Reddit reviews Tamiya America, Inc Angled Tweezers, TAM74003
We found 9 Reddit comments about Tamiya America, Inc Angled Tweezers, TAM74003. Here are the top ones, ranked by their Reddit score.
These angled tweezers are useful for handling small parts and adding decals to your models.Tamiya Quality and PrecisionThe edges are rounded to to prevent scratching.Made from stainless steel with black cationic finish for long life.
If you get it nice and hot you should be able to dig it out with some angled tweezers.
The side skirts are easy enough to pop back on for this guy. I feel like the Zeta being a grenade circlejerk is pretty overblown. Sure, it's more fragile than other gunpla, but it isn't going to permanently break by touching it.
As for the decals, I suggest these tweezers. They work incredibly well, especially for the tiny RG decals.
Personally, for a standard round wire, Temco sells 316L Stainless Steel for mega-cheap. Like $6.64 for 100'. It is the exact same wire that any "vape" company will sell at a huge markup. Stainless works in wattage or Temperature Control, and is my personal favorite.
As for coil wrapping, I prefer these UD Coil Jig sets. I have 2 so for dual coils, I have 2 of each size diameter. I prefer these because the diameter tools remove to help you position your coils after being installed. These require hand-wrapping, but make installation a bit easier. This is personal opinion, of course.
For the Limitless, when I use round wire, I prefer 22g 316L. It is VERY easy to wrap as the wire is large enough to get the wraps near-perfect right off the start; but not so thick that it hurts to wrap it. I usually do 8 wraps around a 3.0mm diameter. This gives you so much surface area that the flavor is really just top-notch. The 3.0mm diameter gets the perfect amount of cotton to keep the wicks the perfect thickness. I run the wicks down to the tip of the glass, and fluff the ends profusely.
If you do end up ordering wire from Temco, 24g 316L SS is also good to keep on-hand. With their prices, you can get 200' of wire for a mere $13. A spool of 15' 316L from UD or somewhere else will easily run you $7-$10 or so. Again, can't recommend Temco wire enough! Haha.
As far as tools, I would HIGHLY recommend a 521 Tab. Geekvape or Coil Master both make a similar tab which runs on a single 18650 battery. Allows you to build, test your resistance, and then pulse your coil(s) for cleanup all from the same surface. Worst case scenario, you always have a backup device by placing an atty of the tab! Not recommended though! Haha.
Angled Tweezers are also HIGHLY recommended for wicking RDTA's. Tweezers, I like pointed tips to fluff cotton. Wire cutters are a dime a dozen, just don't go too cheap as the 22g is somewhat thick, and if you get into more exotic coils, you want to make sure it cuts perfectly 1st try, every time.
These do a great job. Obviously you wouldn't want to carry them with you, but you also probably wouldn't wear them in public.
https://www.amazon.com/Tamiya-74003-Angled-Tweezers-Mk803/dp/B000BN9IF4
Hey everyone!
I'm as new as it gets. So, I made a shopping list after doing some research on everything that I think I need to start. I'll place the links to all the items in the lines below. Everything is on Amazon because... well why not?
Gundam
Glue
Marker
Tweezers
Knife
Cutters
Mat
More Markers!
*Krylon Matte Finish
Am I missing anything?
These are pretty nifty for it :)
The “Eyelure” brand fake lashes come with a super tiny eyelash glue with a tiny wand in it and I always sneak that little bottle in with me for raves just in case they do lift up. So far thats never happened yet but the main lash glue I use is a black glue from the brand “Kiss” and it’s called Lash Couture lash adhesive and I swear it is the stickiest lash glue I’ve ever had and has never lifted.
Also, when I apply my lashes I wait for the glue to become tacky and then I put them on like normal and pinch the lashes at the strip to my lids with tweezers similar to these to secure them: https://www.amazon.com/Tamiya-300074003-Angled-Tweezers/dp/B000BN9IF4
Lash extensions would def be easier and less maintenance though! Good luck with your lashes!!
Hello, I'm just starting with Gunpla and I need some tweezers to apply the stickers to my kits, would this tweezers be good for RG models?
https://www.amazon.com/Tamiya-300074003-Angled-Tweezers/dp/B000BN9IF4/ref=mp_s_a_1_4
I just used a pair of angled tweezers, these to be specific.