Reddit reviews TOGGLER SNAPTOGGLE BB Toggle Anchor, Zinc-Plated Steel Channel, Made in US, 3/8" to 3-5/8" Grip Range, For 1/4"-20 UNC Fastener Size (Pack of 50)
We found 5 Reddit comments about TOGGLER SNAPTOGGLE BB Toggle Anchor, Zinc-Plated Steel Channel, Made in US, 3/8" to 3-5/8" Grip Range, For 1/4"-20 UNC Fastener Size (Pack of 50). Here are the top ones, ranked by their Reddit score.
Toggle anchor installs behind 3/8"- to 3-5/8"-thick hollow materials including gypsum board, drywall, and concrete block to provide a secure hold from within the mounting materialAnchor affixes to the wall before adding the bolt and fixture, allowing one-person installation and fixture changesMade in USA, and works with 1/4"-20 UNC-threaded metal bolts (sold separately)Ultimate tensile strength is 265 lb. in 1/2" drywall and 1,080 lb. in concrete block with a 1/4"-20 UNC boltUse one-fourth or less of listed maximum values for safe working loads (as required by local regulations)
My home was built in 1898 and I've got a tv hanging on the wall with no problem.
You have to use plaster wall toggle anchors, not those plastic ones they sell at ikea.
for the television I tediously searched for studs, they do exist in there, and attached a thick piece of plywood to them. Then I screwed the tv mount to the plywood. Been holding strong for 5+ years.
We use these to hang TV and speaker mounts (obviously one side in a stud). The bolt can be unscrewed and re-inserted without losing the end in the wall which is nice. I'm not sure if these can fit with your mounting bracket for the mirror though.
TOGGLER SNAPTOGGLE https://www.amazon.com/dp/B0051IARUE/ref=cm_sw_r_cp_apa_i_bHowDbY7PZCQ3
AV installer here. A single stud is just fine for a tilt mount it will hold the weight and then some. And frankly you don’t need the 4 additional bolts. Bolts a drywall don’t mix you need drywall toggles and one on each side. The toggles are simply keeping the mount from rotating the strength is on the stud.
These are what I’m talking about:
https://www.amazon.com/TOGGLER-SNAPTOGGLE-Zinc-Plated-Channel-Fastener/dp/B0051IARUE/ref=asc_df_B0051IARUE/?tag=hyprod-20&linkCode=df0&hvadid=312360540451&hvpos=1o2&hvnetw=g&hvrand=10502080946968211216&hvpone=&hvptwo=&hvqmt=&hvdev=m&hvdvcmdl=&hvlocint=&hvlocphy=9060467&hvtargid=pla-641936376392&psc=1
These might work TOGGLER SNAPTOGGLE BB Toggle Anchor, Zinc-Plated Steel Channel, Made in US, 3/8" to 3-5/8" Grip Range, For 1/4"-20 UNC Fastener Size (Pack of 50) https://smile.amazon.com/dp/B0051IARUE/ref=cm_sw_r_cp_apa_i_0Z2IDbA64HQE7
Plaster also has lath behind it which was used as something for the plaster to grab onto. Thin pieces of wood that span the studs. If you use the zip anchors I posted above then they would grab the lath from behind using the wood as an anchor.
Tough call though cause if you somehow don't hit the lath your plaster is going to pull right out in a big chunk when you mount the object.
I've had a lot of luck with these: http://www.amazon.com/TOGGLER-SNAPTOGGLE-Toggle-Bolt-Fastener/dp/B0051IARUE
My tv hangs from 4 of them. Crazy strong.