Reddit reviews ArctiClean 60ml Kit 1 & 2 Thermal Grease Paste Compound Remover and Purifier
We found 6 Reddit comments about ArctiClean 60ml Kit 1 & 2 Thermal Grease Paste Compound Remover and Purifier. Here are the top ones, ranked by their Reddit score.
Two-step cleaning process for removing thermal grease and prepare surface for new applicationConsists of two 30ml bottles - one for removing old material, one for purifying the surfaceDeveloped by Arctic Silver, one of the world experts in thermal compounds and heat transferEasy-to-apply bottles make the cleaning process easier than competing products
Use the link below, I did. Buy this and use coffee filters to remove the paste. Don't use anything else since cotton, paper towels etc will leave lint.
https://www.amazon.com/ArctiClean-Thermal-Compound-Remover-Purifier/dp/B001JYQ9TM/ref=mp_s_a_1_5?keywords=thermal+paste+remover&qid=1559302378&s=gateway&sprefix=thermal+paste&sr=8-5
Best of luck.
It's really cheap and evaporates quickly without leaving residue. Although I suppose using these would ultimately be the best. This stuff will clean and purify the shame off of drag queen.
Make sure you have an anti static wrist strap and/or static mat. Very important. You need thermal paste for your processor, check out this which helps with the inevitable mess that usually comes with working with it the first few times. I suggest testing your components out through out the build. Make sure your PSU runs, then once you get that in and mobo/with processor installed, make sure lights come on. If you have things that are DOA (ha, /u/dedonarrival) then you will need to RMA those, this does happen sometimes, unfortunately.
These are a few tips I can give to someone starting out. I don't know what your level of knowledge on building is. It is important to make sure you get a decent PSU so don't try to skimp out on that. Cable management inside of the tower is important, be mindful of any cables falling next to fans on the PSU, hdd, graphics card, whatever else you got going on.
Liquid cooling is the shiznit but may be complicated for a noobie. /u/theevillightbulb knows all about that shit.
I second /u/GoGoGadgetReddit
I recently replaced the thermal compound on my build (replaced the stock compound on my liquid cooler, wasn't doing very well) and this stuff was great (cleaner and purifier): https://www.amazon.com/ArctiClean-Thermal-Compound-Remover-Purifier/dp/B001JYQ9TM
I'm sure others can offer suggestions on their favorite, but the thermal compound I used was https://www.amazon.com/gp/product/B0087X73FC
i used this arctic silver & their compound remover. Both worked great and my card is running a bit cooler than it did. It's not needed though, i had to order some because of a seperate issue with my card before it blew up.
https://www.amazon.com/Arctic-Silver-AS5-3-5G-Thermal-Paste/dp/B0087X728K
and
https://www.amazon.com/ArctiClean-Thermal-Compound-Remover-Purifier/dp/B001JYQ9TM/ref=pd_sim_147_3?_encoding=UTF8&pd_rd_i=B001JYQ9TM&pd_rd_r=H9FG05WVWTP8KEJN896D&pd_rd_w=za4Ko&pd_rd_wg=pBCBU&psc=1&refRID=H9FG05WVWTP8KEJN896D
I always keep this stuff in the house.
http://www.amazon.com/ArctiClean-Thermal-Compound-Remover-Purifier/dp/B001JYQ9TM/ref=sr_1_1?ie=UTF8&qid=1458680158&sr=8-1&keywords=Thermal+Paste+cleaner
I use 2 microfiber cloths. One is a bit fatter, typically used for drying cars but has no protruding fibers or static. I use that one for the citrus based cleaner in the kit, which dissolves the TIM
The second I use the same type of microfiber cloth I use on my Reidel Stemware and scotch glasses. Very thin light microfiber cloth, like you use on sunglasses/electronics cleaning. The second solution is the "polish" which is really just alcohol.
IF you do it properly, the first solution just sits for 30 seconds or so, then almsot ALL the TIM will wipe up in one swipe. Then you use the other for just the spot cleanup.
Works like a charm.