Reddit Reddit reviews RunCam Split 3 Parent (US-SWIFTMINI-BL-L25-N)

We found 1 Reddit comments about RunCam Split 3 Parent (US-SWIFTMINI-BL-L25-N). Here are the top ones, ranked by their Reddit score.

Electronics
Security & Surveillance Equipment
Security & Surveillance Accessories
Surveillance Camera Lenses
RunCam Split 3 Parent (US-SWIFTMINI-BL-L25-N)
22.3mm * 22mm * 27mm, Weight 12g, compatible with small frame FPV Racing Drone600TVL, IR Blocked, 5D-OSD menu cable, with 2 kinds of bracketWide Voltage: DC 5 to 36V (2S-5S battery)2.5mm Lens, FOV 130°It is suitable for fixed-wing aircraft and Multirotor like QAV250, which are highly required in voltage and weight.
Check price on Amazon

1 Reddit comment about RunCam Split 3 Parent (US-SWIFTMINI-BL-L25-N):

u/Technolosophy · 1 pointr/Multicopter

Sorry for the wall of text. Attempted to submit this as it's own topic but I guess it never got approved.

So I recently just got all the parts for my first quad. I've been doing fairly well with the soldering and have been watching a lot of youtube videos regarding how to wire it up, but I'm still having issues.

Full parts list:

  • Frame: Realacc x210
  • FC: Flip32 Omnibus F3 AIO
  • PDB: Matek XT60(included w/ frame)
  • VTx- Eachine Tx801
  • FPV cam: Eachine 1000TVL
  • Receiver: FrSky XSR
  • ESCs: Racerstar RS30A
  • Motors: Racerstar 2205 2300kv

    FC Wiring Diagram: http://www.dronetrest.com/uploads/db5290/original/2X/6/673c43bd58214a6232f858a7d22ff07add0ff1da.png

    To my understanding, everything I've done so far should be OK-

    I have the ESCs wired to the PDB- two grounds per ESC, one voltage per ESC, and one signal wire going to the motor signal port on the FC.

    I have the 12v voltage regulator on the PDB powering the VTX, with the signal wire going to the Video out pin on the FC.

    I have the main voltage straight from the XT60 going to the Ground and VBAT pins on the FC.

    I have the receiver entirely wired to the FC- 3 wires above the motor, with one going to the TX pin next to the RAM pin.

    I also have the camera entirely hooked up to the FC, in the 3 pins above where I have my VTX wired.

    I have the 5v pin and the bottom leftmost RAM pin wired together to provide 5v power to the camera.

    Here's the issues I'm running into:

    1- Don't know which wires to cross from the motors to the ESCs to reverse direction ( Would rather not rely on software to configure direction)

    2- When I plug in a battery to test things out, I get a video signal to my FPV goggles but it's just a black screen. No actual video. When I tested them and hooked them up directly to the PDB and the signal wires to each other, it worked fine, but I would rather not do that as it won't give me an OSD.

    3- After wiring the RAM & 5v pins together to provide power to the camera, the FC won't power on ( Probably incidentally causing issue 2).

    4- How the hell do I mount a camera on this frame?????? Did I get the wrong type? Would this be a better bet? Or slightly cheaper? How do I actually mount these? There's no mounting holes on the bottom of the frame.

    4 subsection 1- I've attempted to resolve this issue on my own- Found a model on Thingiverse and printed it, but just wasn't able to get good tolerances, even after a significant amount of sanding. Model in question. Second attempt. Third attempt, no place to mount.


    Any and all help or advice is extremely appreciated.