Reddit reviews Inkbird ITC-1000 Dual Stage Digital Temperature Controller Fahrenheit ＆ Celsius Thermostat with Sensor for 3D Printer,Freezer,Fridge,Hatching ect. (ITC1000)
We found 6 Reddit comments about Inkbird ITC-1000 Dual Stage Digital Temperature Controller Fahrenheit ＆ Celsius Thermostat with Sensor for 3D Printer,Freezer,Fridge,Hatching ect. (ITC1000). Here are the top ones, ranked by their Reddit score.
It does indeed read in deg F.Can control both heating and cooling outputHas an alarm to indicate sensor failure or high temperatureHighly accurate and reliable temperature controllerBe more user friendly than the STC-1000
I use one of these to control some 120V halogen lamps inside my chamber. It can be used to control your heat and also cool with a ventilation fan if the temp gets too high.
DIY sous vide style might be what you're looking for.
I've used this in my sous vide rig. You could wire this up to whatever electric (analog controlled) heating device you want. Then you only have to make it once and you'll know how long it takes.
Let me know if you want to know more.
Craigslist freezer - we chose upright for vertical space. Chest freezer might work - but you would have to figure out how to hang in it.
Temperature controller - there are lots of options. This one is the Johnson 419. You plug it into the wall then plug the freezer into the female lead. It cycles the freezer on and off at the set temperature. There are cheaper options - but I had this one laying around. I'll link some suggestions below.
The fan is a computer fan with speed switch. I wired it to an old 12v wall wort I had laying around in the parts bin.
Meat hooks are just stainless hooks - again from amazon.
Temp controllers:
Johnson - https://www.amazon.com/Johnson-Controls-Digital-Thermostat-Control/dp/B00368D6JA/ref=pd_sim_328_1?_encoding=UTF8&psc=1&refRID=SG7X9CB5Z0VYY8RM7EVB
If you're comfortable with electricity:
https://www.amazon.com/Lerway-All-Purpose-Temperature-Controller-Thermostat/dp/B00BMLCGF8/ref=sr_1_2?ie=UTF8&qid=1481133568&sr=8-2&keywords=temperature+control
Best deal:
https://www.amazon.com/Inkbird-Temperature-Controller-Thermostat-Fermentation/dp/B015E2UFGM/ref=sr_1_1?ie=UTF8&qid=1481133568&sr=8-1&keywords=temperature+control
Meat hooks:
https://www.amazon.com/Meat-Hooks-Inch-Pack-Pieces/dp/B0195CE08Q/ref=sr_1_3?ie=UTF8&qid=1481133886&sr=8-3&keywords=meat+hooks
Fan:
https://www.amazon.com/Antec-TriCool-DBB-Cooling-3-Speed/dp/B00066ISES/ref=sr_1_5?ie=UTF8&qid=1481133824&sr=8-5&keywords=speed+fan+computer
Or be a big spender and get one of those $15 temp controls to cycle that light off and on.
I made one for maybe $60 and it works quite well.
Didn't really do it to save money. Just seemed like a fun project. It isn't quite done, but it is functional. Eventually it won't look so janky and will live in a project box of some sort.
Janky Sous Vide
I just use an stc 1000 temp controller with my heaters. I have used the cheap chinese heaters, eheim ,and most in between. I use the internal temp setting on the heater as a failsafe should my temp controller fail. Though the relays in the stc are n/o so they should fail off, not on. In any case I feel confident using any crap heater lying around since the temp controller is running the show, not some crappy bending metal thermostat trapped in the same tube as the heating element. The stc 1000 is like 15 bucks on amazon. They also make a similar version that is already wired up, though it costs a little more.
Pre wired https://www.amazon.com/dp/B015E2UFGM/ref=cm_sw_r_other_apa_RpJxxbCN93ZZE
Stc-1000 https://www.amazon.com/dp/B00BMLCGF8/ref=cm_sw_r_other_apa_vrJxxb8CMPCKW
I use 2 250 watt eheim currently in my dual 40b setup. That way if one fails my corals stay nice and warm while I replace it. I fear no overheating! Also I keep my house like 65 during winter. So I need some serious wattage. To keep my uncovered tank at 80f