Reddit reviews BNTECHGO 16 Gauge Silicone Wire red and Black Each 5ft Flexible 16 AWG Stranded Copper Wire

Amazon. I use BNTECHGO brand and have no complaints other than its expensive for 10 feet of wire. But I didn't find much cheaper really. Any silicone wire will do.

I use https://www.amazon.com/gp/product/B01CQJF3BS/ for ESC signal/all other low power wires on the quad. And https://www.amazon.com/gp/product/B00TG1TRL2/ for ESC power.

For my next signal wire purchase I might go up to 26 or 28 gauge. The 24 isn't too big at all but smaller would work just fine too.

Can't make it for you, but here's what you need minus a soldering iron:

https://www.amazon.com/CESS-303-3-5mm-Adapter-Cables-Connectors/dp/B01G0NF9CY

https://www.amazon.com/BNTECHGO-Silicone-Flexible-Strands-Stranded/dp/B00TG1TRL2

https://www.amazon.com/25ft-Expandable-Braided-Sleeving-BlackRed/dp/B071WF5K2X

https://www.amazon.com/130-pcs-Adhesive-Assortment-MILAPEAK/dp/B075NBCDPQ/

I would opt for a nice low resistance silicone wire something like this: http://www.amazon.com/BNTECHGO-Gauge-Silicone-Wire-Feet/dp/B00TG1TRL2/ref=sr_1_1?ie=UTF8&qid=1452174862&sr=8-1&keywords=16awg+silicone+wire


the trick on the ICS that im currently trying to figure out where to put the mosfet with rear wiring the gun i dont want to impede on buffer tube battery space, and really the nice wire channels that they make will not hold both the battery leads and the trigger wires for the mosfet. Also We use hand made mosfet's with a self resetting fuse

i've had this problem many times.

its almost certainly that your wires are making intermittent contact. i've had to replace my bed sensor wiring and power wiring about 4 times.

once however my actual temp sensor cracked in half and i had to replace it with a 100k thermistor.

https://www.amazon.com/Gikfun-Thermistor-Temperature-Sensor-Printer/dp/B018QL5LPI/ref=sr_1_4?ie=UTF8&qid=1481397650&sr=8-4&keywords=100k+thermistor
here are the thermistors and as for the wiring, if thats what it turns out to be(most likely is)

sensor wiring
https://www.amazon.com/gp/product/B01708AYYQ/ref=oh_aui_detailpage_o05_s00?ie=UTF8&psc=1

power wiring
https://www.amazon.com/gp/product/B00TG1TRL2/ref=oh_aui_detailpage_o05_s00?ie=UTF8&psc=1

i also recommend using https://www.amazon.com/Wago-222-412-LEVER-NUTS-Conductor-Connectors/dp/B00HIOP6SC/ref=sr_1_5?ie=UTF8&qid=1481397789&sr=8-5&keywords=wago+connector

for the wiring inside the unit, so that your wiring can be replaced easily without buying a new wiring harness.

so i'm looking at buying these bulbs, these connectors and this wire. altogether it'll be around $20, but i'll only need some of this stuff for each.

i'm trying to decide if it is worth buying the extra connectors and wire or if i should just buy this pair of connectors with wire already soldered on and the bulbs and save myself $10.

I believe I found the wires needed, but it would be awesome if someone checked, just to be sure!

​

Also, are the yellow wires the same as the others? I can't find markings on mine.

For wire I'd buy something like this:

https://www.amazon.com/BNTECHGO-Gauge-Silicone-Wire-Black/dp/B00TG1TRL2

You probably don't need 16 gauge but it doesn't hurt and it's only $5

You can solder right? I'm assuming you can solder... otherwise this is much more difficult and more expensive as you'll need to find the right adapters.