(Part 2) Best sewing pillow forms & foam according to redditors
We found 36 Reddit comments discussing the best sewing pillow forms & foam. We ranked the 29 resulting products by number of redditors who mentioned them. Here are the products ranked 21-40. You can also go back to the previous section.
Lol, I had my work laptop open and booted in the kitchen. Chart suggests around .13 lb/cuft at a shore A 90 durometer. Try this guy on amazon; https://www.amazon.com/FOAM-WORLD-Foam-Sheet-24-72/dp/B0058KFUTI/ref=sr_1_2?ie=UTF8&qid=1478134533&sr=8-2&keywords=Packaging+polyurethane+foam
Iron plates on a metal bar will never be quiet. Invest in some tight fitting bumpers.
Regardless, the vibration from the drop would be more of a concern than rattling, so you'll need to get some kind of matting. David-w-144 listed some good topics, one of which uses those thick rubber playground tiles.
You might also look into upholstery foam blocks. These will compress quite a bit, so what you might think would be a 5" block pull, will actually be a 1.5" block pull once you have some weight on there. To make up for this you could just stand on two layers of 3/4" plywood.
Not sure if this is the best deal but this is what I would look for
http://www.amazon.com/Shredded-Foam-Fill-2-5-LBs/dp/B004ZI8XCK
I would just build your own dude. All those aero cloner things are is a manifold with (x) amount of holes drilled in and (x) amount of mister heads, a decent submersible pump, a container with a lid (or manufacture a lid to fit out of Styrofoam or something similar! Bonus here is you also get inserts to stick the clones in safely) Create a manifold to fit your container. Make it a capital H shape sort of like this.In the middle of the 'H' use a Tee so you can make the connection to the pump. Tap the holes, for this application you could just find some screws with similar threading and drill/remove the manifold to tap for the misters. Connect the manifold to the pump and stick it to the bottom of the container, then fill with water (can use light nutrient solution) right up UNDER the manifold, not over it. While your pump soaks for a second, cut holes in your lid. (or cut lid to fit if using foam) Remember to make a little slot for the pump cord! Give the pump a test run AWAY FROM STUFF YOU WANNA KEEP DRY! Make sure all the misters are spraying good and not leaking (at least not too bad, no need to be mega perfect here) Then just get your clones ready! I know lots of guys that just use the insulation squares(rock wool) and just make the lid holes to fit them. I personally like the foam approach as is just feels better for me and i feel like it will give less problems with mold and other yuckies. I like to top it off with a light cabinet handle right in the middle so you can easily lift the lid (I just basically stole the handle from countless other aero cloners please dont sue me clone king lol) With this method you can make many smaller cloners or some bigger ones just dial up on the pump GPH! Just my opinion, many smaller ones might be easier to work with as youd have all the separation you need for organizing! Happy cloning bud!
J Ware Easy Filling Systems King Size https://www.amazon.com/dp/B00IAAC6SG/ref=cm_sw_r_cp_api_xKwYAbP8TV4FX
Sure, there's a couple of them, but this one seems cool. Although I can't see it to know if it is haha:
http://www.amazon.com/Pokemon-Pikachu-Transforming-Pillow-pillow/dp/B00IQJ5DDG/ref=sr_1_sc_1?ie=UTF8&qid=1458398117&sr=8-1-spell&keywords=pikachu+pillowpet
I have an arachnid soft tip board at home also. There are really two points that creat noise. First is the energy of the plastic tips hitting the plastic segment. That noise can't really be changed.
The second is the vibration after that. If I recall correctly there are two screws on the back of the board that you mount it with. I would but a 1/2 inch piece of wood to the wall then the mounting screws to that wood creating a 1/2 gap. Then place a section of 1/2 thick acoustic foam padding into that gap between the board and the wall. That's probably about as good as you will get.
https://www.amazon.com/AK-TRADING-Foam-Sheet-24/dp/B0058KFUHA
I made my own cushion. I bought some of this.https://www.amazon.com/gp/product/B00AL2J3BO/ref=oh_aui_detailpage_o08_s00?ie=UTF8&psc=1
And used the cover from another seat cushion. I traced the pattern of my car seat then cut a hole in the center so that area has no cushion. https://images-na.ssl-images-amazon.com/images/I/51rDpRBlV%2BL.jpg Similar to this, but the opening is much bigger. It's helped a lot.