Reddit reviews 3-IN-ONE Multi-Purpose Oil, 3 oz.
We found 9 Reddit comments about 3-IN-ONE Multi-Purpose Oil, 3 oz.. Here are the top ones, ranked by their Reddit score.
Multi-purpose lubricant reduces friction and silences squeaky components such as hinges and wheelsOil penetrates into crevices to release parts that have been rusted togetherLubricant cleans tools by removing dirt and grime3-oz. squeeze bottle offers control over the amount of lubrication dispensedDrip applicator with attached cap enables precise application of the desired amount of lubricant
For a kit, as I did my first one last year, the biggest tip i can give you is be patient. Assembly will take a long time. Make it a weekend project. Take breaks. Don't work on it while you are tired. You may be able to finish it in a day, but I'd bet there will be mistakes. Mainly those that will cause skewed axes and an un-level bed. The autolevel can only fix so much.
Calipers are also a great tool to have. You can get a decent set of metal, digital calipers for like 20 bucks. Also helps you determine if your x-y frame is square.
As you build the axes, make sure you orient the bearings exactly as in the instructions. The bed and extruder assembly should slide up and down the rods with zero resistance with the belts off. If it binds at any point, your rods are not parallel. Tweak spacing and re-test. Don't do anything else until that is perfect. If you ignore it, at best you get some artifacts in your prints or some excess noise. At worst, you eventually wear down the bearings and belts prematurely.
Also, get sewing machine oil. Not WD40, not grease. Something like this:https://www.amazon.com/3-IN-ONE-Multi-Purpose-Oil-3-oz/dp/B0083V8LPO
Keep the bearings lubricated with that. You dont need the rods wet with oil. Just a drop on each bearing then move them on the rods. Probably once a month. More if you are printing non-stop. The bearings will already be oiled though. So you're ok for a little while out of the box. I used "Super Lube" silicone grease and I'm pretty sure its what ruined my bearings and rods. All grease does is trap dust and debris and causes friction. Combine that with a year of daily use, I ended up gouging grooves into my rods. Prints were ok but the printer got super loud. I also ended up deforming the plastic inner housing of my bearings because my rods were not perfectly parallel. Issues I just fixed last weekend when I rebuilt mine with new rods and bearings. The whole thing slides super cleanly.
After that just be prepared to learn. This isn't always an load and print thing. There will be a lot of trial and error and many, many failures. Every spool of plastic can be different. I've largely been OK with just the Prusa Slic3r presets but on occasion I'll need to fiddle with temperature, fan speed, infill and perimeter settings. Don't be afraid to experiment or seek out advice if you get stuck.
Hope some of this helps. Enjoy!
Are you maybe looking for something like 3-in-one oil?
If so here it is on Amazon.
It's just the name of the oil, like this, you should be able to get it or something similar most places.
Put it wherever you can get to, let it soak in a bit, add some more, wrench on it a bit...
Take the card out of the case, and have a good look at how to fans are attached to the heatsink, there should be a way to get the fans off. You'll most likely need a control screw driver to remove the tiny screws mounting the GPU fans to the heatsink.
Once the fans are off, there should be a sticker on the back side of the fan motor. This doubles as the back cover and seal of the motor of itself. Peel it off and you will see a bearing(most likely sleeve bearing instead of ball, Cheapo-depot) with a small portion of the fan shaft protruding through it. It will be held in place by a small round plastic retaining clip. Put a small drop of oil on the bearing under the retaining clip(don't go crazy or it will fly everywhere when you turn the fan on) I use stuff like 3-in-one and spin it by hand. Put the sticker back on, if it got oil on it and won't stick properly just and a tiny amount of super glue and hold it until dry.
There are many types of fans on gpus, some will come apart how I described, some will be a low profile two piece fan with a solid back that you have to pull apart. I'm not going to describe it, I'm dumb and should just link a guide
Technically if the fans noisy, the bearing is most likely shot. However I've had numerous fans run for a very long time(still are in fact) without noise just by using this method.
edit: Screwdriver set I don't own personally but will definitely work
I got this one, do you think it will work?
As long as it says rust prevention it should be fine. I personally use this
https://www.amazon.com/3-ONE-100355-Multi-Purpose-Pack/dp/B0083V8LPO/ref=sr_1_1?ie=UTF8&qid=1483754990&sr=8-1&keywords=3+in+1+oil
My doors were a bitch to get off and on, but after using some oil inside the hinges it's awesome now. I just keep a bottle of this stuff in my console. You can get it almost everywhere.
http://www.amazon.com/3-IN-ONE-Multi-Purpose-Oil-3-oz/dp/B0083V8LPO
https://www.amazon.com/3-IN-ONE-Multi-Purpose-Oil-3-oz/dp/B0083V8LPO
Usually graphite lube comes in a little tube like this. http://www.mrlock.com/image/cache/data/ic/items/23065-500x500.jpg. Orielleys or Napa should carry it. Another one that I've used is http://www.amazon.com/3-IN-ONE-Multi-Purpose-Oil-3-oz/dp/B0083V8LPO. It might be easier to find. But with either one just remember that a little goes a long way.