Reddit reviews Official Creality 3D Extruder Feeder Drive MK-8 Aluminum Upgraded 1.75mm for CR-10 Ender 3 CR-10S

I've owned the Ender 3 for a few months now and have made a number of upgrades, both purchased and printed. Here's a list of what I have purchased and printed, sorted by importance/usefulness.

 

Purchased Parts:

1. EZABL - An automatic bed leveling solution that has worked really well for me. TH3D's firmware and documentation are top notch. Once I dialed it in I've had no issues with bed leveling or adhesion. Also note, TH3D is an American company and Tim, the owner, is even a mod of this sub!
   
   
2. Stepper Motor Dampers - A great way to quiet down the printer. My bedroom and office are connected without an intervening door and the dampers allow me to print overnight and still get get to sleep. Some users have had issues with stepper motors running hot with the dampers installed, but I've had no trouble at all, even after 16+ hr prints.
   
   
3. 5015 Blower Fan - For use with the Petsfang Duct, see below.
   
   
   
4. Assorted M3 Screws - If you're going to be making mods to your printer, you're eventually going to need different sized screws. Having various lengths on hand is super helpful when trying to mount a new part.
   
    
   
   Printed Parts:
   
   
5. Filament Guide Arm - This has helped a lot with keeping the filament feeding smooth and preventing under-extrusion issues. There is a more popular model on thingiverse, but I found this version to be stronger and more stable.
   
   
6. Petsfang Cooling Fan Duct - An extremely popular replacement for the part cooling duct and fan. This creates much more even cooling around the filament as its extruded, providing better bridging and better overall print quality. There is a version using a replacement 5015 blower fan, as I have used, and there's a version called the "Bullseye" that uses the stock fan. I chose to replace the stock fan because mine was starting to rattle.
   
   
7. Tool Holder - It sounds frivolous, but having the tools you need right at hand can be a big help in saving a print or performing trouble shooting. Definitely a must have.
   
   
8. LCD Rear Cover - Protects the circuit board behind the LCD, which is exposed from the factory. If you have children like I do, this is a must.
   
   
9. Cable Chain - Routs the various cables to their destinations in a clean way. Looks super cool. Not necessary, but definitely fun. Note, there is an X-axis cable chain setup available, but I found it made excessive noise and wasn't worth the trouble.
   
   
10. Fan Shroud - Protects the main board fan from bits of filament falling down into the casing.
    
    
11. Storage Drawer - A handy little drawer that slides in next to the LCD. I store things like alcohol swabs, razor blades, and other random tools in it.
    
     
    
    Future Upgrades:
    
    Spool Roller - One issue I've found is that the stock spool holder requires excessive force from the extruder to unwind filament. A replacement spool roller with bearings should reduce the friction significantly and produce more even extrusion.
    
    Metal Extruder - A common problem with the Ender 3 is that it fails to maintain proper tension on the extruder gear, which leads to failure to feed and poor extrusion. An all-metal extruder has been known to fix the issue.
    
    
    
    
    
    

Replace the part. Then print a filament guide off thingiverse for your model printer.
Official Creality 3D All Metal... https://www.amazon.com/dp/B07J44QW8B
I've seen some people that have printed a replacement, but the metal one will last longer.

You have some underextrusion. The lines you're seeing are caused by too much tension on the extruder gear. It cannot get enough material to the hotend.

Mine was the idler arm breaking under the pressure. Buy the metal one from Amazon or wherever. Then print the filament roller guide. And lastly, print a better holder/roller for your spool.

Hey! Welcome. I also just bought my ender 3 pro as my first printer.

​

Here's a great place to start https://all3dp.com/1/20-must-creality-ender-3-upgrades-mods/

​

​

So far I've done the following upgrades:

1: Metal Extruder. 100% necessary and MUCH easier to do during initial assembly rather than an upgrade. I got mine form Amazon.

https://www.amazon.com/gp/product/B07J44QW8B/ref=ppx_yo_dt_b_asin_title_o02_s00?ie=UTF8&psc=1

​

2. 2020 Filament Guide:

You can find this on Thingiverse and is about a hour long print. It actually made a noticeable different in some salmon skin issues I had in my first couple of prints.

​

3. Springs:

These just arrived today so I'm not sure how much they will help but one of the main causes of my failed prints so far as been issues with leveling and some of the stock springs I can see are just no good.

​

4. TL Smoother:

Another upgrade I havent had a chance to set up yet. That said, my research has come across mixed results. Some people love them and some people Hate them.

​

I'm not sure about glass beds and all, the stock plate has been working pretty well for me. I think I'm going to try it alittle more before moving to a glass bed simply cause its a bit easier to maintain but it could be the next thing on my list. I've also been considering an auto-leveler (and ardunio) since it doesn't have that function and having to relevel, watch, pray, reset has already cost me a couple hours of print time.

​

I'm not familiar with ESUN PLA+, I've been using https://www.amazon.com/gp/product/B00J0GMMP6/ref=ppx_yo_dt_b_asin_title_o07_s00?ie=UTF8&psc=1

and am very happy with it so far.

