Best plier sets according to redditors
We found 88 Reddit comments discussing the best plier sets. We ranked the 35 resulting products by number of redditors who mentioned them. Here are the top 20.
We found 88 Reddit comments discussing the best plier sets. We ranked the 35 resulting products by number of redditors who mentioned them. Here are the top 20.
It's not melted, it's just plastic deformation. The clamps are putting a ton of pressure on the hose and the hose is deforming as a result. It's entirely normal.
You should be able to wrassle it out with those pliers but they also make special pliers for those type of clamps. https://www.amazon.com/Drake-Off-Road-4502-Pliers/dp/B000I1KJT8
Those are hose clamp pliers for those spring steel hose clamps I love to hate.
Knipex are amazing. I borrowed them constantly for like a week and bought this set and recommend them to everyone.
I highly recommend the
Hakko 936 soldering ironHakko 888 soldering iron, which is still actually available. It's hard to fathom how a $100 soldering iron could be that much better than a $20 one, but once you start doing anything more serious than just sticking some wires together, it's worth it.As for other tools,
As for components, I've been buying them piece-meal for years, so other's will probably be able to yield you a better recommendation for kits than anything I can find just from a quick search. I do mostly digital work, so as far as passives, my main stock is:
If I need any other resistor for a specific project, I'll tend to just buy an extra 10 and keep them in labeled coin envelopes.
Random other pieces:
Edit: Fixed the soldering iron model.
Disclaimer: I'm using my Amazon Associate links for all of these, which always feel a little amoral and a conflict of interest, but really, if my apartment were to go up in flames and I could afford it, I'd buy every link on this list right now. Does anyone have strong opinions one way or the other on using them?
Knipex 002006S1 3-Piece Cobra Pliers Set (7-Inch, 10-Inch, & 12-Inch) https://www.amazon.com/dp/B000X4KNTG/ref=cm_sw_r_cp_apap_O5HerMerjQW2o
Tools are good. Don't know what he needs but these are the best pliers out there.
My Knipex plier set.
Here's what I would personally recommend for a decent minimum starter set, assuming you're just looking for general homeowner/handywork tools:
Those are all solid quality tools that I've personally used in the past. There's obviously tons of other stuff you'll need along the way if you're into fixing things but that's a great starting point.
these are pliers you seek my friend
You gotta upgrade them grips
https://www.amazon.com/Klein-Tools-89-Replacement-Tools-Koat/dp/B00093D7AI
With some hose clamp pliers those are never a problem
Knipex Tools 9K 00 80 94 US Cobra Combination Cutter and Needle Nose Pliers Set (4 Piece) https://www.amazon.com/dp/B00KBCM456/ref=cm_sw_r_cp_apa_fe8KAbMFWEJRA
This would meet my needs, what do you think?
EDIT: what do you guys think of gearwrench pliers?
GearWrench 82108 7 Piece Standard Pliers Master set https://www.amazon.com/dp/B0014ZXY80/ref=cm_sw_r_cp_apa_th8KAbG67W1CQ
+1 for knipex pliers. I bought this three pack and they're easily my most used pliers.
KNIPEX Tools 00 20 06 US1, Cobra Pliers 7, 10, and 12-Inch Set, 3-Piece https://www.amazon.com/dp/B000X4KNTG/ref=cm_sw_r_cp_api_i_dyOQCbTNQCQSZ
I too was in your position just a few years back. Here is a list of my recommendations for the entry-level versions of the items you listed above as well as some other things I like to have handy.
Now for my personal suggestions;
I hope this list helps and I wish you well on your journey in beginning Bladesmithing!
Yeah, no. The entire list of SnapOn pliers is hilariously overpriced. Even compared to Knipex.
$70 for a 5" needle nose? You can easily have a 3 pc set of Knipex for $70. Comfort handles too.
https://www.amazon.com/Knipex-00-20-11-Assembly/dp/B001094GLY/ref=mp_s_a_1_32?ie=UTF8&qid=1543323640&sr=8-32&pi=AC_SX236_SY340_QL65&keywords=knipex&dpPl=1&dpID=41rZKY7XMRL&ref=plSrch
Or $45-$50 if you go to Amazon.de
SO charges $65 for side cutters. I could get a 9" and 6" Knipex for $65.
do yourself a favor and get a nice pair of flexible hose clamp pliers
Barring that, even just regular hose clamp pliers are miles ahead of using whatever random pliers are laying in your toolbox.
Those are Cobra pliers. Most people buy Cobras in their 3 piece set. You can of course get the Cobras in chrome, just like the one in the 4 piece set, for additional cost.
