Best automotive air filters & accessories according to redditors
We found 39 Reddit comments discussing the best automotive air filters & accessories. We ranked the 28 resulting products by number of redditors who mentioned them. Here are the top 20.
ARB SS172HP Safari Snorkel Intake Kit https://www.amazon.com/dp/B01N20HBS9/ref=cm_sw_r_cp_apa_JZ5-BbJZ8G8CJ
You can just call it an intake snorkel. If you are driving though high water, one of the week points would be your engines air intake. Mainly, because if that slurps water your engine is good as done. The snorkel takes that point and raises it much higher so your car can take on much higher waters than it would otherwise.
Links to al the stuff I purchased listed below:
Headlights:
http://www.wpdrl.com/Showprot.aspx?id=658
Tail lights:
RCP - RFT01 - Aftermarket Upgrade LED Taillight for 2012-2015 Ford Fusion, Clear Red Rear lamps Lens with Loop Ring Driving light https://www.amazon.com/dp/B01FU39X9K/ref=cm_sw_r_cp_api_i_CFjoDbY02WJRE
Spoiler:
Painted Factory Style Spoiler fits the Ford Fusion 525 G1 https://www.amazon.com/dp/B0104J33ZK/ref=cm_sw_r_cp_api_i_HGjoDb26XJDHF
Antenna:
CravenSpeed Stubby Antenna Replacement for the Ford Fusion 2005-2019 | 4 Inches https://www.amazon.com/dp/B0073X74X8/ref=cm_sw_r_cp_api_i_0GjoDbK3DM47X
Grill:
https://rover.ebay.com/rover/0/0/0?mpre=https%3A%2F%2Fwww.ebay.com%2Fulk%2Fitm%2F162601654749
Sway bar stiffener:
https://www.steeda.com/steeda-ford-fusion-rear-swaybar-13-14
K&N intake:
K&N 69-3533TTK Air Intake System https://www.amazon.com/dp/B00FU9B9HE/ref=cm_sw_r_cp_api_i_WJjoDbXCE1G1Z
Adding in where I got everything for those interested:
This stuff is awesome! It's the RedLine Interior I used
Also, these, I went with the rear lights, reflectors and side lights and the darkest they had to go with my black/white motif.
Finally I got some sweet strobe vinyl decals on ebay and the classic challenger emblems for the sides.
Can't forget about the HellCat Intake Not sure if it adds much in terms of HP but it definitely gets the intake temp down on the freeway. You'll need this as well for it to connect to your headlight. FYI it's not very tight of a fit around the lip but I don't think it matters much. There's a few videos out there on how to install it, super easy, only took about 20 minutes. ( Note: you need a '15-'17 Challenger to do this)
It's an amazing mod. Outside of that - you are right in the fact the N52 is pretty well tuned from factory- worst case you can buy a new oem disa intake, but that starts getting pretty $$$. A good shop should be able to source a refurbished one. The x5's, 330s, and Z's all had the upgraded n52.
I did get 2-3 horsepower and a noticeable sound from doing a silicone intake tube as well - that was a good bang for your buck. https://www.amazon.com/Mishimoto-MMHOSE-E90-06IHBK-Engine-Silicone-2006-2013/dp/B01GA9WBB0 - I also did a clutch stop (assuming you have manual) which shortens the clutch dead space, that was $15 and is basically a plastic plug http://www.burgertuning.com/clutch_stop_BMW.html . ZHP shift knob was a nice upgrade from the plastic oem one too.
I've done pretty much every "low hanging fruit" mod on my e91, happy to share my experience. You're welcome to pm me if you have any questions
I have a 2001 Toyota Camry and I just had to replace my resonator. The part number was 17890-0311. The cheapest one I was able to find was on Amazon
I got this guy right here - https://www.amazon.com/dp/B00B90NGBK/ref=cm_sw_r_awd_TeZRub1BHQW7X
I have specific directions in a .PDF, PM me your email if you'd like them.
$427.50
Dodge Ram 5.7 Liter HEMI Cold Air Intake CAI System Mopar OEM https://www.amazon.com/dp/B01DM8QTGU/ref=cm_sw_r_sms_apa_OiMdAbJABAZFC
$304.61
2013-2017 Dodge Ram 1500 Mopar Ram Air Duct - 82214741 https://www.amazon.com/dp/B017HWLKSO/ref=cm_sw_r_sms_apa_fhMdAbR7TRMJG
I take it no engine lights? Tire pressure ok? Did you change tires or brakes recently? Any mods done (k&n filter?)?
I would say could be winter gas and tire pressure but not sure if FL gets winter gas or not and temps have not dropped that much there.
Also check for vacuum leaks, spray out the throttle body with cleaner, and clean the MAF sensor with proper MAF cleaner. I have seen k&n filters dirty the MAF sensor up and cause issues.
http://www.amazon.com/CRC-05111-Single-Use-Throttle-Cleaner/dp/B0091KCH6U/ref=sr_1_2?ie=UTF8&qid=1412006852
I purchased and installed this: https://www.amazon.com/Performance-Intake-63-9039-Lifetime-Filter/dp/B01IB1HH46/
The whole thing took me about an hour and a half to install, the instructions were better than Ikea (which aren't bad), and the entire mod is reversible if necessary.
