Reddit reviews TP-Link 16 Port Gigabit Ethernet Switch Plug and Play Sturdy Metal w/ Shielded Ports Rackmount Fanless Lifetime Protection Unmanaged (TL-SG1016)
We found 13 Reddit comments about TP-Link 16 Port Gigabit Ethernet Switch Plug and Play Sturdy Metal w/ Shielded Ports Rackmount Fanless Lifetime Protection Unmanaged (TL-SG1016). Here are the top ones, ranked by their Reddit score.
16-Gigabit ports provide instant large file transfers32Gbps Switching CapacitySupports IEEE 802.3x flow control for Full Duplex mode and backpressure for Half Duplex modeNon-blocking switching architecture forwards and filters packets at full wire-speed for maximum throughputAuto MDI/MDIX eliminates the need for crossover cablesPlug and Play design simplifies installationLIMITED LIFETIME WARRANTY and 24/7 Tech Support16 10/100/1000Mbps RJ45 ports; Standard 19-inch rack-mountable steel caseInnovative energy-efficient technology saves power up to 40%Supports MAC address self-learning and auto MDI/MDIXAll ports support Full/half duplex transfer mode for 10Mbps/100Mbps and Full duplex transfer mode for 1000MbpsStandards and Protocols: IEEE802.3, 802.3u, 802.3ab, 802.3x, CSMA/CD, TCP/IP Ports: 16x 10/100/1000Mbps Auto-Negotiation RJ45 ports (Auto MDI/MDIX)Basic Function: Wire-speed Performance MAC Address Auto-Learning and Auto-aging IEEE802.3x flow control for Full-Duplex Mode and backpressure for Half-Duplex ModeBackbound Bandwidth: 32Gbps MAC Address Table: 8kForwarding Rate: 10BASE-T: 14880pps/port 100BASE-TX: 148800pps/port 1000BASE-T: 1488000pps/portTransmission Method: Store-and-Forward Network Media: 10Base-T: UTP category 3, 4, 5 cable (maximum 100m) EIA/TIA-568 100? STP (maximum 100m)100Base-Tx: UTP category 5, 5e cable (maximum 100m) EIA/TIA-568 100? STP (maximum 100m) 1000Base-T: UTP category 5, 5e cable (maximum 100m)LED Indicator: Power, Link/Act Safety & Emission: FCC, CE Power: 100~240VAC, 50/60Hz
I wired every bedroom of my house with Cat-6 when I moved in. The office has multiple runs since I have multiple machines on opposite sides of the room. My basic rule is if it's a desktop pc, game console, or cable box, it should be wired. Anything else, let it be wireless.
I didn't want to run a TON of cable, so in most places I just have 1 active ethernet run to an 8 port gigabit switch (a second ethernet is there but not hooked up) and then run to the other devices. So my Xbox One, HTPC, Tivo, and TV are all hard wired to an 8 port switch and then the 8P is ran back to my 48 port core(overkill) switch.
The benefit is that everything is much more stable and less latency which is important when gaming. I can also add an additional access point anywhere that has weak WiFi coverage.
As for cost, I kept my stuff pretty cheap. I didn't do punch downs so as a result, mine doesn't look as clean.
1000ft Cat6 - $100 (http://www.monoprice.com/product?p_id=12792)
Ethernet Ends(rj45) - $~30 (bought locally don't use the monoprice ones, they're not great)
16P Gigabit Switch for "Core" duties - $70 (http://www.amazon.com/TP-LINK-TL-SG1016-1000Mbps-17-3-inch-Rackmountable/dp/B002HAJQGA) - If you wanna go crazy and get a managed switch, check eBay for used HP Procurve stuff that's gigabit, looking closer to $200 probably though.
Ethernet Tools - $<50 - Need a crimper is all. You can buy a cheapo for $30 at most home improvement stores. If you do punch downs, you'll need a punch tool which will be $40 ish.
Miscallenous stuff such as low voltage outlets and wallplates will probably set you back around $5-10 per run.
So I guess a good ballpark figure would be around $300-$400 + your time if you did it on the cheap side. I have a feeling the neat and tidy way he did his setup probably was closer to 700-800.
TLDR: Expect to spend at least $300 to wire up a house with ethernet. You'll probably end up spending a lot more if you want it as clean as OP's.
What you want to do is take the cables that are placed into that hub thing and plug them into a switch instead.
The hub is for phone lines and will not work the way you are tying to.
&nbsp;
Before plugging the cables into the switch, check out their cable layout inside the RJ-45 jack (the cable end).
Make sure all 8 cables are there, and connected in the right order: either the common 568B or the 568A way.
It is important, especially if the rooms are not yet punched down or crimped (with a RJ-45 end), as you will need to match cable layout on both ends of the cable.
&nbsp;
Now that cables are all set up right, labeled, and properly cable managed, you can plug them into your router or switch (depends on how many you have).
If you have more cables than your generally 4 port router can support, then just get a 16 or 24 or 48 port switch.
As you can see, price goes up just a little between 16 and 24 ports, but massively to 48 ports.