GearWrench 35pc micro driver set I have one of these and it comes in handy all the time. I'm a professional mechanic and this kit always comes with me on service calls.
or
Wera Tool-Check Plus Bit Ratchet Set with Sockets - Imperial Basically a fancier more indepth version of the GearWrench set. I don't own one, but its on my list and would likely replace the GW set at work. I'd bring the GW set home.
or
Knipex Alligator Plier Set What can be said, Knipex makes the best pliers. You can grab hex heads, turn pipe as it grips like a mother, and any other thing your sweet little heart desires.
or
If you want to save up a little more cash, these Knipex Plier Wrenches are awesome or so I've heard Also on my list of stuff to get. These play a similar role as adjustable wrenches.
I can't speak highly enough of knipex's slip joints and especially their pliers wrench. Holy hell do I love their pliers wrench. This Raptor is also exceptional, and all the Raptor branded hand tools are are a very good quality for a very fair price.
Makita, Milwaukee and Dewalt all make very serviceable cordless tools. My brother runs Makita and likes them a lot. I'm in DeWalt, and some of the new 60v stuff is really cool. Also Dewalt has this impact driver which has a push button bit release instead of a collet and a three speed torque selector. Probably my favorite tool of all time.
I own this set. Pretty much covers everything so need to do.
https://www.amazon.com/KNIPEX-Tools-00-20-US1/dp/B000X4KNTG
Snap on sells knipex pliers, dykes, etc. If you don't own any knipex stuff, it's great.
My person favorites are these:
https://www.amazon.com/7401250SBA-10-Inch-Leverage-Diagonal-Cutters/dp/B000X4MPAQ
https://www.amazon.com/KNIPEX-Tools-00-20-US1/dp/B000X4KNTG/ref=sr_1_5?s=hi&ie=UTF8&qid=1526243314&sr=1-5&keywords=knipex+plier+set
Snapon sells these with their logo on them, I've worn a few sets of the pliers out, the dykes I generally lose before I wear them out.... They are great for cutting through shift cables and doing drum brake work.
Actually I didn't buy a set, but you can get a better deal on them if you do get one.
First I bought the 7 inch after using a coworkers' and thought it was nifty, but still thought it was ridiculous spending $45 on a set of pliers. Then I realized how amazing they are and about a month later got the 12 inchers and had no problem paying the $60 for them. Honest to fuck, even if they were $200 today I would buy them again.
Anyway. The set I've seen has 7, 10, and 12 inchers, and I can't see myself using the 10. Maybe on the rare occasion I need it to fit somewhere ridiculous. So, my next purchase is actually going to be this set which has the CUTEST little 6" model that I want for fitting in small places. Then maybe some day the 16 inch but I really have no use for that at the moment. Maybe just to match my 1.5 inch ratcheting wrench which also gets used about twice a year.
I would get him a these, seriously the best I've ever used and totally worth the money. A few companies have copied the push button design, but there is no comparison. Traditional toungue and groove pliers are so clumsy after using knipex.
Knipex get pretty rave reviews from people on YouTube if you want to see why it's worth paying 2x there price of channel locks.
Knipex 002006S1 3-Piece Cobra Pliers Set (7-Inch, 10-Inch, & 12-Inch) https://www.amazon.com/dp/B000X4KNTG/ref=cm_sw_r_cp_apa_mG5mybQPZEYZ4
I'm using Amazon links as requested, but if you have a local big box tool stop you can get the store brand of most all these items for the same price or less. I know from personal experience, that from the tools I've listed all but two of the items are cheaper in store than on Amazon.
Everyone needs a knife! (~$7 home depot)
Razor blade
Where are you going to keep everything? (~$10 home depot)
Utility Sack
You'll need a good all around screw driver. (~$8 home depot)
6-in-1 Reversible Screwdriver
Need some basic general maintenance pliers? (~$20 home depot)
Pliers Set
Ratcheting screwdriver for those repetitive screw jobs. (~$20 sears)
Ratcheting Screwdriver
Where the hell did I put that T6?
Magnetic Precision Screwdriver Set
Where did that damn screw go?
Flashlight
Extra stuff!
I recommend the ball end ones specifically if you don't have a good angle on what your trying to get at (cough towel bar cough cough).
Long Arm Ball End Hex Key Wrench Set
For those damn pesky wires and that damn lack of a third hand.
Helping hands
When duck tape and gum wont cut it.
