 (Case Compatible). Here are the top ones, ranked by their Reddit score.
Orzly Pro-Fit technology offers all round protection for your phone's curved screen against surface damage from day to day use, now available in a great value twin pack.Designed with 99.9% transparency to allow an optimal, natural viewing experience while also featuring while additional layers of plastic underlay & overlay ensure increased durability of the screen protector during daily use.ATTENTION!!: The OnePlus 6 has an extremely curved screen edge so you may find on installation, that a small area of the screen protector will trap some air beneath it. This is unavoidable and is the only way to get a full coverage solution. The nature of the curved screen also means that the black frame portion cannot be made any thinner than they are, and may block a tiny proportion of your screen from view depending on your placement during installation.In order to ensure the Pro-Fit Screen Protector is compatible with Orzly cases, it has been designed to leave a little room around the phone's edges.OnePlus 6 [Case Compatible] Screen Protector - PLEASE NOTE: The Pro-Fit Glass Screen Protector is designed to work with Orzly Cases for the OnePlus 6. We cannot however guarantee its compatibility with cases from other manufacturers.
I am using this tempered glass from Orzly. I've tried the Mr Shield and it went too far out to the edge of the screen making it pull up on most of my cases. I'm using the Orzly with the UAG plasma case and works very well.
https://www.amazon.com/Orzly-Protectors-Coverage-Protector-Compatible/dp/B07D4NZXP5/ref=mp_s_a_1_1?ie=UTF8&qid=1538656514&sr=8-1&pi=AC_SX236_SY340_FMwebp_QL65&keywords=orzly+oneplus+6&dpPl=1&dpID=41AOfSjDKyL&ref=plSrch
UAG plasma:
https://www.amazon.com/URBAN-ARMOR-GEAR-Feather-Light-Military/dp/B07F91STBN/ref=mp_s_a_1_1?ie=UTF8&qid=1538656645&sr=8-1&pi=AC_SX236_SY340_FMwebp_QL65&keywords=uag+oneplus+6
The two I see getting recommend the most around the sub since the op6 tempered glass protector went out of stock are:
https://www.amazon.com/gp/product/B07JYL9RLK/ref=ppx_yo_dt_b_asin_title_o01_s00?ie=UTF8&psc=1
https://www.amazon.com/gp/product/B07D4NZXP5/ref=ppx_yo_dt_b_asin_title_o02_s00?ie=UTF8&psc=1
Due to the curved edge of the screen, it's hard to install them without any air bubbles but they provide better protection. I recommend using the one that came pre-installed until it gets damaged
EDIT: additionally glass screen protectors could be incompatible with your case which is why I was asking
I've tried over ten different screen protectors on the OP6. The two I highly recommend
https://www.amazon.com/gp/product/B07JYL9RLK/ref=ppx_yo_dt_b_asin_title_o01_s00?ie=UTF8&psc=1
https://www.amazon.com/gp/product/B07D4NZXP5/ref=ppx_yo_dt_b_asin_title_o02_s00?ie=UTF8&psc=1
The first protector listed has a guide which helps. Additionally, it's easier to align in general since the notch section has precise cut outs for the camera.
The second protector (Orzly) I've also had great results with.
It's important to remember that the most important part of installing a screen protector is the preparation. You will be hard pressed to find any protector (that isn't manipulated reviews) with five stars.
If you have but one spec of dust on the screen when you install it then you will not be satisfied. Clean the screen and your hands, and then do it again and again.
Make sure you have compressed air, and blow it off. Wait a little bit, if no obvious particles manage to settle back down, give it one more quick blow and apply. For most people, especially pet owners, the best place to install is in your bathroom. Prior to installation, clean your bathroom thoroughly, remove all rugs, and some people like to steam it up with their shower.
I really like the installation guide for the first protector, and the fact that the notch section is not just one cut out. I was using the Orzly previously. No complaints whatsoever about the Orzly one either. Both installed perfectly, and the only difference is the installation bracket with the first one is pretty nice.
TLDR: Most tempered glass protectors are sufficient. Generally, most problems are from the installer not the protector.
Just buy any substandard 9H tempered glass but if you buy a better case this probably wouldnt be needed. But if you do want a good one this one should be ideal:
https://www.amazon.co.uk/ORZLY®-Protectors-Tempered-Protector-Compatible/dp/B07D4NZXP5/ref=sr_1_4?ie=UTF8&qid=1527525933&sr=8-4&keywords=oneplus+6+tempered