Reddit reviews UCreate Foam Board, White, 22" x 28", 5 Sheets

Hello all, in a previous post made yesterday, I had replied with a picture of a drawer of my Alex 9 unit and received a few of inquiries about how I made my drawer organizers. So, I decided to try my best to tell you how I did it. I apologize I wasn't able to make a complete step by step with a ton of photos, but this process was done over a year ago, and I wasn't really planning on doing it again since I finished!


Materials Needed:

Ruler

X-acto Knife

-I would recommend some extra blades as well-

--Foam Board (the more the merrier)--

Flathead Pins

--Contact Paper--


-The blades become dull fairly quickly, I think I used about four during the process-

--I was able to get a piece for $.99 at Michael’s on sale

---I decided to wrap each piece with contact paper because it makes it very easy to clean. In my actual vanity, I used fabric and it has gotten dirty and damaged and I 100% don't recommend it--


Template Materials:

Copy Paper or Grid Paper

Ruler

Actual makeup products


Steps:

1. I first made templates for each drawer. I found using grid paper to design the setup made it very easy, each block was marked as an inch. Using the actual product dimensions I was easily able to map out what could possibly go in each location. It’s nice to know that the height of a standard sheet of copy paper is the width of the drawers! Also, to note, I made sure to give a little space on each side of the product to give it some wiggle room. (The dimension of each drawer is 11.5"x20.5")
   
   
2. I then used normal copy paper to make a full-size map of each drawer. Then using that I transferred it onto the foam board. Measure twice and cut once.
   
   
3. Using a straight edge, I was able to make cuts of each segment. It's easiest to first cut the width of the product and then afterwards cut the height of each compartment making sure they all have a uniform width and height.
   
   
4. After each piece has been cut, I went ahead and wrapped every piece with white contact paper. Contact paper has a sticky back that easily allows it to adhere. Also, the back has its own grid so it was easy!
   
   
5. Once each piece was ready to go ahead and assemble, I made a new template. This one was to make a uniform depth of each compartment (my smaller compacts all had about 3/4 of an inch between each and larger had about 1 inch) A B. This also made it very easy to ensure I had a perfect right angle.
   
   
6. I decided to use flathead pins to connect everything together. I've seen previous YouTube tutorials that used hot glue, but that can be messy and difficult to work with. Also, if you ever need to redo something, you don't destroy what you had done. I used two pins on each side which really anchors the part. I will note, the tips of my index fingers went numb from doing this so much, but the feeling came back…eventually
   
   
7. Enjoy!
   
   
   Some other things to note:
   
   In my palette drawer, I created L shaped panels to allow for the palette to be better seen
   
   I also purchased from byAlegory a liquid lipstick and lipstick organizers to build around
   
   In my lipstick drawer, I purchased little glass beads to allow for the products to stand up better
   
   My paper towel drawer has a holder which I created using a wooden dowel and clay
   
   Also, I grabbed plastic liquid dispensers to easily get to my various liquids
   
   Managed to slice my finger open making little lids of acrylic to hold all my disposable paper products
   
   *Most of my other acrylic pieces have been purchased from MUJI
   
   
   I hope you enjoyed my ~teal battlestation~, if you have any other questions about it feel free to ask. And I'm sorry if it was unclear at all. And, I'm 100% aware I have a stupid amount of makeup that I've gotten over the years as a makeup artist, Sephora employee, and a true Make Up Addict.

I'd use foam core.