Reddit reviews EG STARTS Zero Delay USB Encoder to PC Games Arcade Stick Controller for 2Pin Joystick Happ Push Buttons Wire
We found 5 Reddit comments about EG STARTS Zero Delay USB Encoder to PC Games Arcade Stick Controller for 2Pin Joystick Happ Push Buttons Wire. Here are the top ones, ranked by their Reddit score.
Zero Delay Arcade USB Encoder For Your Pc Game DIY!Perfect fit for HAPP type push button and joystickAll Joystick and Push Button types which with 4.8mm Terminal!Use this Encoder you can build your own Arcade Game Machine!Plug and Play, It does not require any drivers. All windows systems! Such as Windows XP,Windows 7,Windows 8 etc!
I used this. It's a game controller but I use software to emulate keystrokes.
Zero Delay USB Encoder To PC Controller 2Pin Joystick Cable + Happ Pusb Buttons Cables For Arcade Happ DIY Kits Parts Mame Games https://www.amazon.com/dp/B01L8K21CK/ref=cm_sw_r_cp_api_EBGLzb1W3F694
https://youtu.be/UsSUUdw4bTY this one is just a simple button box.
EG Starts Zero Delay USB Encoder To PC Controller 2Pin Joystick Cable + Happ Pusb Buttons Cables For Arcade Happ DIY Kits Parts Mame Games https://www.amazon.com/dp/B01L8K21CK/ref=cm_sw_r_cp_apa_hybJAbPT1XXMZ this is the board used. If you wanted to do rotary encoders you'll have to use Arduino, but there are instructions for that on the same YouTube channel.
Forgive me for repeating anything you may already know.
For the buttons and joystick, you need a USB encoder. This or similar:
https://www.amazon.com/EG-STARTS-Encoder-Controller-Joystick/dp/B01L8K21CK/ref=sr_1_5?keywords=arcade+usb+encoder&qid=1574973074&sr=8-5
Connect the buttons and joystick to the encoder, connect the encoder to the pi through USB. When you set up retropie, you will be prompted to assign each button for the pi interface.
For the GRS spinner and trackball, you will also need the GRS "12-in1 board".
https://www.amazon.com/Arcade1Up-12-1-Interface-Board/dp/B07NKJ3SKH/ref=sr_1_2?keywords=grs+12-in-1&qid=1574973218&sr=8-2
The GRS spinner and trackball are both designed to plug directly into the stock Arcade1Up hardware. There is no USB connection on those devices. The 12-in-1 board gives you that USB connection. Plug the Spinner into the "P1" port on the 12-in-1 board. Plug the Trackball into the "P2 port". Use the micro USB port on the board to connect to a USB port on the pi.
The pi will recognize the spinner and trackball as a mouse - both devices will be interpreted as the same mouse input. But, that should already be set up to control left/right/up/down movements in any emulator. (Left/right only for the spinner, of course). So, you can jump right into centipede, or tempest or whatever you're using them for.
You may need to adjust the sensitivity of the trackball and/or spinner in each game individually until you get the right performance. There are threads about that on this sub. Here's one:
https://www.reddit.com/r/Arcade1Up/comments/cj1m4b/share_your_trackball_speed_settings_in_retropie/
In that thread, you can ignore where it says to change the speed. As is clarified later in the thread, the speed settings don't matter - only sensitivity.
Not really going to any tournaments regularly- I actually hadn't even thought about that! Although I am aware that that is a concern among hitboxes.
Internals all I'm using is EG STARTS Zero Delay USB Encoder. https://www.amazon.com/dp/B01L8K21CK/ref=cm_sw_r_cp_apa_i_HajZDbTGTFR3P
And the buttons (which I linked elsewhere here).
Again nothing I paid a lot for, this is just me having fun and really liking the hitbox layout.
Sorry, I was just trying to find this and being lazy. 😀
EG STARTS Zero Delay USB Encoder to PC Games Arcade Stick Controller for 2Pin Joystick Happ Push Buttons Wire https://www.amazon.com/dp/B01L8K21CK/ref=cm_sw_r_cp_apa_i_TvV1CbSF4J7SR
Which I can hook more quality (non lit) buttons too.