Reddit Reddit reviews Loctite Epoxy Plastic Bonder 0.85-Fluid Ounce Syringe (1363118 )

We found 8 Reddit comments about Loctite Epoxy Plastic Bonder 0.85-Fluid Ounce Syringe (1363118 ). Here are the top ones, ranked by their Reddit score.

Loctite Epoxy Plastic Bonder 0.85-Fluid Ounce Syringe (1363118 )
BonderBonds nylon, polycarbonate, Mylar, PVC, Acrylic, ABS, stainless steel and many other plasticsResistant to solvents, gasoline, diesel fuel and motor OilExtremely resistant to high humidity, moisture and impact0.85 oz
Check price on Amazon

8 Reddit comments about Loctite Epoxy Plastic Bonder 0.85-Fluid Ounce Syringe (1363118 ):

u/heathmc · 3 pointsr/AutoDetailing

I would say epoxy would be a good choice, something like this: http://www.amazon.com/Loctite-1363118-0-85-Ounce-Plastic-Syringe/dp/B0044FBB8C

Or if there is a plastic clip or anything on the inside that would allow you to screw the two pieces together I would do that.

u/AudiVapes · 2 pointsr/funkopop

Never had to repair a pop, but I've done a lot of work with vinyl and similar materials in the past. Sand off the old glue and use a good two-part plastic epoxy. Like this - http://www.amazon.com/Loctite-1363118-Plastic-Bonder-Syringe/dp/B0044FBB8C/ref=pd_sim_263_6?ie=UTF8&dpID=51-tVGTaiQL&dpSrc=sims&preST=_AC_UL160_SR160%2C160_&refRID=17RAMCA184ANJMP3RKDZ

u/admiralkit · 2 pointsr/homeowners

As others have said, it's the ISP's responsibility to fix. That being said, if you're trying to repair plastic in your home you want to use a plastic epoxy or some similar adhesive designed with bonding plastic together. Kids break a plastic toy? This'll patch it back together. Got one of those plastic Adirondack chairs that's cracking? This'll patch it back together.

u/waddledoodlebonedry · 2 pointsr/cloudmaker

Dassabesso.

Going to order my dope ass new front panel and some other cool stuff from your shapeways link here in a couple days. You have any opinions on which glue to use on an acrylic panel for the magnets? I've been reading good things about this stuff.

https://www.amazon.com/dp/B0044FBB8C

u/MeakerVI · 2 pointsr/Nerf
  1. Seems ok, you don't usually need both the alarm & meter though, especially if you use something like this; 60c @1,000 Mah should be fine. C * Mah needs to be ~60 for safe operation.

  2. Yes, but there might be benefit to using something else.

  3. Not necessary, but it is a nice safety feature.

  4. I feel like I've seen them specifically for the demo, but am not sure.

  5. You'll need bondo for shell smoothing. One container of that should be plenty. The adhesive you need for integrating needs to have MMA in it, IIRC this (usually also easy to find locally) has it in it. Regular epoxy putty is ok for setting the switch and some medium gap filling.

  6. Your artistic skill! Following cut lines on the blaster is easier, but doesn't always work out. If you make too big a cut, you can fill it in later with plastic parts, bondo, and epoxy, it'll just be more work. So aim for less cutting then expand as you can.
u/Desolationism · 1 pointr/3Dprinting

Loctite Plastic Epoxy Bonder

Haven't used it. Google says it works well with TPU.

u/HonkHonkFentonCoins · 1 pointr/VertcoinMining

Use plastic epoxy. This stuff works great.

u/Yowomboo · 1 pointr/Nerf

Any adhesive using methyl methacrylate (MMA) will work.

Devcon Plastic Welder Link

Loctite Plastic Bonder. It MUST SAY "Plastic Bonder" This stuff. Another link The loctite plastic epoxy without the word bonder on it doesn't work on the same materials. It inconveniently comes in the same color packaging.

I'm pretty sure there are others available but I don't know their names. If you look at the packaging and it says methyl methacrylate you should be good to go.

/u/Raviable