(Part 3) Top products from r/electricians
We found 47 product mentions on r/electricians. We ranked the 1,753 resulting products by number of redditors who mentioned them. Here are the products ranked 41-60. You can also go back to the previous section.
41. Klein Tools 85191 Screwdriver / Conduit Reamer, Conduit Fitting and Reaming Screwdriver for 1/2-Inch, 3/4-Inch, and 1-Inch Thin-Wall Conduit
Sentiment score: 1
Number of reviews: 3
Hooded-blade design keeps tip from slipping out of screws, especially when tightening hard-to-reach conduit fittings; thicker hood is designed for rugged useReams and smooths 1/2-Inch (13 mm), 3/4-Inch (19 mm), and 1-Inch (25 mm) thin-wall conduit ends to protect wire and permit correct installation...
Show Reddit reviews42. Knipex 8603180 7-Inch Pliers Wrench (86 03 180)
Sentiment score: 2
Number of reviews: 3
With narrow gripping jaws- for fastening/loosening situations requiring a slim toolFast adjustment by pushing a button directly on the work piece and replaces a complete set of spannersParallel jaws allow infinitely variable gripping of all widths to the specified maximum sizeFor careful installatio...
Show Reddit reviews43. Fluke Networks 26000900 Pro3000 Tone Generator and Probe Kit with SmartTone Technology
Sentiment score: 2
Number of reviews: 2
Tone and trace wire on non active networks; SmartTone technology provides 5 distinct tones for exact pair identification; Battery: 9 volt alkalineSends a loud tone up to 16 kilometer (10 miles) in most cables and provides 5 distinct cadences for isolating individual wire pairsPrecise SmartTone techn...
Show Reddit reviews44. Ugly's Electrical References, 2014 Edition
Sentiment score: 0
Number of reviews: 2
Show Reddit reviews45. Reliance Controls TF151W Easy/Tran Transfer Switch for Generators, Small, Gray
Sentiment score: 0
Number of reviews: 2
Designed for control of a single circuit in the event of power failure and uses standard grounded Extension cord18-Inch pre-wired aluminum conduit allows for easy connection at circuit breaker panelMaximum generator running watts: 1, 875Maximum single-pole circuits: 1, maximum double-pole circuits: ...
Show Reddit reviews46. Gardner Bender GSP-04 Electrical Switch and Receptical Spacers, 4 Piece Pack, Neon Green
Sentiment score: 0
Number of reviews: 2
Adjusts depth of receptacles, switches, to allow proper fit of trim plates4-Inch stack of spacers twist apart easily for desired thicknessIncludes 4 strips of 8 spacers each
Show Reddit reviews47. Heath Zenith SL-125-02 Wired Door Chime Transformer
Sentiment score: 1
Number of reviews: 2
Low Voltage Hardwired TransformersWired Door Chime TransformerTri-Volt / Clamp-On or panel mount typeInput: 120VAC - Output: 8VAC-10VA, 16VAC-10VA, 24VAC-20VA
Show Reddit reviews48. Southwire Tools American Made RS-101 Seatek Original Roto-Split, Great for 14/2 to 8/4 BX Cable, Trade Size of 3/8", Thumb Screw, Self-Tightening Blade System, Makes Cuts Quickly and Easily
Sentiment score: 0
Number of reviews: 2
MADE IN AMERICAOriginal roto split field-proven quality cutter accepts BX cable from 14/2 to 8/4 and 3/8"Flex as well as AC, MC & HCF cablesSelf tightening blade system covers the complete cable size range without using a thumb screw and prevents you from damaging the cablesAfter initial setting, on...
Show Reddit reviews49. Wiring a House: 5th Edition (For Pros By Pros)
Sentiment score: 1
Number of reviews: 2
Wiring a House
Show Reddit reviews50. Klein Tools D333-8 Conduit Locknut and Reaming Pliers
Sentiment score: 1
Number of reviews: 2
Tightens 1/2-Inch (13 mm) and 3/4-Inch (19 mm) EMT or 1/2-Inch (13 mm) rigid locknutsFits liquid tight fittings and capsReams and smoothes both inside and outside of conduitKnurled jaws at nose tip pull wire or fish tapeMachined nose fits snugly into locknut wings
Show Reddit reviews51. Bussmann BP/MB-20 20 Amp, 125V Edison Base Plug Fuse Circuit Breaker
Sentiment score: 0
Number of reviews: 2
20A, Edison Base Plug Fuse Circuit BreakerVoltage: 125VDimensions: 5.50"L x 2.75"W x 1.25"H, CardedEdison base manual reset circuit breakerBrass threads with plastic body constructionFits standard Edison base fuse receptaclesResettable upon overload eventReplaces Edison base plug fuses in residentia...
