Reddit reviews ABN Rubber Eraser Wheel 4in Pad & Adapter 1-Pack – Pinstripe, Adhesive Remover, Vinyl Decal, Graphics Removal Tool
We found 12 Reddit comments about ABN Rubber Eraser Wheel 4in Pad & Adapter 1-Pack – Pinstripe, Adhesive Remover, Vinyl Decal, Graphics Removal Tool. Here are the top ones, ranked by their Reddit score.
OBLITERATE DECALS: Use the ABN Rubber Eraser Wheel Adhesive Remover with Adapter 1-Pack to remove any vinyl, decal, graphic, double-sided molding tape, striping, and trim on your car, truck, or similar vehicle; 4-inch (10.2cm) diameter (larger than others!); Molded rubber medium density drill attachment tool with a stop use line; For use with electric drill with maximum 4,000 RPM (best results between 1,500 and 3,000) (Not for use on lacquer coatings and not effective on some reflective tapes)BETTER DESIGN: Solid round design is larger in size than other discs which makes this wheel fast, easy to control, plugs up less during use, and stays coolSAFE: Will not gouge or scratch acrylic enamel or urethane paint work; No need for dangerous and harmful chemicals; The wheel has a durable construction that withstands up to 4,000 RPM; The included 5/16” 24 hardware makes it compatible with any standard drillEASY TO USE: Apply light pressure starting at the top of the decal and moving side to side, or for faster results, use entire width of the wheel without tilting or angling; Remove any residue with appropriate mild solvent; Always use proper protective equipment when using power toolsCONTENTS: Package includes (1) 4-inch round decal eraser wheel and (1) 5/16” 24 thread drill adapter arbor
We used a regular hair dryer to soften the adhesive, though it was likely unnecessary since it was also hot out and kind of inconsequential to the final result.
I then flossed behind the plastic letters with fishing line (12 lb. test, for what its worth), which easily popped them off but left the thick chunky adhesive behind.
The real key here is the adhesive remover wheel you attach to a drill. I used this one: https://www.amazon.com/dp/B018WG2XYE/ref=cm_sw_em_r_mt_dp_U_Pw.wDb34TNWHK
The trick is to keep the RPMs relatively low and apply strong pressure. The adhesive will fling off easily, it's just a matter of making sure you go over each spot thoroughly.
Then I dabbed a little goo gone on a rag and wiped down the area, which revealed any further stuck on adhesive / stains. Used the drill again if need be.
The last step for me was a super quick pass with carnauba cleaner wax since there was kinda some grime around the letters that left an outline of them behind. The cleaner wax took it off with almost no effort. :)
I did all of the badges too - two on the sides, the Ram on the back, and the Promaster logo on the back. Took probably 45 minutes total, maybe less.
Okay, first, don't believe anything that the PO told you.
Before pics
Wonderwheel
There are more expensive versions of this but for 10$ it did pretty damn good
Just use low rpm (I think it says less than 2000 rpm drill) and don’t stay in the same spot for long. After wards I just brushed off the remnants and wiped away with goo gone and a towel.
I’m not like a mechanically inclined person so if I can do it you can too
Eraser wheel.
ABN Rubber Eraser Wheel 4in Pad & Adapter 1-Pack - Pinstripe, Adhesive Remover, Vinyl Decal, Graphics Removal Tool https://www.amazon.com/dp/B018WG2XYE/ref=cm_sw_r_cp_api_i_vkIKDb53F3HEB
ABN Rubber Eraser Wheel 4” Inch Pad & Adapter 1-Pack – Pinstripe, Adhesive Remover, Vinyl Decal, Graphics Removal Tool https://www.amazon.com/dp/B018WG2XYE/ref=cm_sw_r_cp_apa_b1k-BbKAHXSWA
I've had good success with these as well.
https://www.amazon.com/ABN-Pinstripe-4-inch-Sticker-Removal/dp/B018WG2XYE/ref=pd_lpo_vtph_328_bs_img_1?_encoding=UTF8&psc=1&refRID=W3892VGE3A2YFF602443
ABN Rubber Eraser Wheel 4" Inch Pad & Adapter 1-Pack - Pinstripe, Adhesive Remover, Vinyl Decal, Graphics Removal Tool https://www.amazon.com/dp/B018WG2XYE/ref=cm_sw_r_cp_tai_835kDbE8GQNEZ
This and a drill.
This thing ABN Rubber Eraser Wheel 4in Pad & Adapter 1-Pack - Pinstripe, Adhesive Remover, Vinyl Decal, Graphics Removal Tool https://www.amazon.com/dp/B018WG2XYE/ref=cm_sw_r_cp_apa_i_w3w2DbDZV2EWK
I used the same molding tape to attach as you did, to remove I used one of these rubber wheels and a drill to get the old adhesive off. You have to get the right technique of light pressure, but once you do it works perfectly.
Removing the gunk was the most tedious part of it, but once it was off and things were clean getting stuff reattached was a breeze. It's also very likely that you won't need those new fasteners and that the old ones are just popped out in a way that they can't be popped back in without twisting like you can when it's off.
Don't even mess with trying to heat and peel decals that old. Use a drill and a rubber eraser wheel. Heat guns are for amateurs that don't know any better.
https://www.amazon.com/gp/aw/d/B018WG2XYE/ref=yo_ii_pd_dx_gr_1/188-7323185-1878014?ie=UTF8&pd_rd_i=B018WG2XYE&pd_rd_r=MYRGCVXK6K2NTR47WFW0&pd_rd_w=s6OIm&pd_rd_wg=NzRRH&psc=1&refRID=PK1A5W57D0GPM348SN3F
You can thank me later.