Reddit reviews Anderson Metals 57001-0404 Brass Hose Fitting, Adapter, 1/4" Barb x 1/4" NPT Male Pipe

I posted this the other day but a Reddit user suggested I paint it black to have it absorb more heat so I figured I'd post up the finished product. If anyone is interested here's the materials I used, just cut the rubber hose attached to a new clean insecticide sprayer, attach adapter, put on your hose and boom, camp shower with fairly decent water pressure.

https://www.amazon.com/gp/aw/d/B002SAO7XQ/ref=yo_ii_img?ie=UTF8&psc=1

https://www.amazon.com/gp/aw/d/B001GZZFXA/ref=yo_ii_img?ie=UTF8&psc=1

https://www.amazon.com/gp/aw/d/B0039EEN0M/ref=yo_ii_img?ie=UTF8&psc=1

Homebrew Materials:

Vacuum Pump Oil

Vacuum Tubing

1/4" Barb x 1/4" NPT Male Hose Fitting

1/4" Male x 1/4" Female NPT Extension Hose

Vacuum Pump

Filters

Spatulas

Magnetic Stir Bar

Digital Hotplate with Magnetic Stirrer

Nitrile Gloves (Better than Latex)

Empty Capsules (Buy Separated unless you hate your life)

Capsule Machine (If you value your sanity, buy more than a 100... I hated my life doing this)

Mohr Pipets

Pipette 10ml

Mortar and Pestle (If you're doing orals, get this... Otherwise, you're playing Russian Roulette with your doses and liver)

Funnel (For pouring into small places)

Alconox (For clean your shit)

Temperature Gun (How hot is my shit?)

Graduated Cylinder (If you measure with beakers, you're a fucking idiot... And you should consider Volumetric Flasks)

Beaker Set

1 Liter Beaker (Because brewing en'masse is better)

Scale (I have a 2kg one, too)

Calibration Weight Set

Calibration Weight 100g (Because you need two for the scale linked)

Vacuum Regulator (Unless you want to filter 9001 times due to broken shit)

Oil (Any USP grade, filtered or unfitlered)

BB

BA

Butyl Stoppers

Flip Top Seals

Crimper

Vials (Unsealed)

Autoclave (Cheaper than an oven, why are you using an oven?!)

Weight Boats (Buy a million of these. They're cheap and useful)

Did I miss something? Probably. Yes.

Ok dude I got you bro...I want you to check 2 thinks for me. Check to make sure that the plastic duck work from the mass air flow sensor to the throttle body is all attached properly and secured. Play close attention to where it is hooked up to the throttle body with that 8 mm hex on the gear clamp on the driver side that you have to fish through with an extension to tighten. if that all looks good, I want you to take a look on the passenger side front of the valve cover and you will see a small plastic hose that goes forward into the plastic ductwork. Where that hose attaches to the plastic duct the nipple breaks off and then you get a vacuum leak. I would be very surprised if that was not your problem. If that plastic nipple has broken off, go to the hardware store and get a threaded 1/2 inch Barb that you can put a half inch hose onto, heat it up, and twisted into where the plastic piece broke on and then install the hose. like this, but 1/2"

I've shared this here before and it's worth mentioning here too.

I take lawn/garden pressure sprayer and replace the end with a sink sprayer. You'll also need a fitting to connect them which is likely this but you can't know for sure until you have the garden sprayer in hand. This gives me very simple, one handed control over a relatively low flow water sprayer that's designed for rinsing soap off of things.

It's simple, cheap, it doesn't take any electricity and works really well. I can take a full shower including shampoo and conditioning long hair with less than a gallon of water.

http://www.brandtech.com/articles.asp?artid=13

get a valve.

Honestly... I went with a more expensive oil less vacuum pump. Those things are dirty. You need to be careful about potentially contaminating your brew with the oil spewing out of the pump.

If you're going to go this route I would recommend rigging up some sort of glove box to do the vacuuming in (make sure it's sealed from the exhaust of the pump... aka caulk some joints for the hoses to connect to - aka seal something like this (I didn't check the pipe sizes of any of this shit so figure that out) http://www.amazon.com/dp/B002SAO7XQ/ref=cm_sw_r_tw_dp_lmIrub1RDNX7Y into this: http://www.instructables.com/id/DIY-Glove-Box/

here's a good video to illustrate what I'm talking about with the valve (you need a 3 way splitter to allow air into the vacuum line - the top example)

https://www.youtube.com/watch?v=DZe61UyL0lM

You can also turn it off/on and there's relay circuits for that (but they're more expensive). Honestly you should be ok with a valve I believe. Technically you should need more pressure as it filters as the filter gets more jammed up. So you wont be in a situation where it overloads it when you aren't paying attention (tho you need to watch it).

I'm not joking about the glove box. There's a reason they recommend oil less vacuum pumps for lab work (and they aren't cheap).