Show Reddit reviews52. Gardner Bender GSW-31 Electrical Pull Chain Switch, SPST, ON-OFF, 6 A/125V AC, 6 inch Wire Terminal
Sentiment score: 2
Number of reviews: 2
Perfect for home applications such as fans and appliancesSpecifications: 3 A / 125 VL, 6 A/125 V AC, 3 A/250 V AC75°C max. temperature ratingTerminal Type: 6 inch. wire leads, 18 AWG Wire
Show Reddit reviews53. GE 6 Outlet Wall Plug Adapter Power Strip, Extra Wide Spaced Outlets for Cell Phone Charger, Power Adapter, 3 Prong, Multi Outlet Wall Charger, Quick & Easy Install, For Home Office, Home Theater, Kitchen, or Bathroom, UL Listed, White, 50759
Sentiment score: -1
Number of reviews: 2
More outlets : 6 outlet wall plug adapter power strip expands 2 grounded outlets into six to power any smartphone including iPhone and Android, lamps, laptops, hair dryer or other electronicSpace saving design: This outlet tap has 3 Standard outlets and 3 extra wide spaced outlets to fit the bulky c...
Show Reddit reviews54. Platinum Tools 15015C Cat5/6 Cable Jacket Stripper
Sentiment score: 0
Number of reviews: 2
Accepts Cable Diameters From 0.18" To 0.25" (4.5mm - 6.3mm).long Life BladeRemoves The Cable Jacket On Cat5/5e/6 CablesWill Not Nick Inner ConductorsDurable High Impact Plastic Housing Is Molded From Yellow Plastic To Make It Easier To Locate
Show Reddit reviews55. Belkin BP11223008 12-Outlet Pivot-Plug Power Strip Surge Protector w/ 8ft Cord – Ideal for Computers, Home Theatre, Appliances, Office Equipment and More (4,320 Joules)
Sentiment score: 2
Number of reviews: 2
12 outlet surge protector power strip with 8 feet /2.4 meter cordSpace saving combination of rotating outlets (8) and stationary outlets (4)Safeguards computers, appliances, home theater and office equipment from potentially damaging power surgesBacked by lifetime warranty and protected by $300,000 ...
Show Reddit reviews
57. Fi-Shock A-53 Wire Stretcher
Sentiment score: 0
Number of reviews: 2
Designed to help with splicing and stretching fencing wireSecurely holds both ends of the wire as you spliceMakes it easier to repair your fence lineRugged design features strong hooksConvenient ratchet action for easy use
Show Reddit reviews58. Electrical Machines, Drives and Power Systems (6th Edition)
Sentiment score: 2
Number of reviews: 2
Show Reddit reviews59. CLC Custom Leathercraft 5023 Deluxe Cordless Poly Drill Holster, Black
Sentiment score: 2
Number of reviews: 2
EASY ACCESS TO DRILL: This drill holster has a safety strap with quick-release buckle for easy access to your tools.DURABLE DRILL HOLSTER: This Custom Leathercraft drill holster is made of polyester material for added durability.STAY ORGANIZED: This drill holster contains multiple outer pockets and ...
Show Reddit reviews60. Westinghouse Lighting 0103600 Saf-T-Pan, 1/2-Inch Deep
Sentiment score: 0
Number of reviews: 2
Saf-T-Pan allows safe, simple installation of fans and fixtures, ideal for new construction or remodelSupports ceiling fans up to 70 pounds and fixtures up to 150 poundsIncludes five knockouts for Conduit or Romex, one Romex connector6-cubic-inch wiring capacity, electrical pan is 1/2 inches deepInc...
Show Reddit reviews
I use this. https://www.amazon.com/Screwdriver-Thin-Wall-Klein-Tools-85191/dp/B000CER0T8/ref=sr_1_4?keywords=pipe+reamer&qid=1556749964&s=gateway&sr=8-4
​
It's great. It's cheap. Mine was a hand me down.
​
And if you really wanted to save money or something, I've never tried the Green Lee version but they make perfectly great tools and it's half the price.
​
https://www.amazon.com/Greenlee-9753-11C-Conduit-Reaming-Screwdriver/dp/B001HWGKD6/ref=sr_1_3?keywords=pipe+reamer&qid=1556750059&s=gateway&sr=8-3
You likely have everything you need already aside from some good linemans and wire strippers. Probably already keep a sharpie on you and things like that. If you don't have a multi screwdriver I recommend getting one like this . A multimeter (doesn't need to be a fluke lol) and a non contact voltage tester are handy. Wearing the nail apron is a good habit and will come in handy, and I have found drill holsters something like this to come in real handy when the drill is an all day necessity. I used to rock something like these guys for crimping and cutting things I didn't want to use other tools for.
If you'll be doing a lot of commercial work the list gets more extensive.
