Best scales & balances according to redditors

Here's the method I use for weighing out powder with my Gemini-20:

1. Go through the scale's calibration process (see manual).
   
2. Allow scale to zero.
   
3. Add tray and a piece of weigh paper. This will total to approx 3 grams.
   
4. Calculate target weight based on desired dose (e.g. 2.991 + 20mg = 3.011)
   
5. Add powder until you hit target.
   
   Using this method and a set of calibration weights I confirmed my scale is usually accurate to within 1mg.
   
   Edit: Also if you add only very small amounts of powder at a time and the scale does not register it, you can touch the paper lightly with your scoop and then allow it to settle back to an accurate weight.

costco should get an amazon account:

​

https://www.amazon.com/dp/B0713XG2QP

You're going to want to weigh it on your food scale, then add the protein content to the nearest microgram for your LEAN GAINZ💪

these if you're old fashioned

You can get one on amazon for about a hundred bucks

Purchased this scale a while ago. While it may be overkill, it’s served it’s purpose well and it’s very accurate.

I got mine on amazon for $11. small (perfect for my office) and is a quick read. I don't care about timers since i use my phone. and if it craps out in a year or gets wet and shorts out - I spent $11 on it.


​

Will last you a long while

www.amazon.com/LabExact-Nitrogen-Non-absorbent-Cellulose-Weighing/dp/B00ARK0ROC/ref=sr_1_1?ie=UTF8&qid=1394293599&sr=8-1&keywords=labexact

Fold these diagonally twice so that you form a point in the middle of the paper, put it on top of the bowl, weigh powders. I can weigh all my powders directly onto this paper (by taring in between powders) and then ingest the powder off the paper. Great stuff, holds at least 6-7g total of powder.

https://www.amazon.com/gp/product/B00ARK0ROC/ref=oh_aui_detailpage_o00_s00?ie=UTF8&psc=1


i've used these in the past they're great. plus you basically get lifetime supply

Definitely MDMA or speed if you're in the college scene. 20g amphetamine paste (So around 15g dried) for $60 and you can sell that for around $100 a gram as powder or $10-$15 for 80mg in a cap.

• $27 Capsule machine and 1000 caps
  
  
• $24 Gemini 20 milligram scale
  
  
• $5 powder scoop
  
  
• $9 weighing paper
  
  So $65 for the tools to make good capsules. From here you can either spend $60 on 20g of speed paste or buy some ecstasy. If you do the 20g of paste you'll likely wind up with 15g of powder, enough to make 187 80mg speed capsules. If you sell for $10 each, that's $1,870. Minus the initial investment of around $140, you're left with at least $1,730.
  
  
  

The first answer is: search the sub, this has come up many times. But since I've had some new ideas recently I'll respond in a little more detail here:


I just ordered a mini travel bathroom scale – let's see how that works out. Just having some warning if my weight is creeping up is important. (I was actually considering a hunting/fishing scale like this because it's smaller and probably more durable, but the process of actually weighing myself on it would be ... interesting)


I also bring quality, light-weight running shoes (I like [these] (https://www.amazon.com/ON-90000-Mens-Cloud/dp/B015CR9XJ4) ) everywhere I go. I am not a runner, honestly I fucking hate running, but it's a form of cardio you can do in most places. (If you can jump rope, that would probably be even more flexible, but I lack that skill.)

I go back and forth on calisthenics, but it's at the very least a useful stopgap. I personally think the r/bodyweightfitness routine is sort of overkill – if I'm just using it as a stopgap, pull/push/stepups and leg raises are plenty for me anyway.

Weighing Scale Digital Heavy Duty HandGripped Portable for Various Use,Generic color 50Kg https://www.amazon.in/dp/B00HCEFQ4C/ref=cm_sw_r_cp_apa_i_WPY-Ab35V918F

I use this AMIR scale I picked up off Amazon for $11. It has 0.1 gram accuracy and I check it with a calibration weight one a week. It still works perfect a year later.