Beginners soldering iron kit
I have used all of these specific items extensively besides the ball end hex keys, and that specific helping hands.
https://www.amazon.com/Replacement-Handles-Klein-Tools-89/dp/B00093D7AI/
I keep this set right next to my 3d printer the flush cutters work great for cutting rafts and supports and the pliers work great for cleaning the nozzle gunk. i bought it at home depot but you can find them on amazon.
https://www.amazon.com/OTC-4502-Hose-Clamp-Pliers/dp/B000I1KJT8
If anyone in the UK wants the 3 important tools, then they're £7 on Amazon right now: https://www.amazon.co.uk/Draper-Redline-67924-Handles-3-Piece/dp/B011IL426C/ref=sr_1_3?s=diy&ie=UTF8&qid=1480297623&sr=1-3
Wish I didn't pay £18 at Hobbycraft now!!
So, I ordered one of these on a bit of a whim, and it arrived today. Turns out it's actually kind of badass. Seriously heavy construction. The only problem is the curve is kind of backwards to really make the blade comfortable to use, but that's a pretty small gripe.
Check this stuff out. You will use this stuff a lot.
I'd also recommend looking into Snap-on's extra long wrenches in the 7/32-1/4", 5/16-3/8", and 7/16-1/2" sizes.
You don't actually need 'chainmail' pliers. Some basic pliers from your local home center will be just fine. Like this set will be fine I think:
https://smile.amazon.com/Stanley-84-114-Piece-6-Inch-Diagonal/dp/B0006HVU4W/ref=sr_1_2?s=power-hand-tools&ie=UTF8&qid=1481595883&sr=1-2&keywords=pliers
Bonus crappy cutters as well!
Incredibley expensive, but the best damn one handed wrenches I've ever used: KNIPEX 00 20 06 US2 3-Piece 7, 10 and 12 Pliers Wrench Set https://www.amazon.com/dp/B005EXNT2Y/ref=cm_sw_r_cp_apa_FJOkybNPVQC6W
I actually don't own one and I most likely never will. I got a couple of Knipex Cobra pliers as well as a Knipex Pliers Wrench instead and it's way faster and more comfortable to work with.
They grip so tight you can literally put one on a pipe and stand on it. Every mechanic where I work use them and I´ve never seen a single one with chipping, bad teeth or which has been bent.
Because few people here will know what water pump pliers are, get these:
https://www.amazon.com/Knipex-002006S1-3-Piece-10-Inch-12-Inch/dp/B000X4KNTG
Saving up for this set
https://www.amazon.com/dp/B005EXNT2Y/ref=cm_sw_r_udp_awd_lEe8tb1V3C6BJ
I'm using two tools from a set like this one. I have pretty small fingers, so that makes it easier.
You can try these
Their "entire line"?
https://www.amazon.com/Craftsman-933153-Electrical-Pliers-Set/dp/B00K5Q87YK
Well, 100 ft of wire runs about $8, a simple plier set runs $9,and then all you have left is to find something to use as a base.
All you need is $16 and some time. And maybe practice.
A lot of it depends on your preferences; I like thick, cushion grips, for example, while many people like thin, dipped handles.
If you don't need normal slip-joint pliers, I would go with NWS, Gedore, Wiha, Knipex, etc. They don't make slip-joints, though, so I don't use them; they are also expensive.
I have a bunch of Channellock brand pliers; I wouldn't buy them again. There is a Gearwrench set on my Amazon wish list:
https://www.amazon.com/dp/B0014ZXY80
But they make an almost identical version with dipped grips.
Depends, I just yesterday bought a set of 3 channel lock tongue and groove pliers on sale for under $50CAD new (https://www.amazon.com/Channellock-GS-3A-Tongue-Groove-Acetate/dp/B01HZHASN4)
And looked online at the equivalent of it for knipex and its 3 times the price (https://www.amazon.ca/Knipex-002006S1-3-Piece-10-Inch-12-Inch/dp/B000X4KNTG/ref=mp_s_a_1_3?keywords=knipex+cobra&qid=1570395546&sr=8-3)
I will probably still pick up the knipex ones later because they work great. But the big factor here is price difference
A while back, Amazon had a flash deal on this set for $57 which was too good to pass up, but I'm not sure I'd grab it at the current price.
For AN fittings, a flare nut wrench is the most acceptable way to go and I see you have a couple of those. If those don't fit, open end wrenches, crows feet, or the Knipex pliers-wrench (expensive but so worth it) are fine. The problem with the crescent/ford is they can loosen up and will round off fittings whereas the Knipex can apply pressure onto the nut.
I know klein sells replacement handles:
8/9" handles https://www.amazon.ca/89-Replacement-Tools-Koat-Tenite-Handles/dp/B00093D7AI
20 bucks canadian
7"http://www.kleintools.com/catalog/plier-handles/replacement-handles-7-pliers
They are decent handles, i've seen some guys at work use them.
ideal also sells replacement handles :
https://www.idealind.com/ideal-electrical/us/en/products/electrical-tools/10-hand-tools/1-pliers/tenite-grips.aspx
epoxy them on and they won't be coming off.