I haven't read the book /u/logosogol posted, but I had this book for school and it's pretty in-depth, with a decent amount of AC/DC fundamentals as well. Sometimes it gets a bit involved but it is mostly pretty practical.
Just brainstorming but couldn't you just get a covered fixture that will mount to the box and drill a small hole and install an individual pull chain switch?
Like one of these. I'm pretty sure the tip where the chain comes out of unscrews and leaves a threaded head to hold it firmly to the fixture. http://www.amazon.com/gp/aw/d/B000BVXWCQ/ref=mp_s_a_1_5?qid=1420044100&sr=8-5&pi=AC_SX110_SY165_QL70#immersive-view_1420044153378
My buddy has the Knipex lineman's pliers and I have to say they aren't anything special. He still uses his Kleins because they are just more comfortable to use.
I also prefer the Klein lineman's pliers but I like the Knipex for their channel locks and I REALLY like their pliers wrenches
I did pick one of those up when he first started. Do you know if their one on conduit bending is any good. I have another one on the subject, but if Ugly's is better I'll definitely pick it up as a stocking stuffer!
Or these Kleins... That work pretty well, and are great for knocking out KOs.
https://www.amazon.com/dp/B000G67F6A/ref=cm_sw_r_cp_awdb_t1_9LWBDbN6BWNME
Your about 30 years to late to find a decent selection of pull chain wall sconces. Know a few people that have had a similar issue.
Solution, buy pretty much any wall sconce you want and a pull chain swtch like this. https://www.amazon.com/Gardner-Bender-GSW-31-Electrical-Terminal/dp/B000BVXWCQ/ref=mp_s_a_1_3?keywords=pull+chain+switch&qid=1557452640&s=gateway&sprefix=pull+chain+sw&sr=8-3
Drill hole though back plate of light and mount/ wire the swtch between the lights hot and the hot wire in the box.
Though if you just want cheap i guess you could just go with this.... https://www.amazon.com/Leviton-8827-CW4-One-Piece-Incandescent-Lampholder/dp/B00002N7JE/ref=mp_s_a_1_130?keywords=utility+pull+chain+light&qid=1557452978&s=gateway&sr=8-130
Something like this would let you trace through that conduit most likely, i've used it to follow wire run in EMT inside of cement blocks before. It was very, very feint in that scenario but it worked.
http://www.amazon.com/gp/product/B000FTADX0?ie=UTF8&camp=1789&creativeASIN=B000FTADX0&linkCode=xm2&tag=vrefid-20
Generally it is pretty loud, especially at a receptacle or panel and can work through drywall as well.
I don't know what kind of work you do, I do everything, and once in awhile these save the day. They aren't tools I use often but they make life easier sometimes
Screw Extractor set
Knipex Plier Wrench
Klein tube cutter
Deep sockets in small case with an Impact Adaptor
Klein cct finder
I have a drill holster on my tool belt and I love it for climbing ladders. It has a buckle on it to make sure the drill can't fall out and it has some spots to put bits. Here's the one I have: CLC Custom Leathercraft 5023 Deluxe Cordless Poly Drill Holster, Black https://www.amazon.com/dp/B000LNM2H0/ref=cm_sw_r_cp_apa_i_dCjyDbNXKQVRN
For my technologist program focusing on power systems (Canada) we used Electrical Machines, Drives, and Power Systems. It covers industrial control, generators, motors, power electronics, transformers, utilities and some PLC. It's qualitative and focuses on application, construction and operation. It does contain math but it stops at complex algebra for analysis with phasors. Not sure what level you're interested in refreshing but it can go pretty in depth with some heavy readings. I'm in eng school now and although it's not quite an engineering textbook, it kinda falls under the requested categories.
the best way to convert 120VAC to 24VAC is with a transformer
search Amazon for doorbell transformers... here's one for less than $15
Thanks for the advice!
I have one of these Belkin surge protectors: http://www.amazon.com/gp/aw/d/B000JE9LD4/ref=aw_d_pd_electronics
and one of these APC Surgearrest surge protectors: http://smile.amazon.com/gp/aw/d/B0012YLTR6/ref=mp_s_a_1_1?qid=1397065424&sr=8-1&pi=SY200_QL40
As a side note, would my electrician be okay with me running the Romex (not connected on either end?
Oh jeez.. Any cheapy little power bar with surge suppression built in.
Like these:
http://www.amazon.com/Belkin-BP112230-08-Pivot-Plug-Surge-Protector/dp/B000JE9LD4/ref=sr_1_1?ie=UTF8&qid=1371707363&sr=8-1&keywords=Surge+power+bar
http://www.amazon.com/Monster-MP-AV-800-PowerCenter/dp/B00003CWDH/ref=sr_1_2?ie=UTF8&qid=1371707363&sr=8-2&keywords=Surge+power+bar
Those look like the alligators, I think he's referring to these which I've heard great things about but I don't quite do enough work where they'd be needed to justify them for myself.
