Reddit reviews Upgraded 1S LiPo LiHV Charger Board for Blade Inductrix Tiny Whoop Micro JST 1.25 and JST-PH 2.0 1S LiPo Battery with JST and Micro Losi Cable
We found 3 Reddit comments about Upgraded 1S LiPo LiHV Charger Board for Blade Inductrix Tiny Whoop Micro JST 1.25 and JST-PH 2.0 1S LiPo Battery with JST and Micro Losi Cable. Here are the top ones, ranked by their Reddit score.
Upgraded 1s charger cover and chip for board, provides better 1S LiPo charging experience. Perfect for Blade Inductrix and Tiny Whoop battery charging, also come with JST and Micro Losi adapter cablesCharge 1S LiPo batteries (4.2V) or HV Lipo batteries (4.35V) at the same board by a selectable switch200/600mA selectable current per charge port, charge up to 6 pcs batteries with Picoblade 1.25 or JST PH2.0 power plug at onceInput Voltage: 7-20V, XT60 2S-4S LiPo or DC 12V/3A adapter for field charging and home charging.Do not buy from Peak Eclipse, they never ship items
For being tipsy and full of turkey, you didn't do too bad on those purchases! The 65S Lite and the 800D are both good products for the price. The Beta65S Lite is also a really good flying Whoop out of the box, and can rip when you upgrade the firmware down the line.
The 65S comes with the "stock" version of Silverware. Eventually, you want to upgrade that Beta65S Lite to NFE Silverware. Do that that, you need an STLINK programming tool. Personally, if you've never flown before, I'd wait on doing the upgrade though. NFE Silverware rocks, but it's pretty aggressive. The default Silverware on the 65S Lite is better tuned for a beginner. If you want to program the board, just look at the YouTube video on flashing the 65S Lite to NFE Silverware - it goes through all the steps. The programming pads are tiny, so I ended up just stealing some leftover legs from resistors and shoving those in the pads and then into the connector to the programmer. It wasn't pretty, but it worked.
You definitely want a good radio - the QX7 is probably the better option. They're more expensive on Amazon than through another retailer. I like RaceDayQuads as the prices are good and the shipping is very fast. For the Bayang protocol, you just need a cheap multiprotocol module. The iRange is very good, but expensive. Personally, this cheap one works just fine even though it's fairly short range. BETAFPV has a slightly cheaper and much longer range one, but it can potentially bend the pins on your radio, so I don't really recommend it until that gets fixed. Figure spending about $150 for your radio gear, more if you get a better battery for your radio. (It comes with an attachment for AAs, but it will eat those batteries annoyingly quick.)
The 300mAh battery should work on the 65S Lite - although they are REALLY fast the first 30 seconds or so. I like them, but they might be a bit much for a beginner.
For a charger, there's a bunch of 1S battery chargers out there, most of which are the same design. You also need some power supply to it, but those are super cheap.
For batteries, there are plenty of options. I fly BETAFPV 260mAh for my primary battery, mainly because they come in packs of 8. The 300mAh ones give very long flight times, but they are pretty aggressive. GNB batteries are some of the best, but they are physically longer than other batteries. Crazepony 260 HV batteries are cheap and work well enough. Just remember that you need the PH2.0/PowerWhoop connector instead of the smaller JST 1.25 connector.
For the VTX, you can either keep that as a spare, or mount that to your truck. I doubt it has the right connection to plug right into your whoop batteries, but you can get a PH2.0 pigtail and solder that on to the camera power wires. That will let you connect right to your main flight batteries.
​
Tiny whoop ain't cheap. Racedayquads is my favorite source.
Budget charger I use is on Amazon and you'll need the charging cable as well. Perfectly serviceable for 1s batteries.
Charger is listed in the frequently bought together section.
Upgraded 1S LiPo LiHV Charger Board for Blade Inductrix Tiny Whoop Micro JST 1.25 and JST-PH 2.0 1S LiPo Battery with JST and Micro Losi Cable https://www.amazon.com/dp/B07CJ5ZJ1V/ref=cm_sw_r_cp_apa_i_YCFRDbQDDQTBP
Your mob7 came with either a single connection usb charger or a 6 connection charger board that will need either a DC power supply (5.5mm barrel plug, probably... ) or an xt60 connection (larger battery or a modified DC power supply). Your best bet will be to look for similar 1s lipo charger boards online that come with the DC power supply in order to see what you need to get.
The M8 will only be able to charge 1s lipos with a special wire harness, which you would find searching for "1s parallel charging cable". Parallel charging is not simple and can be dangerous, though. I don't suggest it when you already have a capable charger.
Looking forward, the M8 will also need a DC psu with xt60 for input, and can only charge a single xt60 battery by default, so you would need a parallel board and/or adapters for more xt60 packs or xt30 charging.
Edit: This listing on amazon should look like your charger or you should consider getting something like it for your 1s charging. It has a picture with possible input options (battery, DC psu, DC psu with xt60). The answers section suggests a 5.5mm barrel plug, probably a 12v/3A supply should be purchased. You might have a suitable psu around the house already for smaller laptops or electronics like a router or modem. Other listings might come with a psu for a higher price.