Reddit reviews Tripp Lite 12U Wall Mount Rack Enclosure Server Cabinet, Hinged, 20.5" Deep, Switch-Depth (SRW12US)
We found 12 Reddit comments about Tripp Lite 12U Wall Mount Rack Enclosure Server Cabinet, Hinged, 20.5" Deep, Switch-Depth (SRW12US). Here are the top ones, ranked by their Reddit score.
Unit Dimensions: 23.63" W x 21.6" D x 25" H | Weight: 60 lbsWall-mount cabinet secures and organizes 12U of 19-inch rack equipment up to 20.5 inches deep in locations with limited floor spaceMaximum load Capacity of 200 poundsSwings away from wall on hinge for Easy back door accessMounts to wall or rolls on floor(with optional Srcaster)Ships fully assembled
http://www.amazon.com/gp/aw/d/B001TGUYI2/ref=mp_s_a_1_2?qid=1450103490&sr=8-2&pi=SY200_QL40&keywords=12u+hinged&dpPl=1&dpID=51jr8xTQxLL&ref=plSrch
https://www.amazon.com/gp/product/B001TGUYI2/ref=ppx_yo_dt_b_asin_title_o08_s00?ie=UTF8&psc=1
I use a ton of these at work.
https://www.amazon.com/dp/B001TGUYI2/
Not sure how much space you need, but they're great.
lock it in a rack enclosure?
http://www.amazon.com/Tripp-Lite-SRW12US-Enclosure-Cabinet/dp/B001TGUYI2/ref=sr_1_13?ie=UTF8&qid=1462809462&sr=8-13&keywords=enclosed+rack
https://www.amazon.com/gp/product/B001TGUYI2/ref=ppx_yo_dt_b_asin_title_o03_s00?ie=UTF8&psc=1
Data centers? You don't have to be a data center to need a rack. Just to give you an idea of where I'm coming from: I'm setting up an office for 5 people with a small rack which will hold two servers, a UPS, a RAID, and some phone gear - in addition to the POE switch for the cameras and VOIP phones.
All told, about $3k - 5k worth of gear. Putting in cameras that can be defeated by unplugging them from a power outlet is half-assed, unless you just want something to keep an eye on your pets or children.
Your plan sounds mostly reasonable. A few suggestions though.
​
Try and move your central termination point/patch panel to somewhere inside the house. The high temperature and humidity (ie condensation) in a garage don't often play nice with electronics.
​
For the ISP connection, I would just extend a cable (preferably both RG-6 coax and cat6 for future uses) outside to their demarc and run it back to your main wiring hub. Your solution would work, but might as well run it back if you are putting in the work.
​
Run some more cables to ceiling locations for you to put POE wifi access points.
​
Don't have two switches, just have a single switch with some POE ports. That interconnect between the two switches will become a bottleneck if you have any significant amount of intra-house traffic.
​
Ubiquity is not overkill for your setup, but I would be hesitant to put gear in that price range in the garage. If you cannot get out of the garage, you might want to make sure to use gear that you can afford to replace when it breaks.
​
When you say " head-height cabinet ", I assume you mean a proper 4 post enclosed server rack, something like: https://www.amazon.com/Tripp-Lite-Enclosure-Switch-Depth-SRW12US/dp/B001TGUYI2. If you meant kitchen cabinet, don't do that :P
​
If you have the walls open, run 2-4 times more cables than you think you need to each wall face plate. Also, look into using conduit, so you can easily pull new cables through in the future. If cost becomes an issue, you can run the cables outside the conduit and run empty conduit for future use. If anything happens with the old cables, just abandon them in the walls.
​
Run RG-6 coax, fiber, speaker wire, or any other low voltage cabling you can think of while the walls are open as well.
I only see two items that are actually rack mountable. One thing to consider is a vertical wall mount bracket for the Netgear switch and patch panel. These brackets can be used horizontally as well, so you could even mount them to the bottom of one of the existing wooden shelves. Once the switch is taken care of, everything else can be mounted in a much shallower space.
If you want an enclosed wall mount cabinet, the Tripp Lite SRW12US and
Tripp Lite SRW10US both support a mounting depth of up to 20.5". If you go this route, make sure the antennas on the wireless APs are located where their signal isn't blocked.
For about $100, you can get the Tripp Lite SRWO8U22 2-post open frame "cabinet," or the Kendall Howard 2-post 8U rack. Both support up to 18" mounting depth.
The StarTech RK12OD desktop 2-post rack for $46.99 is an interesting alternative to normal racks. Due to the slope, you want to be sure any equipment on a cantilevered shelf is somehow prevented from sliding off. Just set the DS1813+ at the bottom, between the posts.
With any rack/cabinet, you're probably still going to need a couple of cantilever shelves to hold the non-rack mountable equipment. With an enclosed cabinet, you can use the bottom and top as shelves. You could even cheat and put some of the lighter items on the Netgear switch.
Also, be careful how you stack the equipment that wasn't designed to be rack mounted. A lot of it will vent the heat up instead of out the back.
Until you put an air duct in the closet itself, I doubt there will be much circulation in there. Be careful about putting all of the equipment up high because all of the hot air will be more or less trapped above the door louvers.
There are vents and mounting holes for fans - 2 on top and 2 on bottom.
Here’s the rack
Couldn’t find any good small options locally. So I didn’t get any Craigslist’s steals.
These fans I’ve read good comments on cfm to noise ratio
Noctua Fan with Focused Flow and SSO2 Bearing, Retail Cooling NF-F12 iPPC 3000 PWM
We have used 1/2 and 1/4 size wall mount racks for tight areas.
https://www.amazon.com/Tripp-Lite-Enclosure-Switch-Depth-SRW12US/dp/B001TGUYI2
No it's this Tripp Lite 12U Wall Mount Rack Enclosure Server Cabinet, Hinged, 20.5" Deep, Switch-... https://www.amazon.com/dp/B001TGUYI2/ref=cm_sw_r_sms_c_api_DrhhAb1VR434Z
https://www.amazon.ca/Tripp-SRW12US-Enclosure-Server-Cabinet/dp/B001TGUYI2
https://www.amazon.com/Kenuco-Steel-Vertical-Mountable-Server/dp/B01N5YH1ZE