Looking on Amazon it looks like they are selling them again. They may have just been discontinued from home depot, lowes, and supply houses in my area. But it is these Conduit Locknut and Reaming Pliers Klein Tools D333-8 https://www.amazon.com/dp/B000G67F6A/ref=cm_sw_r_cp_apa_DjBQBb0DAC9DB
If you're doing residential, Wiring a House by Rex Cauldwell is a good non technical supplement to your textbooks
https://www.amazon.com/Platinum-Tools-15015-Jacket-Stripper/dp/B000FI2RVC
not sure if this one has a set screw to limit cut depth.
https://www.amazon.com/Coaxial-Cable-Stripper-RG59-RG58/dp/B01NBODKDJ/
coax stripper is another option, but those sometimes only have set cable diameters.
if you're terminating a whole panel, this type of jacket cutter is much easier than regular strippers
https://www.amazon.com/Benfield-Conduit-Bending-Manual-Jack/dp/0872885100
Ugly's book is great too, but Benfield's is cheaper.
Exactly. Something like this:
Fluke Networks Pro3000 Tone Generator and Probe Kit
I’m surprised you don’t have an armored cable cutter yet.
armored cable cutter, Amazon
This book
Don't let the "For Pros by Pros" tagline scare you. This is super accessible to DIYer's as long as they have the basic know-how.
Not a fan rated box, and those look like drywall screws. I wouldn't hang a fan from that in it's current form. I'd take the box down and try to see what the screws were attached to. If it's a solid 2X4 spanning two joists or trusses, mounting a fan rated box like this or this should do it.
https://www.amazon.com/Fi-Shock-A-53-Wire-Stretcher/dp/B000KCN6M2/ref=sr_1_8/179-2591825-2121346?ie=UTF8&qid=1466618029&sr=8-8&keywords=wire+stretcher
imagine the look on your journeymans face when you actually come back with a wire stretcher
Anytime... And this http://www.amazon.com/Uglys-Electrical-References-2014-Edition/dp/1449690777
Fi-Shock A-53 Wire Stretcher https://www.amazon.ca/dp/B000KCN6M2/ref=cm_sw_r_cp_apa_ze7WAbCHYCDP8
Price range?
A Leatherman Surge with 40-Bit Assortment, Extension Driver and Saw and File Blades is something she'll keep forever although not specifically electrical.
Ugly's Electrical Reference is something every electrician should have.
Use this.
Just buy a real transfer switch.....
http://www.amazon.com/Reliance-TF151W-Single-Circuit-Generator-Generators/dp/B000HRWG8U
You should buy one of these
https://www.amazon.com/gp/aw/d/B000BQK0FS/ref=mp_s_a_1_1?ie=UTF8&qid=1501727248&sr=8-1&pi=AC_SX236_SY340_FMwebp_QL65&keywords=ideal+device+spacers&dpPl=1&dpID=31kr5pgxhpL&ref=plSrch
A pipe reamer [bit attachment]. The automatic version of this:
https://www.amazon.com/Klein-Tools-85191-Conduit-Fitting-Screwdriver/dp/B000CER0T8
*clarified
This is what you’re looking for
Gardner Bender GSP-04 Electrical Switch and Receptical Spacers, 4 Piece Pack, Neon Green https://www.amazon.com/dp/B000BQK0FS/ref=cm_sw_r_cp_api_i_9coVDbYXR5ZFV
Someone linked to this the other day, so it was in my history. Find where the existing doorbell is and replace it if it can't output the voltage you need.
https://www.amazon.com/Heath-Zenith-SL-125-02-Wired-Transformer/dp/B000BQY88I
Put one of these on once & forget.
For the MC strippers, those are dikes. Which definitely work but some contractors won't let you use them because it can damage the wire if you don't know how.
They might want something this:
All right! This has been incredibly instructive.
My plan is now:
I have more questions:
Thanks again. My beverage karma to you all is immense.
what you should use:
https://www.amazon.com/Platinum-Tools-15015-Jacket-Stripper/dp/B000FI2RVC
what I actually use:
https://www.amazon.com/Classic-Full-Size-Lighter-Maxi/dp/B0086630A2/ref=mp_s_a_1_8?keywords=bic+lighter&qid=1571335177&sr=8-8
just put your man hands on, heat the wire where you need to strip it, twist and pull the end off. not the cleanest cut, but it works. tired of those spinner style cutters nicking the inner wires.
Are you talking about one of these Klein Tools 85191 Conduit-Fitting and Reaming Screwdriver https://www.amazon.com/dp/B000CER0T8/ref=cm_sw_r_cp_tai_42Otzb2WQZ9KY
I see your point in potential time saving but I don't agree that it's just flat wrong.