Best cargo bed cover accessories according to redditors

We found 6 Reddit comments discussing the best cargo bed cover accessories. We ranked the 5 resulting products by number of redditors who mentioned them. Here are the top 20.

1. Genuine Toyota Accessories PT278-35160 Bed Cleat

2 mentions
Genuine Toyota Accessories PT278-35160 Bed Cleat
Each bed cleat holds a maximum of 110 poundsMade of sturdy black nylon plastic; each tie-down bed cleat measures approximately 6 € x 1 €Fully adjustable, each tie-down bed cleat slides along the Tacoma bed rail system using a spring-loaded, twist/locking clamp to hold it in placeCountry of Ori...
Read Reddit commentsView price

2. TMB Motorsports Black Cargo Cover Compatible for 2014-2018 Subaru Forester

1 mention
TMB Motorsports Black Cargo Cover Compatible for 2014-2018 Subaru Forester
Fits All: 2014-2018 Subaru ForesterFull trunk coverage, clips behind the headrestsHigh-Density Black Canvas with aluminum support barEasy and Tool free installation, no assembly requiredRetractable cover to restore vertical cargo space, pull handle raiser for easy operation
Read Reddit commentsView price

3. GCi STRONGER BY DESIGN G-1 Clamp for Truck Cap / Camper Shell (set of 4). Made with Structural Aluminum to Ensure Quality and Strength.

1 mention
GCi STRONGER BY DESIGN G-1 Clamp for Truck Cap / Camper Shell (set of 4). Made with Structural Aluminum to Ensure Quality and Strength.
Set of 4 quality GCI G-1 clamps for short bed. Also available 1 pack (ASIN: B01LF842TA) and set of 6 (ASIN: B01LF6XD2O).Fits CHEVY: Silverado / Sierra 1500, 2500, 3500. Silverado / Sierra ’07 with Cargo Rail. DODGE: Dakota. Ram 1500, 2500, 3500. FORD: F150. MITSUBISHI: Raider. NISSAN: Titan. TOYOT...
Read Reddit commentsView price

4. ESI Super Cap Seal 20 FT (1 1/2" Width x 1/2" Height x 20' Length) EPDM Rubber for Caps 200 lbs or less

1 mention
ESI Super Cap Seal 20 FT (1 1/2" Width x 1/2" Height x 20' Length) EPDM Rubber for Caps 200 lbs or less
20ft seal for mounting a truck cap or camper shell that weighs 200 lbs or less. Fills all bed rail gaps. For 8 ft beds purchase ASIN: B00C7VU9BAComplete kit includes seal, butyl tape, alcohol pads and detailed instructionsHigh quality, long-lasting automotive grade EPDM rubber. Preferred by professi...
Read Reddit commentsView price

5. API AC101 Mounting Clamps for Truck Caps / Camper Shells (4 Pack)

1 mention
API AC101 Mounting Clamps for Truck Caps / Camper Shells (4 Pack)
Set of 4 general purpose clamps designed to mount truck caps on many pick-up truck modelsConstructed of tempered aluminum with a Mill FinishA = 1" B = 1 1/2" C = 0" - 7/8" (See technical drawing above)Made in the USA
Read Reddit commentsView price
Next page

Top Reddit comments about Cargo Bed Cover Accessories:

u/thunder_babe · 2 pointsr/Tacomaworld

I think this is what you mean/are looking for, could be totally wrong though:

https://www.amazon.ca/Genuine-Toyota-Accessories-PT278-35112-Cleat/dp/B007IX14ZW

u/OneHorseCanyon · 2 pointsr/fordranger

Cap seal

u/yeenasty · 2 pointsr/TruckCampers

Sorry for the long delay!

​

Most truck-peeps would use this clamp to secure structures to the truck bed (the same area where camper shells scure down).

​

I was ballin' on a budget, so I actually just took some small F-clamps I had to fasten the cuppy to the truck bed.

​

Lemme know if this helps, can draw a picture if you need!

u/2Legs1Pants · 2 pointsr/SubaruForester

Thanks for your response! All of the information you gave matches up with what I've found so far. I have two questions:

  1. What do the spring-loaded tabs in the sockets look like? My plan is to 3D print an adapter that will fit on the end of an IKEA TUPPLUR roller shade and also into the sockets in the vehicle. The housing would be rigid from end to end across the shade and would fit down into the sockets, held in place just by friction/fit of the adapters and the sockets. To remove it, I was planning on just being able to lift the retracted cover with attached adapters straight up... but if I could get the geometry to fit with the tabs on either end it would be more secure.

  2. In regards to the short rear seat cover attachment, I've seen that some newer models have a slit in the fabric and attach to the metal posts of the headrests. Is this a desirable feature that should be included in my design? I assume it is to allow the seats to move/recline independently -- which would be an improvement over a rigid bar that wouldn't move with reclined seats and definitely wouldn't move independently with reclined seats. Any insight you can provide on that would be greatly appreciated.

    Thanks again!
u/MaidenATL · 1 pointr/roadtrip

Actual camper shell clamps:

http://www.amazon.com/API-AC101P4-Mounting-Clamps-Camper/dp/B002R7VP6M

C Clamps:

http://m.lowes.com/pd/IRWIN-3-in-C-Clamp/50214643


The Camper clamps are cheaper than I thought. You may find them at an auto parts store.

You'll also need some sort of foam tape to seal the shell to the bed. Not sure about that. Just do some research.


u/spadedracer · 1 pointr/ToyotaTacoma

I used the bed cleats that came with my truck, they fit into the built in rails in the bed.