​

Best of luck with your printing!!

Hey I also new on this, got my printer a month ago, I was super exited as everyone here when receive their printer, I read a LOT while waiting for the printer, so I heard that the stock bed springs are crappy, so I ordered this ones FYSETC Bed springs, also ordered the Aluminium Extruder feeder, and read about the leveling, the paper sheath method, which I think you should already heard about, I did it at the first time the printer gave me a nearly perfect first print (demo dog) , after a few prints and on my third print I came home just to find a mess on my printer, so I did my research again, find out it was bed adhesion, and find out that the best way was glass bed + PEI sheet was the best option, while waiting to arrive I tried to clean the stock bed sheet with mineral spirits (did have rubbing alcohol) but it worsened the adhesion, so I used one adhesion sticker that comes with the overture filament, and again flawless adhesion, at least for the first 4 prints, then again the frustration, I tried some glue stick and worked but it leaves a mess on your print so I decided to try painters tape directly onto the aluminum bed (which lucky for me it is perfectly flat) this is the best adhesion I have tried, problem is also makes a mess with the down face of the print, Finally mi Gass-PEI arrived, (3 days ago), it has a great adhesion but is not perfect, also you have to raise the Z limit switch to compensate the 5~ mm of Glass-PEI, find out that it isn't perfectly flat it has a good adhesion and leaves a very smooth down face, but at some section it does't sticks well and leaves artifacts on the down face, I'm currently working to fix this.

Sorry for the long post, need to talk about my frustration and let you know you are not alone on this, once you manage to make a good print is very satisfying, I have a PETG filament waiting to be used but I don't think is a great idea to try it until a learn more about 3D printing and the Ender.

I bought this extruder feed from Amazon to replace my plastic one.

I checked a YouTube video real quick and then went for it. It seemed like a pretty straightforward install.

That said, now I look at it, the arm seems canted a bit, almost as if the screw with the bearing on it isn't in all the way? It's in as far as it will go.

I had one short countersunk screw (M2 I think) and a lock washer leftover. Couldn't think of where a lock washer would be useful for this assembly, and the stock one didn't have a lock washer anywhere, but if someone knows where it goes, or anything else to ensure this is on correctly, please let me know.

That said, it seems to be extruding just fine, I've done a couple of test prints and nothing seems amiss.

Thanks for the detailed reply.

​

I need to read more to understand the z switch and z screws you are referring to. I have no idea what those are. I assembled by watching some channel on youtube do it. It was like a tales from the crypt vibe channel.

​

As much as it sucks, I probably need to completely disassemble it and start over. There has to be something done incorrectly for it to be this difficult. I am definitely going to get one of those gauges before I get back into. I returned the springs today and ordered different springs on amazon. When they get here, I might sit down one night and try again.

​

As for the bed, the glass one I got was scratched to hell from those stupid springs. I didn't know I had to raise or lower whatever switch you were talking about. Like I said earlier, I already ordered a SD card reader so that will be a definite mod. As for the octopi, is there a list somewhere on this subreddit of everything you need to purchase before starting? I have a raspberry pi at the house. I originally bought it to build a retropie but I haven't gotten around to it yet. I could use it for the printer if needed. I really like the idea of remote printing, having a webcam to see the print live, and putting a part on there that stops the print if there is a filament issue.

​

I have to go into the city tomorrow so I was thinking of stopping by ikea and getting some Lack Tables for the eventual enclosure but now I don't know if I am even going to keep the Ender 3. I am debating on returning it and moving up a tier. I really want to get started on this but it seems like I am never going to be able to print any of this awesome stuff. So many awesome files on thingiverse and I can't use any of them.....

​

Here are the parts I have purchased so far....

​

SD Card Extension

​

Glass Bed

​

Springs that I bought that would not lower bed enough

​

Most Recent Springs I am going to try

​

Metal Extruder Upgrade

​

Filament Black and Red

The genuine one is $14.99 on Amazon. Look for seller Creality3d Online.

Official Creality 3D All Metal MK-8 Extruder Feeder Drive Aluminum 1.75mm for CR-10 Ender 3 CR-10S https://www.amazon.com/dp/B07J44QW8B/ref=cm_sw_r_cp_apa_i_ViaSCbP7EG11R

Tomb of 3d printed horrors has a great assembly video. https://www.youtube.com/watch?v=me8Qrwh907Q&t=766s

Useful tips also consider getting the aluminum extruder before set-up (its easier to do during the assembly process). https://www.amazon.com/Official-Creality-3D-Extruder-Aluminum/dp/B07J44QW8B

Level your bed! Most of my failed prints have been when my bed becomes unleveled.

I included some helpful youtube channels that helped me problem solve.

Chep - https://www.youtube.com/user/beginnerelectronics

Teaching Tech - https://www.youtube.com/channel/UCbgBDBrwsikmtoLqtpc59Bw

It's going to happen to you. Possibly even with a filament guide eventually. The plastic extruder is just terrible. Picking up the all metal extruder is one of the best buys you'll make.

I'm pretty sure I just got an official creality one, but here is an Amazon link. I'm glad you got it figured out!