The simplest method is to use a spring scale like one of these:

https://www.amazon.com/dp/B00ARJOS8Y

If you know how to use an Arduino, then you can use these:

https://www.amazon.com/CHENBO-Weight-Weighing-Pressure-Arduion/dp/B078JX3KJN

I had to break this into another comment due to per comment character limits.

The following previously belonged to the above comment, but was moved here due to the above mentioned limts.

> Something you can do now: Build a filament drybox. Seriously, some filaments such as certain Nylons can go bad in just a few hours, depending on ambient humidity levels. All filaments are susceptible to moisture absorption, and ideally should be kept in something like a Spannerhands holder, even while printing, but at worst you should store them in a big plastic tub with silica gel beads to keep them dry.

> If I had to give one last tip, don't stock up on too much filament yet! Seriously! I thought I would be printing mostly in PLA but now that I've had a few weeks to work with it, I've learned I prefer PETG more, and now I have so much extra PLA! I'm sure I'll find something to do with it, but for my final tip I would add "And get a good variety!". Services like MakerBox (referral) let you try a bunch of different filaments on the cheap. It's not a ton of each filament (about 50g), but I love the variety of materials and colors.

Original second level comment begins:

Final Tips: Bonus Round!

1. Extruder Indicators are pretty cool (and USEFUL). You can get the magnets super cheap (or amazon).
   
2. Learn how to do An Atomic Pull (AKA Cold Pull), and learn it well. Do this every time you switch filaments (See "Doing it the lazy way" at the bottom of the page). You'll help remove built up deposits each time, which will help ensure a long, jam free life for you nozzle. This also skips the bleeding necessary when switching filaments (on your next "Load" you'll get a few mm of old filament and then pretty much pure new filament after that, instead of the 100mm or so of transition). You can skip doing a proper Cold Pull if you're using a brand new printer anyway. Just do a lazy pull each time you switch filaments, and then a proper Cold Pull maybe every 100 print hours, or after using extremely difficult (wet or super exotic) filaments to help remove any residue that may cause future jams or other issues. This does require undoing and redoing the idler tension again, but once you've done it a few times you can do the whole pull and filament swap in under a minute (minus hotend heatup/cooldown time). White Nylon is great for proper Cold Pulls, partially because you can crank the temp up very high (which ensures any residual filament in the hot end should also melt), White PLA would be okay for example, but may not properly pull PETG or ABS from the nozzle. White is great thanks to the color, of course, which allows you to see any residue easier; However, any color may be used. If you only ever use PLA, then PLA would be just fine for a Cold Pull. Seriously though, start by doing Cold Pulls from Day 1 and you'll easily cut out 50% of your future issues.
   
3. The small metric fasteners used in the printer are cheap. They are used in a lot of designs found online, so you should stock up (alternate source). The primary fasteners used are M3 Socket Head Cap 0.5 pitch, mostly full thread. You can also get the nuts very cheap. Square, Nyloc, and Hex. I can get the exact lengths used in the Mk3 if anyone needs them, though I'm not sure the exact grade used, it only really effects corrosion resistance.
   
4. You can also Calibrate the Extruder steps/mm and extrusion multiplier. Many people will tell you only the later is necessary but I prefer to do both anyway. Theoretically it does make a difference, but practically you can just compensate for steps/mm with the extrusion multiplier, and for all intents and purposes the result is the same, so "many people" are totally right.
   
5. You can also Calibrate the PID. You probably won't have to do this for PLA out of the box, but may find you have some temperature swings with PETG or ABS temperatures. The Official Help Article also discusses this method and how to calibrate using the LCD if you prefer. I like to keep my Mk3 settings vanilla (I've never used an M500 directly, and avoid them when I can), so I like to get my PID values manually and set them in my start GCode instead, which also allows me to setup my slicer so each switching filaments automatically switches PID profiles. The bed can be calibrated as well, but again you probably won't need to do this unless you're experiencing temperature swings more than -/+ 5°. One or two degree dips/spikes is perfectly normal (though theoretically can be tuned out, requires proper enclosure for stable ambient temps, etc).
   