Note: it's noticeably louder in the cabin (and outside) when you 'git after it' on the throttle. I find myself downshifting instead of honking when it's "safe" to choose.
https://www.amazon.com/gp/product/B01M1L1R3L/ref=ppx_yo_dt_b_asin_title_o00_s00?ie=UTF8&psc=1
i bought this one for my 2017 LE 2.0 cvt it sounds and looks cool is all.
they changed the shape of the MAF sensor from 2015, 16 and 17 i think from what i heard
it all depends on how you're doing it and what you already have.
for me I have a semi flex dryer hose kinda like this one. so I'll get a soft hose like [this one]
(https://www.amazon.com/Dundas-Jafine-BTD48TC-ProFlex-Transition/dp/B0015UGPWQ/ref=sr_1_2?ie=UTF8&qid=1496271613&sr=8-2&keywords=dryer+hose) and splice it in with something like this and duct tape. This will go inline and serve as the exhausting force. This is how it will mount to the printer enclosure. I haven't settled on any of these parts especially the backdraft damper as I need it to seal reasonably well, but something like this.
the other thing to consider is when to vent. for PLA you can vent the whole time which is easier. But for things like ABS you don't want to vent all the time or you'll lose the ambient heat. So you'll vent after it's done. At first I didn't think this would be an issue but after reading this and the concern with ultrafines I have to reconsider. If the fines settle while it's printing then exhausting after will only minimise the airborne stuff, but opening the box and removing the print could stir up settled pollutants. Perhaps I need an internal fan to stir up the settled fines and get them to exhaust.
This might be overkill for some people. I have pets and kids and safety is something that is important to me as I've spent a good portion of my working life dealing with potentially hazardous materials and environments.
If you have a window near your printer you could just use an AC window vent.
Here ya go.
https://www.amazon.com/Injen-EVO1800-Mitsubishi-Evolution-Induction/dp/B01KHLIY0E/ref=mp_s_a_1_3?keywords=Evo+injen+intake&qid=1571915771&sr=8-3
S&B Filters 75-5115 Cold Air Intake for 2010-2018 Toyota 4Runner / FJ Cruiser (Cotton Cleanable Filter)
Universal 4x4 Off Load Snorkel... https://www.amazon.com/dp/B07DNQKT8J?ref=ppx_pop_mob_ap_share
Priced a little high brand new one shipped is $189....
https://www.amazon.com/Injen-SP9016P-Intake-Super-Nano-Filter/dp/B00KTJOQN4/ref=sr_1_1?ie=UTF8&qid=1472835301&sr=8-1&keywords=fiesta+st+intake
http://www.amazon.com/gp/product/B00B90NGBK/ref=oh_aui_detailpage_o01_s00?ie=UTF8&psc=1
These are back in stock on Amazon
Sure, carb cleaner might work. It might not and cause more issues. Just buy this:
https://www.amazon.com/CRC-Throttle-Body-Single-Use-Twin/dp/B0091KCH6U/ref=sr_1_1?ie=UTF8&qid=1504884561&sr=8-1&keywords=throttle+body+cleaner
I actually bought a refurbished one for under $300.
https://www.amazon.com/Performance-Intake-63-9036-Lifetime-Filter/dp/B008ZE8VRC/ref=mp_s_a_1_4?ie=UTF8&qid=1539921551&sr=8-4&pi=AC_SX236_SY340_QL65&keywords=2016+tundra+k%26n+air+filter&dpPl=1&dpID=41pFhVSay8L&ref=plSrch
This one right?
http://www.amazon.com/69-3517TS-Performance-Intake-Kit/dp/B00861C6LQ/ref=sr_1_1?ie=UTF8&qid=1426106218&sr=8-1&keywords=ford+focus+cold+air+intake
is there a significant difference between a drop in and a CAI? i know my car (2012 SEL, 2 liter) wants to breath move. 30$ for a drop in K&N filter is a lot different than a 300$ CAI. https://www.amazon.com/Performance-Intake-69-3517TS-Lifetime-Non-Turbo/dp/B00861C6LQ 10 hp seems like a big gain for just a new intake. realistic, or marketing?
This was the cold air <--The page says for the ST, would this even be compatible with my SE(update: K&n website says it is)
And this is the performance
In theory i'd like whatever makes it louder, but if one is better vs another, i'd want to hear the options
It's mostly in town driving on my way to work, could be the difference. I got an airaid filter: https://www.amazon.com/dp/B007P2ESCC/ref=cm_sw_r_em_apa_VvSNBbPWB1VBS
Yeah, it's the Spectre Performance 9948 Air Intake Kit for Jeep Cherokee 4.0L. I picked it up locally from Craigslist early on after I bought my XJ, was one of the first handful of mods I did. It uses the Spectre Performance HPR9833 Air Filter. Fits over the valve cover with no issues.
I've done a cowl intake, using this kit: https://www.amazon.com/Spectre-Performance-9948-Intake-Cherokee/dp/B005M1ZBGA/ref=cm_cr_arp_d_product_top?ie=UTF8
Spectre isn't making it right now, iirc they were working on redoing it. That was several years ago, so who knows. I love this kit, got it after I was above the headlights in water and hydrolocked. I don't like the look of snorkels so this was fine for me.
i wouldnt, because if you do that less air will flow through the light. its going to travel through the path of least resistance. i'd personally use the led's in the beginning anyway.
also it looks like you'd need one of these
Try this. Sometimes leaves and other stuff gets into air intake. Should solve your problem.
https://www.amazon.com/BougeRV-Tesla-Model-Grille-Shield/dp/B07VL7H5W2/ref=mp_s_a_1_10?keywords=tesla+model+3+air&amp;qid=1566471958&amp;s=gateway&amp;sr=8-10