Reddit reviews Leviton 515PR 15 Amp 125 Volt, Straight Blade Rubber Plug, NEMA 5-15P, Black
We found 12 Reddit comments about Leviton 515PR 15 Amp 125 Volt, Straight Blade Rubber Plug, NEMA 5-15P, Black. Here are the top ones, ranked by their Reddit score.
Item Weight: 0.14 lbCountry of Origin: ChinaColor: BlackBrand name: Leviton
Just cut the cord at the damaged spot, wire in a new plug and plug in to an extension chord to make up for the lost chord length. Probably your safest bet.
It's super easy, you need a replacement plug not unlike this one, wire cutters, and wire strippers; and wire the plug according to this diagram.
If you can't replace the whole cord, then get a polarized replacement plug like this: http://smile.amazon.com/Leviton-000-515PR-000-Black-Rubber-Grounded/dp/B000FKBZ7M/ref=pd_bxgy_60_img_3?ie=UTF8&refRID=00CKYASEEQZXHD5FPJST
You cut off the damaged plug, strip the insulation back, strip the inner wires, and connect to that with screw terminals.
Just replace the plug on the PDU with a replacement plug. The worst thing that would happen is the house's circuit breaker pops if you try to pull more than 15 amps on the circuit. The 15 amp plug also works in a 20amp outlet. Its pretty much a win-win for your situation. This is what I did when I got a UPS that had a 20amp plug, but I only had 15amp sockets at the time.
The writing on the wire is the maximum rating of the wire. Parts of Europe use 240 v as the standard mains voltage while North America and other places use 120 v. The heater was made with the 300 v cable as it could then ship anywhere and the manufacturer put the plug on at the last minute once they knew where it was going to be shipped.
The standard is 120 volts average, but the actual voltage out of the wall varies a little bit. The plug is rated to 125 volts so it doesn't burn out when the voltage drifts a little above 120 v. There are additional safety factors on top the 125 v rating as well.
A 125 volt plug is fine. Just make sure the plug can handle the wattage of the heater. Your heater is a 1500 w device, which is on the upper end of what you will find for a residential device and not all replacement plugs are rated the 1500 watts. Any 125 v 15 amp plug with a ground will work.
This is first listing on amazon. There are bajillion places to get them though.
https://www.amazon.com/Leviton-515PR-Straight-Blade-Rubber/dp/B000FKBZ7M/ref=sr_1_5?ie=UTF8&qid=1550644370&sr=8-5&keywords=replacement+electrical+plug
I've only been in the trade for 7 months so to be honest I'm not exactly sure. I think you'd need to find out how many amps each light draws, and if it's more than 15 combined then you might wanna start decreasing the number of lights until it's under 15amps, this is the standard ampacity of household receptacles. You might be able to get away with a little over but like I said I don't know a huge amount about this exact application. More people will comment soon with a much better understanding of the concept. Here's a link for a plug head on Amazon, currently on sale. Leviton 515PR 15 Amp 125 Volt, Straight Blade Rubber Plug, NEMA 5-15P, Black https://www.amazon.com/dp/B000FKBZ7M/ref=cm_sw_r_cp_api_i_b8o5AbHV9APYF
It's a 5 minute job to replace the plug. Cut off the old one, as close as possible to the plug, strip the rubber back, strip the three individual wires, and wire put them in the replacement plug (something like this would do fine).
The replacement plug should tell you exactly how long to make your cuts and strips.
You should be able to buy plugs like that at any home repair/hardware store.
https://www.amazon.com/dp/B000FKBZ7M/ That's all you need to fix it. Well, maybe some soldering.
You should replace the plug with a round one like this https://smile.amazon.com/Leviton-515PR-Straight-Blade-Rubber/dp/B000FKBZ7M/ and embed it into the print.
Stock advice if you are uncomfortable with an electrical issue is to find someone who is comfortable with it, or hire an electrician.
That said, what you can do depends on how the current wires are attached. Since you didn't provide pictures, I'm guessing. Do not splice the old plug and wire onto the end of the new wire. Not a good idea at all. If the new wire on the dishwasher is attached in such a way that the wires can be unscrewed and removed within the wire box on the back of the machine then you can take the wire off and replace it with a wire that has a plug on it. But a better option may just be to add a plug to the end of the wire that came on the machine. Hardware stores, Home Depot. or the internet sell replacement plugs to use.
https://www.amazon.com/Leviton-515PR-Straight-Blade-Rubber/dp/B000FKBZ7M/ref=pd_lpo_vtph_60_lp_t_3?_encoding=UTF8&psc=1&refRID=NHZRWY0Q3M54Z7BZ5Q9D&dpID=41wZ0pkqgaL&preST=_SY300_QL70_&dpSrc=detail
Replacement plug
If it's towards the plug, you can buy a replacement plug at a hardware store (like this) and simply cut the cord / wire up the replacement. (They open and have a screw terminal for each wire.)
Otherwise if the cord would be too short, the proper way is to replace the whole works.
I worry about splicing / using electrical tape because one tug and the cord could separate. But if you tape the hell out of it, it would probably hold up.