   There are tons of other accessories you can get ahead of time. None of these are necessary, but are small things you might end up using (or wanting to try :P), and should help get you started getting a wishlist together. Besides the ones mentioned in this comment (and the one that precedes it) already:
   
   

• Wire Snips beat the included pliers hands down. For $4 how are you not going to pick these up right now? The cutting edge on a pair of pliers sucks and it doesn't help that it's ****ing halfway down the length of the tool. I tried to get away with just using the included tools and simply gave up trying to use the included pliers to cut zip ties. If you have Prime, get a pair of these now. Get a pair even if you don't - they're worth the shipping cost too. Thank me later.
  
• 608 bearings (for prints such as TUSH),
  
• Loctite 222 (helps prevent screws from vibrating free, not necessary thanks to Nylocs used in Mk3),
  
• A humidity sensor (for filament dry box and checking ambient),
  
• An accurate scale (for calculating remaining filament),
  
• A small fan (enhanced print cooling when needed (not very necessary except for ultra extreme bridges), enhanced circulation in filament dry box),
  
• Small bags (for silica beads),
  
• PTFE tube and matching Bowden Couplers (for something like Spannerhands),
  
• Lubit-8 (for the LMU88 bearings),
  
• SuperLube (Silicone Grease w/ PTFE for Bondtech Extruder gear maintenance),
  
• Canola Oil (for lubricating/cleaning filament and seasoning the nozzle/hotend (not necessary with modern hotends)),
  
• Small Brass Brush (also for Bondtech Extruder gear maintenance),
  
• Nozzle Reams (for the extremely rare jam, because you're doing your Atomic Pulls, right?),
  
• Extra Nozzles (no need for the kit, just an example. Hardened nozzles (black) are a good idea for composites, last longer than Brass, regardless of filament used. Prusa Mk3 comes with 0.4mm nozzle preinstalled, but you can easily swap the nozzle),
  
• E3D Hotend Sock (helps lock in heat for (theoretically?) lower current usage and more stable temperatures, also helps keep plastic off the heat block in case of print failure),
  
• Magigoo (or other adhesion aids) (for certain exotic filaments, otherwise not necessary with Mk3),
  
• Tempered Glass or Borosilicate printbeds (for certain exotic filaments),
  
• And of course, Isopropyl Alcohol (70% or better, preferably 91% or better) and Acetone, just to name a few...
  
  Edit: Upon rereading my comment I realized I have a problem.. I own every product I just listed..
  
  ^^Except ^^for ^^the ^^nozzles ^^kit ^^so ^^it's ^^not ^^that ^^big ^^of ^^a ^^problem, ^^right?... ^^Right?!

Pretty much the same one I have. Tenth gram resolution. 3000g max (good for roasting). $11 (It's 13 now, but it'll drop). Does everything I've asked of it (I no timer, but I don't want one. I have another timer on my machine). A functional bargain. https://www.amazon.com/gp/product/B01DGEWHN4/

Hanging Weight Scale | 660lb Digital Electronic Weighing Scale https://www.amazon.com/dp/B07P7Y6XF1/ref=cm_sw_r_cp_api_i_rXE2DbCX41XZH

Search reddit for volumetric dosing instructions. I use everclear with alprazolam and a chemistry scale. I really wouldn't use a Jewel scale like a Gemini 20 to measure clonazolam.

List of stuff to accurately weigh small amounts of powders:

https://www.amazon.com/x0-001g-Analytical-Balance-Precision-Electronic/dp/B07JJGM3ZL/ref=sr_1_4?crid=3OUZODGOD5UX6&keywords=analytical+balance+0.001g&qid=1574262324&sprefix=analytical+balanc%2Caps%2C500&sr=8-4

https://www.amazon.com/Plastic-Square-Weigh-Boats-Small/dp/B001AEBQW6/ref=sr_1_1?keywords=plastic+weigh+boats+small&qid=1574262373&sr=8-1

https://www.amazon.com/SuperDosing-Static-Free-Micro-Variety-Milligram/dp/B077VSD8H2/ref=sr_1_1?crid=1HOUOIAXLBU7H&keywords=microscoops&qid=1574262424&sprefix=microscoo%2Caps%2C600&sr=8-1

Cheap chemistry scales are kind of a pain in the ass to use, just leave them on for 5 minutes before using them, use the calibration weight, and keep them out of the way of air vents and stuff. It takes a bit of practice, but they're way safer to use than a Gemini 20.

