Reddit reviews NavePoint 1U Rack Mount 4-Post Shelf Rail Full Depth - 33.5 Inches deep
We found 9 Reddit comments about NavePoint 1U Rack Mount 4-Post Shelf Rail Full Depth - 33.5 Inches deep. Here are the top ones, ranked by their Reddit score.
These rack mount adjustable rails kits allow you to support devices on your 19", 23" or 30" rack without having to mount them directly.Full, nested floor allows weight to be distributed in front and back.Depth can be adjusted up to 33.25" deep.Support up to 110 lbs when properly installed to a 4 post rack or cabinet.Both 10-32 and 12-24 mounting screw kits are included allowing mount on either thread pattern.
They're not being shitty but being truthful. A lot of telcom and professional audio / video recording studio gear used threaded hole racks but the computer industry pretty much standardized on square mounting holes that ball bearing sliding rails snap into as well as using cage nuts that fit square holes.
You can use a round hole rack for computer equipment but he'll need to buy several sets of L bracket shelves to hold his gear. You can buy round hole to square hole adapter brackets so a square hole sliding rail set can mount to the frame but now that free rack suddenly becomes more expensive each time a piece of gear is added to it.
He'll also have to go to Ace Hardware, buy a few different sized machine screws and try them out until he finds the right diameter and thread pitch that will fit his rack. It could be 10-32 or 12-24.
I'm in the market for a rack and every time I see one for sale that has round holes, I close the tab for the reasons I outlined above.
It looks as if the round hole sections can be removed, if he can find a square hole conversion kit that will fit, then it was a good deal to get it.
I didn't get enough either. You can see I stuck a few in the divider between the mobo and drives so I knew which ones went there. I'll check today and let you know, I have a really good (labeled) bolt collection so I should be able to figure it out.
Rackmounting- I just mounted these rails and slide it in on that.
You should be able to transfer parts, but if you've got the room in your rack for the T610 chassis and no reason to free it up, either buy the conversion kit, or go cheap and get a Navepoint rail shelf or something similar. I've used one of those to hold a massive 5U steel pedestal chassis with 14 drives in it and had no issues.
4x of these will set you back only $120.
https://www.amazon.com/gp/product/B00XXDHPEU/ref=oh_aui_detailpage_o05_s01?ie=UTF8&psc=1
Been using this for the past few weeks for a Dell R715. Works great.
In case anyone finds this by Googling later, I experimented with two different generic rail kits, for science:
** I tried these first, and they DO NOT fit a Lenovo SA120 in a standard 19" square-hole rack. The design of these rails means they stick inwards about 1/4 centimeter beyond flush with the rail, making it an extremely tight squeeze for larger hardware like a (2U) SA120. While that alone might still be usable in some racks, additionally the depth of these rails is adjusted with some screws that have heads that stick yet another few millimeters inside, making it impossible to seat the machine. It might be possible to make the squeeze if you have a round hole or threaded rack, but I wouldn't chance it.
** These worked for me. They're a similar design to the NavePoint, but they leave a few precious extra millimeters between posts that made all the difference. It's still a tight squeeze, and I had to remove the SA120's rack ear protectors to make it fit (you can put them back on after), but it's in there good and securely, and flush with the rest of the equipment. Looks great.
Thanks to /u/Mthrboard for pointing me in the right direction, and to /u/donnydavis for offering to sell me a genuine kit!
Ideally, you get rails specifically for your server. You attach the rails to the rack (front and back), and then slide the server onto the rails. However, generic shelf rails like this are generally cheaper if your server didn't come with the fancy rails.
And no, that last rack you linked is not going to support an actual server. That is only for shallow/lightweight devices like simple switches, patch panels, and some smaller appliances.
Dell Tower Server, T620 [ 100 lbs ] that I wish to mount inside a 4post, square hole server rack.
Will these work ?
https://www.amazon.com/NavePoint-Mount-4-Post-Shelf-Depth/dp/B00XXDHPEU/ref=sr_1_13?ie=UTF8&qid=1537471248&sr=8-13&keywords=2u+adjustable+shelf
as they can extend to cover the 30" depth of the Dell T620 or is something heavier duty required
I'm installing a rackmount UPS soon too and I plan on using the shelf below. It supports up to 200 lbs which should be more than enough for your model.
NavePoint 1U Rack Mount 4-Post Shelf Rail Full Depth - 33.5" deep https://www.amazon.com/dp/B00XXDHPEU/ref=cm_sw_r_cp_apa_JoIKAbPKRTFYZ