Reddit Reddit reviews Maxmoral 1-Pack Dual Fan Mount Rack PCI Slot Bracket for Video Card DIY Support 9cm/12cm Fan Computer Radiator Holder

We found 6 Reddit comments about Maxmoral 1-Pack Dual Fan Mount Rack PCI Slot Bracket for Video Card DIY Support 9cm/12cm Fan Computer Radiator Holder. Here are the top ones, ranked by their Reddit score.

Electronics
Computers & Accessories
Computer Case Fans
Computer Components
Internal Fans & Cooling Components
Computer Internal Components
Maxmoral 1-Pack Dual Fan Mount Rack PCI Slot Bracket for Video Card DIY Support 9cm/12cm Fan Computer Radiator Holder
Type: 1 Set PCI Slot Fan Mount Bracket, Simple design, easy operation, come with matched fixing screw fasteners, convenient to install.Made of high quality metal material with fine workmanship, black stoving varnish surface, beautiful appearance, rust and corrosion resistance, durable to use.Supply with 1 PCI slot brace and 2 fan connectors, used to mount dual PC cooling fan in one PCI slot bracket.Effectively improve the system heat dissipation effect, reduce PC case noise, for more powerful performance.Fit for 9cm, 12cm fan, good compatibility with most of graphics cards. Practical fan accessories for computer project DIY.
Check price on Amazon

6 Reddit comments about Maxmoral 1-Pack Dual Fan Mount Rack PCI Slot Bracket for Video Card DIY Support 9cm/12cm Fan Computer Radiator Holder:

u/bgunn925 · 6 pointsr/buildapcsales

Here is a pic of my rig with this bracket. Even under full load at ~2075MHz, the fans on my 1080 Strix never hit 60%.

u/Visonik · 2 pointsr/Corsair

I used a PCI slot bracket for the fans i found on amazon. Link Below. I did have to modify it for this case just a little bit. Was easy though, used a hack saw to shave off what i needed. Very simple. Came out great and the GPU stays extra cool.

(Click Here )

u/ChefJoe98136 · 2 pointsr/DataHoarder

FWIW, it totally depends on how budget sensitive you are. Based on the hardware you're talking about, it sounds like budget matters quite a bit.

In the USA, you can pick up a Dell H200 or H310 PERC card for ~$30, get the appropriate SAS to 4 SATA breakout cables for under $10 each, and flash the card into IT mode. If you want to get fancy, you can point a fan at the chipset heatsink to account for lower airflow in most cases in that area (I used a PCI slot cover-type fan adapter slow shipped from china and a single 92mm fan I had around). It's an extremely popular way to get a few more ports into your datahorder build and the card is well supported by most software. I operate it in pass-through, so I have no idea if you should use it for RAID or not.

https://www.ebay.com/itm/47MCV-047MCV-342-0663-DELL-PERC-H200-6Gb-s-PCI-e-SAS-SATA-Raid-Controller/253307058926

https://www.ebay.com/itm/Dell-PERC-H310-8-Port-6Gb-s-SAS-Adapter-RAID-Controller-HV52W-Replaces-Perc-H200/192120843762

https://techmattr.wordpress.com/2016/04/11/updated-sas-hba-crossflashing-or-flashing-to-it-mode-dell-perc-h200-and-h310/

https://tylermade.net/2017/06/27/how-to-crossflash-perc-h310-to-it-mode-lsi-9211-8i-firmware-hba-for-freenas-unraid/

https://www.amazon.com/CableCreation-SFF-8087-Female-Controller-Backplane/dp/B013G4EOEY/

https://www.amazon.com/dp/B07N3T1GJP

u/Petti-The-Yeti · 2 pointsr/Amd

I'm currently looking at the G12 bracket, and IMO, there's plenty of Dremel-y potential there. Trim off the front lip and the little fan cooler to the side of the water block mount, thermal tape some little heatsinks to the VRM/RAM/whatever, and use a PCI slot dual fan bracket below the card, pointed at the heatsinks and PCB to cool everything else.

It's a DIY hybrid cooler. Hell, if you have a 3D printer, you could even make a proper shroud for it...

I already have a Corsair H50 lying around in a parts box... I might just do some redneck engineering this weekend on my 5700XT.

u/ZeroDigit · 1 pointr/pcmasterrace

PCI Slot fans like this : https://www.amazon.com/Maxmoral-Bracket-Support-Computer-Radiator/dp/B07N3T1GJP/ref=sr_1_1_sspa?keywords=pci+fan+mount&qid=1557333025&s=electronics&sr=1-1-spons&psc=1

​

I will be mounting my own 120mm x2 with the fans blowing up towards the card ( the fans are pointing down like standard open air GPU's )

Do they really work ? I am wondering if putting it a way to blow towards my Gigabyte RTX 2080 Windforce edition would help the air move a little better to cool my card just a bit more. Thoughts ?