Reddit Reddit reviews LASCO 11-1033 PTFE Pipe Sealant Tape, 1/2-Inch x 100-Inch, White

We found 4 Reddit comments about LASCO 11-1033 PTFE Pipe Sealant Tape, 1/2-Inch x 100-Inch, White. Here are the top ones, ranked by their Reddit score.

Industrial & Scientific
Tapes, Adhesives & Sealants
Caulk
Tape Caulk
LASCO 11-1033 PTFE Pipe Sealant Tape, 1/2-Inch x 100-Inch, White
Pipe sealant tape1/2-inch x 100-inchWhite colorMeets Federal Military Spec # T-27730AOn plastic spool
Check price on Amazon

4 Reddit comments about LASCO 11-1033 PTFE Pipe Sealant Tape, 1/2-Inch x 100-Inch, White:

u/Sways-way · 6 pointsr/DIY

Having just replaced my own kitchen sink recently, and going through hell...

The top part, grey pipe into the white pipe . It's the wrong piece. You want a new connection like your middle one, that threads.

As for the drain that goes into your wall, you want to pull the white pipe out (it should be nesseled into a large pipe - usually black or grey - that is inside the wall) do not yank it. If it pulls out easily, then you need to apply glue. Is it does not budge, that means that it is already glued; which would be a bigger issue that I can't help with on-line.

All items can be found at hardware stores; but I have found that getting the right fitting for the sink is the hard part (when I installed a dishwasher in a house that never had one before). The key is making sure that you either open all the packs and make sure that everything screws together before you take it home, or be super great at visualization. This also needs to be applied to ALL threads, even if they do not leak.

u/CryptoVaper · 5 pointsr/electronic_cigarette

Boxer squonk box clone

This was only $15 from 3FVape (compared to $140 for an authentic). Surprisingly good fit and finish although the bottle is junk. I had to wrap the threads with teflon tape to make an airtight seal with the bottle cap. Otherwise squeezing just pushed the air out and no juice. But seems to work good now.

The thing is tiny and weighs almost nothing when empty. That's a Goon 24 on top with an aftermarket squonk pin. Had to build down to 0.15 to get a decent vape out it (using a Sony VTC5A battery). Normally not a mech mod fan but thought I'd try this since it's so small (especially compared to my Lost Vape Drone squonker) and maybe get the authentic 2x700 version later.

u/Johnny32757 · 1 pointr/Arcade1Up

A little plumber's tape could help as well.

LASCO 11-1033 PTFE Pipe Sealant Tape, 1/2-Inch x 100-Inch, White https://www.amazon.com/dp/B00ITPHXZI/ref=cm_sw_r_sms_apa_i_.p10Bb6C0JMH2

u/cHorse1981 · 1 pointr/Homebrewing

Yo!

1/4" MFL to Beer Nut Adaptor (SS) https://www.amazon.com/dp/B07GQ9T2N9/ref=cm_sw_r_cp_api_i_4RcDDbCETXK69

Brewery Gaskets Brand 25-Pack EPDM Beer Line Coupling Washer +Bonus Sticker! https://www.amazon.com/dp/B01BFK92IO/ref=cm_sw_r_cp_api_i_fTcDDbJ6EAJ62

LASCO 11-1033 PTFE Pipe Sealant Tape, 1/2-Inch x 100-Inch, White https://www.amazon.com/dp/B00ITPHXZI/ref=cm_sw_r_cp_api_i_QTcDDbSM2EVJM