I own this one, its been great!

Amazon, free shipping, total cost $10.99

AMIR Digital Kitchen Scale, 3000g 0.01oz/ 0.1g Pocket Cooking Scale, Mini Food Scale, Pro Electronic Jewelry Scale with Back-Lit LCD Display, Tare & PCS Functions, Stainless Steel, Batteries Included

https://www.amazon.com/AMIR-Electronic-Functions-Stainless-Batteries/dp/B01DGEWHN4/ref=sr_1_36?s=home-garden&ie=UTF8&qid=1520881968&sr=1-36&keywords=kitchen+scale

Something like this

https://www.amazon.com/Hanging-Hunting-Accurate-Digital-Professional/dp/B0727NHDNQ/ref=mp_s_a_1_1?ie=UTF8&qid=1537812553&sr=8-1-spons&pi=AC_SX236_SY340_FMwebp_QL65&keywords=hanging+scale&psc=1

Or this

https://www.amazon.com/Digital-Hanging-Electronic-Industrial-wirless/dp/B00PRSCS6O

Or any other hanging scale would do what you're looking for. The last one is expensive because it goes up to 2 tons

It was actually really cheap - just $10. Here it is on Amazon. I bet you the Arduino would cost more, but I had one lying around for years so I can't give you an exact cost.

I’m in the same boat. Right now I’m leaning towards:

AMIR Digital Kitchen Scale, 3000g 0.01oz/ 0.1g Pocket Cooking Scale, Mini Food Scale, Pro Electronic Jewelry Scale with Back-Lit LCD Display, Tare & PCS Functions, Stainless Steel, Batteries Included https://www.amazon.com/dp/B01DGEWHN4/ref=cm_sw_r_cp_api_i_F0UyCbJ6SPCXR

Let me know what you choose.

I already have this scale. It's pretty unstable under 10mg.. Looks like I need something like this. https://www.amazon.com/dp/B0146B55VW?tag=mcaveman-20 - thank you for your help though :)

I know I'm not being all that useful as this has no timer, but it is HIGHLY accurate, does tenths, you can disable auto-off, it takes triple A's and is very fast. Don't let the cheap price fool you it is very good indeed.

https://www.amazon.com/gp/product/B01LYYVJ71/ref=oh_aui_detailpage_o03_s01?ie=UTF8&psc=1

https://www.amazon.ca/Scientific-Triple-Balance-Capacity-Readability/dp/B008C4PABU/ref=sr_1_4?ie=UTF8&qid=1541636789&sr=8-4&keywords=triple+beam+balance+scale

Here ya go



I have no idea why the price is up to $15. I know I paid $5 and got 500...but it really is a lifetime supply (or at least 2 years for me). Best investment for powders aside from a mg scale for sure.


Cellulose based btw

I don’t see the point in using both a measuring cup and a scale when gauging your output. Generally, you either pull by oz/ml or gram. There isn’t really a need to do both on the same shot.

With that being said, I use these items depending on how I’m gauging output.

Cup: (sold at Walmart as well, but very cheap here)
https://www.kitchencollection.com/anchor-hocking-5-oz-glass-measuring-cup-91016l12?gclid=EAIaIQobChMIraz6n9af3gIVkZOzCh0xiw7xEAQYBSABEgKW6fD_BwE

Scale:
https://www.amazon.com/dp/B01LYYVJ71?ref=yo_pop_ma_swf

Both of these will not fit under even a bottomless portafilter at the same time. If you want, you can put the cup on the scale and tear it’s weight before pulling the shot, and then measure your shot output on the scale afterward and compare with the measurements on the cup.

This is the one I use: https://www.amazon.com/AMIR-Electronic-Functions-Stainless-Batteries/dp/B01DGEWHN4/

Sometimes it goes to another dollar off on sale.

