Reddit reviews Dshot12 Port UTP 10 inch Cat5e Network Wall Mount Surface Patch Panel
We found 5 Reddit comments about Dshot12 Port UTP 10 inch Cat5e Network Wall Mount Surface Patch Panel. Here are the top ones, ranked by their Reddit score.
Solid and reliable terminations for copper cabling featuring a minimum of 3 mm 50 micro-Inch gold plated jack contactsCompatible with both 110 and Krone punch down toolsSupports 22 to 26 AWG stranded and solid wireFor use with unshielded twisted pair (UTP) Cat5e network cableCat5e performance is in compliance with the ANSI/TIA/EIA 568 B.2 standard
I can't tell for sure from the photos, but that cable is probably at least CAT5e or better, which is just fine for 1GB ethernet in the house.
You need to cut off the phone jacks and install CAT5e or better RJ-45 jacks with a punch down tool. Do this conversion at every place where you want network. Then in the basement you need to punch down the other end of each cable separately to a CAT5e or better patch panel. Then you need to run short CAT5e or better patch cords from the patch panel to an Ethernet switch. Finally you need to connect your router to the switch, either directly, or through one of the network jacks you installed in the house.
All you need is a (cheap) punch down tool and some sort of a patch panel. It's really not that hard. If you have to pull any insulation back you might want to use a stripper. But you can probably just get away with small dykes. Just try and keep the twist as close to the punch down as you can---but it doesn't have to be perfect to work.
Also, there are two wiring standards 568A and 568B. They have to match on each end so you might want to pull one of your wall jacks to see how it is wired. Just Google for a wiring diagram to see the difference. Or your jack and panel might actually have both color coded on them and you can see which way they did the jacks.
I aways have used the B standard. IIRC the A standard provided backward compatibility with old AT&T standards. But if your jacks are A I would not change them to B.
Cat5e should be plenty fast for home use.
Like the other guy said, you really need to get power here and a switch. If you want to do it right, you could terminate all the wiring into a patch panel, then attach those ports to your switch. That gives you a nice setup to centralize network equipment.
Examples:
Patch: https://www.amazon.com/Dshot12-Cat5e-network-Mount-Surface/dp/B00NTWK8VW/ref=mp_s_a_1_8?keywords=patch+panel&qid=1572791966&sprefix=Patch+&sr=8-8
Switch:
https://www.amazon.com/TP-Link-TL-SG1008D-Unmanaged-Gigabit-Network/dp/B001EVGIYG/ref=mp_s_a_1_6?keywords=8+port+gigabit+switch&qid=1572792046&sprefix=8+po&sr=8-6
Edit:
Thinking more, if you absolutely can't get power in there you could probably do a PoE (power over ethernet) powered switch here, with a PoE power injector on another line.
Something like this in the closet: https://www.newegg.com/p/N82E16833122614
Then the port on there for power would need to lead to something like this in another room: https://www.amazon.com/TP-LINK-TL-PoE150S-Injector-Adapter-Compliant/dp/B001PS9E5I/ref=mp_s_a_1_3?keywords=poe+injector&qid=1572793212&sprefix=poe+i&sr=8-3
Each cable is for each room would this work You need to cut off the phone jacks and install CAT5e or better RJ-45 jacks with a punch down tool. Do this conversion at every place where you want network. Then in the basement you need to punch down the other end of each cable separately to a CAT5e or better patch panel. Then you need to run short CAT5e or better patch cords from the patch panel to an Ethernet switch. Finally you need to connect your router to the switch, either directly, or through one of the network jacks you installed in the house.
Do you have a picture of the point in your basement where all the Cat5 wires come together?
There should be at least a panel there something that looks like this https://www.amazon.com/Dshot12-Cat5e-network-Mount-Surface/dp/B00NTWK8VW/ref=sr_1_3?keywords=cat5+panel&qid=1550268373&s=gateway&sr=8-3 where all the ethernet cables connect to.
From the front of the panel there might be a bunch of wires that connect to a box (which will be a switch, or possibly a router). Probably not the switch and you'll have to acquire one. Once you have a switch then you'll be able to get the ethernet cables working.
Once you have done that, get an access point with an ethernet connection and use that in one of the rooms near your wife's office. that should give her the best connection. What would be better is to use ethernet to connect her device. That's the right way to do it if you can.