Get the one you need, plug everything in, then plug one cable from the router LAN port to a switch port, and you are in business.
Patch Panels/Cable Management? www.allentelproducts.com
Rack Mounted Powerstrip Audio/Video? Furman PLC-8.
Surge suppressor? Panamax MD2 2 Outlet Direct Plug
Cheap Switch? TP Link 16 porter, https://www.amazon.com/dp/B002HAJQGA/
I'll preface this by saying i'm still very basic to networking so someone correct me if i'm wrong please.
It sounds like you're in need of a switch (unmanaged if you want to plug it in and not configure anything). Here are a couple I found with a quick google search (I have no opinion on either of these, they were just the first thing that came up with a google search.
Rackmount: https://www.amazon.com/TP-Link-Ethernet-Unmanaged-Rackmount-TL-SG1016/dp/B002HAJQGA
Desktop: https://www.amazon.com/TRENDnet-16-Port-Unmanaged-GREENnet-TEG-S16DG/dp/B0044GJ516
I believe the setup for this would be the run from the router coming into the closet, plugged into maybe port 16 of the switch, then ports 1 through 12 are plugged into the front of the patch panel, and the cable runs to each room are punched into the back of the patch panel.
Again, i'm still basically brand new at this, so please someone tell me if this is wrong.
You could get this 16 port tp-link gigabit switch.
TP-Link 16-Port Gigabit Ethernet Unmanaged Switch | Plug and Play | Metal | Rackmount | Fanless | Limited Lifetime (TL-SG1016) https://www.amazon.com/dp/B002HAJQGA/ref=cm_sw_r_cp_apa_hVtYBb8R3TKVQ
This is pretty much what my setup looks like, although with tons more devices and small switches scattered around the house xD. My primary switch is one of these, but they have a cheaper 8-port as well. Most of my gear is in a closet so I have a fan looming over it on low, keeping things cool. Also, putting it all on a UPS means that you can finish sendind that email (or wrapping up that online game) if the power goes out, very handy.
I do not have an Ubiquiti AP yet. From what I know they use PoE, but somehow I doubt they ship with no way to power them out of the box. I have heard they do not play very well with Apple products, in which case I would suggest an AirPort Express (or Time Capsule for that wonderful 24/7 backup) as an additional AP.
The EdgeRouter setup tutorials on the Wiki are designed for WAN on port 0, LAN on port 1, and WLAN on port 2, which would mean the AP would plug right into the router. I personally did not do this, I mixed the LAN and WAN and connected exactly as your picture shows. Let me know if you need any help setting it up.
Thank you again . I was actually going to daisy chain phones and pcs and now that you mentioned I will connect them to separate ports.
This is the Linksys I'm going to use: http://www.linksys.com/us/p/P-LGS116/
and this is the TP-Link I was talking about: https://www.amazon.com/TP-Link-Ethernet-Unmanaged-Rackmount-TL-SG1016/dp/B002HAJQGA
Your setup sounds exactly like what I'm about to move into. I can't afford to do this quite yet (because of just moving into a new house) but my plan is:
Run wires to every fixed location (TVs, desktop, server, all wifi access points, anywhere you think you might put a computer). Set up the APs on different channels but with the same SSID and security. That will allow devices to roam between them.
This is a pretty decent deal. I've had good luck with the TP Link products I've used. I currently have a couple of their smaller switches in service and they're working just fine.
That said, I agree with the other comments about Monoprice.com.
If you got 8 buddies coming... 16 port maybe?
https://www.amazon.com/TP-Link-Ethernet-Unmanaged-Rackmount-TL-SG1016/dp/B002HAJQGA/ref=sr_1_5?ie=UTF8&amp;qid=1511103911&amp;sr=8-5&amp;keywords=16+port+switch
1 port is for the router, so on an 8 port you only have 7 available. Then depending on how you set things up, I like to have a dedicated server PC. Games that support a hosted server goes on that, pre-configured in router for forwarding, and that is the PC that is also open up to file sharing so friends can grab the game, patches, mods, etc.
Generally, 8-port switch is desktop switch. I am curious about what a 8 or 12 port rack mountable gigabit switch is used for. Maybe this TP-Link 16-Port Gigabit Ethernet Unmanaged Switch fit your needs. (https://www.amazon.com/dp/B002HAJQGA/ref=psdc_281414_t3_B004EIFCHK)
You couldn't be more wrong.
Anything that says FULL DUPLEX is capable of delivering speeds symmetrically for an unlimited amount of time. A full duplex gigabit switch will NEVER throttle and slow down anything. A gigabit switch without "full duplex" tag WILL occasionally cause slowing downs, POSSIBLY at least.
There is this great switch, TP-LINK SG1016, which is a full duplex gigabit switch, going on a deal on amazon now: http://www.amazon.com/TP-LINK-16-Port-Gigabit-Ethernet-TL-SG1016/dp/B002HAJQGA for $60.
Definitely worth $60 for a full duplex gig switch over some crap 5 port consumer grade shieeett