Decent, has little waterproof plastic box covers. Cheap, fast.

https://www.amazon.com/gp/aw/d/B0146B55VW?psc=1&ref=yo_pop_mb_pd_title
That's what I have. More expensive but in my opinion worth it. Cheap mg scales aren't accurate to the mg.

https://www.amazon.com/gp/product/B01LYYVJ71 is what I have. Works great. You could even use rechargeable AAA batteries if you wanted to cut down on waste.

Thing is there's no way you had random super-strength speed. The treshold dose also isn't a dose you're getting any of the effects you want from. If you regularly use amphetamine (which I would guess since you described yourself as a connoisseur), the dose you need to get any of the positive effects you're going for would even be higher.

Furthermore, assuming your speed was 100% pure (which probably wasn't the case), that would still only be 73.38% amphetamine by weight, meaning that of your 5mg lines you're only containing ~3.7mg of amphetamine.

Your scale probably also isn't precise to 1mg, as that would mean you've spent 500€ to get a scale like this one, which I doubt.

That's still quite a variance. Found this one that seems to be much more accurate. Wouldn't mind spending the extra.

​

https://www.amazon.com/gp/product/B0146B55VW/ref=ox_sc_saved_title_1?smid=A20QEF2LEKCK8G&psc=1

Our shop sells fill stations, it would be best to get a bulk CO2 tank to fill from. Also a fish scale as u/phantomjm mentioned.

I think the general opinion is that using a consistent method of coffeemaking is most important. But how to achieve this?

There are several variables involved in coffeemaking, and if you're sloppy, it's hard to get consistency, or even to refine your technique once you start to get it right. So I will list a few variables and how to keep them consistent.

1. Grind. A good electric burr grinder will produce a more consistent grind, with more particles of the correct size and fewer "fines" which are basically coffee dust and undesirable. By varying the grind, the water flows through the coffee grounds at a faster or slower rate, decreasing or increasing the brewing strength.
   
   
2. Water to coffee ratio. This requires a gram scale to measure the coffee, and to measure the water as you pour it. Water is easier to measure by weight since 1g of water by weight = 1ml of volume. A cheap digital scale with .01g accuracy can be bought for about $10.
   
   
3. A good brewing device. I am fond of pourover, I use a Hario V60, but even commonly available, cheap devices like the Melita Filter Cone are acceptable. These single-cup or small batch coffee methods offer good control which allows you to make coffee in a consistent way, which helps you refine your skills easily.
   
4. Temperature control of the heated water. I have used a thermometer in a pot of water on the stove, but an electric kettle with temperature control is much easier. The temp of the water has a great effect on the quality of the brew, and inconsistent temps make it hard to home in on the brew quality you prefer.
   
   But above all, the quality of the coffee is probably the biggest effect on a good tasting brew. Always use fresh, whole beans and grind them immediately before use.
   
   Here is what I use:
   
   
5. Baratza Virtuoso grinder. A a bit more expensive than the entry level $130 Encore, but a good quality grinder. Warning: do NOT buy a refurbished Baratza grinder. You will save $30 and they will charge you $30 shipping, you could buy it new for full retail price with free shipping for the same total price.
   
   
6. Hario V60 #1 filter cone and "natural paper" filters. Amazon sells the plastic cone for $6 and 100 paper filters costs about $6.
   
   
7. Gram scale, I bought this scale for $11 but I noticed similar scales are popping up on Amazon "lightning deals" lately, for a whopping discount of $1.
   
   
8. Bonavita .7 Liter temperature controlled kettle. Hey they stopped making the smaller kettle, now it's only the 1 liter model for about $70. Oh well.
   
   So I spent about $300 total, you could get the $100 cheaper grinder and do this all for $200. And you would be a very happy coffee drinker.

Honestly, for measuring small quantities, you want a triple beam balance which measures to 0.1g resolution but at a capacity of 2.6 kilos. Otherwise just dilute and draw off an aliquot.

I believe you are talking about [stanchions] (https://www.amazon.com/US-Weight-Sentry-Stanchion-Retractable/dp/B01ITDEB2C).

I ended up buying this: Outmate Mini Digital Crane Scale 300kg/600lbs with LED(Aluminium Alloy Case) https://www.amazon.com/dp/B06X1GY9K4/ref=cm_sw_r_cp_apa_ZParzbDNGGQ3T

Idk why I didn't just buy this to begin with. Now I can weight all kinds of stuff moving forward. Lol

I got this one for my AeroPress needs. It isn’t waterproof, but it is cheap enough that if it breaks I can replace it 10 times and still be ahead of the acaia one.

3000 g x0.1g scale

That's a good question, but it's not related to the concentration of our products. You can find our current COA, NMR, and Concentration tests here.

Additionally, if you ordered powder, you can find the COA here.

If you are weighing the powder make sure you are using an accurate scale like this.

So I spent a bunch of time researching this a while back. I was considering going next-level from the gemini. The gemini is a perfectly good scale, but there are some things about it that are frustrating: mainly the very small weighing platform (weigh boat notwithstanding) and the auto shutoff.

There is a lot of weirdness out there in the mid-range scale market, which led to some FUD on my part. In particular, make sure you research the brand and make sure it is reliable. I gathered that there are a lot of knock-offs on the market that aren't great, particularly on e-bay and amazon.

For instance, I'm pretty sure that Intell-Lab scale you linked below is one of the crappy ones. Check out the reviews on it here. The Tree ones like this one are also shit.

The brands that looked good to me after doing research were A&D, Ohaus, Adam, Citizen. For whatever reason these are rarely if ever listed on amazon or e-bay, only the crappy knockoffs. I guess that's just how the market works? If you're in the us, google old will knott scales. They're a good place to look and find reviews.

The benefits of spending a few hundred on a scale are: somewhat improved accuracy (probably +/- 3 mg rather than 5), most allow you to configure auto shutoff, plugs into the wall, sturdier construction and it's easier to use weigh papers with a larger weighing platform. I much prefer that to using the gemini weigh boat personally.

Also, it's pretty freaking cool to blow on the platform and watch the numbers jump around. :)

For opsec reasons, I'd rather not to go into the scale I purchased, but I'm very happy with the investment.

> My current machine doesn't have any recipe settings

Very few do, but that's OK! All you need is a cheap scale and a stopwatch. Measure the ground espresso going in (the "dose"), then put the scale on your drip tray and set the cup on the scale (you'll see me doing that in the picture I posted of my machine). Press the button on your machine and start a stopwatch (on your phone or whatever) to set a timer.

If your machine allows for manual control, stop it somewhere before the desired final shot mass. There will be some espresso dripping out after you press stop so you'll have to learn approximately when to stop (on mine there's about 3 grams or so, so for 27g I'll stop at 24g). If your machine is fully automatic, first check to confirm that you can't control it manually, otherwise you just need to let it run until it's done and hopefully it's not a straight timer.

Finally, if the 27g shot (or whatever the recipe would call for) took too long, then adjust your grinder to a looser grind. If it ran too quickly (again, based on the recipe), then adjust your grinder for a finer grind.

This is the basic process for following an espresso recipe. Espresso is a super tweaky process and everything you do impacts the result in one way or another. Using the scale and stopwatch you can track the process against your recipe and then you can use your grinder settings to control the result.

If you are just packing the capsules full of powder, you can use a capsule filling machine. I recommend the capsule machine as I've used it to pack powdered shrooms into size 00 capsule (0.5g in each).

If you are working in smaller quantities then you'll have to fill each capsule individually with a spatula. It is time consuming, but there's something tranquil about the process. I'd put some weigh paper onto your scale and add powder with the spatula to the desired weight. Fold a crease into the weigh paper beforehand so you can use the paper to slowly drop the powder into the capsule. Repeat.

I filled about 13 size 5 capsules using creased weigh paper. The capsule machine can also help with smaller quantities by holding your capsules and minimizing spillage (put some tape over the nearby holes). Unfortunately, there are no affordable size 5 capsule machines so I had to hold them very carefully.

I got one of these cheap ones.

It works. Seems as precise as it can be, clear display, easy controls. But it's irritatingly slow. For coffee beans that's not a problem. But when pouring slow drip it's irritating. I often overshoot.