There are double jointed long handled pliers, like this:
https://www.amazon.com/Crescent-PSX200C-Long-Reach-Pliers/dp/B0091KHK6C/
https://www.amazon.com/GearWrench-82005-Double-Pliers-Straight/dp/B000NIAK1S/
I've found their "plier wrench" does a much better job than a regular adjustable wrench and can replace the open ended wrench in many cases, though I'm not sure how much you use your box end.
https://www.amazon.com/KNIPEX-Tools-00-20-US2/dp/B005EXNT2Y
that's the set I have.
Well, I think I can shed a little light on what you're in for.
Years ago, a good friend of mine was still living at home with his father. We were both around 20 years old and my friend had just met his future wife. Finding time to be intimate in his father's small house was difficult at best.
One fortunate afternoon, his dad was out and about... my friend took full advantage, purchasing a 3-pack of Trojans and a rose to woo his beautiful lady. Sexy times ensue...
Afterwards, my friend tossed the condom in the bathroom trash (a notoriously short, easily accessible trash barrel). He then left to take his lady for a bout of laser tag or whatever us kids did at the time for amusement.
Cut to later that day, my friend returns home to find his dad crouched behind the family dog on the kitchen floor. Armed only with a pair of pliers and limited veterinary skills, he was pulling the used condom from the dog's rear end. The condom stretched about a foot before snapping free in a miasmic haze of Alpo and regret.
His father turned to my friend with a look of utter disappointment on his face and said, "I have no idea what you're up to when I'm not around but this will never happen again."
We all know the dog ate the condom... but on those nights when he's alone in bed, dark and cold, he wonders what his dad thinks.
TL;DR buy yourself a set of these: http://www.amazon.com/Stanley-84-114-Piece-6-Inch-Diagonal/dp/B0006HVU4W/ref=sr_1_1?ie=UTF8&qid=1335527522&sr=8-1
knipex (one of the really good tool/plier brands), 66€ on Amazon germany https://www.amazon.de/Knipex-87-560-Cobra-XXL-Wasserpumpenzange/dp/B000SOVRNC
It's the 89 replacement handles. Just put a set on yesterday, love them so far!
https://www.amazon.com/Klein-Tools-89-Replacement-Tools-Koat/dp/B00093D7AI
This is what OP bought
If you want to get fancy, you can get these
These are a nice uninsulated set of knipex, they're cheaper than the insulated version but you can spend the bit more if you want, probably wouldn't get a shock off domestic voltage with either ones anyway https://www.amazon.de/Knipex-00-20-11-Montage-Paket/dp/B001094GLY/ref=mp_s_a_1_7?keywords=knipex&qid=1568584697&sr=8-7
KNIPEX Tools 00 20 06 US1, Cobra Pliers 7, 10, and 12-Inch Set, 3-Piece
https://www.amazon.com/dp/B000X4KNTG/ref=cm_sw_r_cp_apa_aRnXBbWFRBW74
These are phenomenal as much as I've used them so far
my favorite oil filter wrench is decent grip sandpaper. currently using a strip of 150 grit for drywall sanding. grips oil filters like a mofo.
edit: you mentioned amazon. I've bought some Tekton branded items off of there and it feels in line with harbor freight, maybe up in their pro line as to quality. however if I ever had a issue they hooked me up even years later. I bought a hose reel from them 3 years ago and the locking arm started to wear out. they shipped me a new part for it free of cost. even gave me a maintenance pointer on it. gear wrench is on there and they got good enough tools (never dealt with something broken) I'm eyeballing these Knipex non nut fuckers right now https://www.amazon.com/KNIPEX-00-20-06-US2/dp/B005EXNT2Y/ref=sr_1_8?s=power-hand-tools&ie=UTF8&qid=1496376559&sr=1-8&keywords=knipex
Corollas are great cars! I thought about getting one as my second car.
Yeah, you do need tools for most things. If you are able, you can assemble a small tool kit for under $100, and that will allow you to do a lot of stuff. Changing your own oil is a very good place to start, and most cars only need a single socket to do it.
If you want to get into car maintenance without tools, you can clean your car out, check and top off the fluids accordingly, or go to a gas station that has an air pump to pump up your tires.
Here is a good beginning to a tool kit:
Screwdrivers
Sockets
Pliers
Wrenches
What type of budget does your team have?
How much space is available as your work area?
How experienced at building robots are the mentors?
What build system does you team intend to use? How many custom parts do y'all want to make?
What level of CAD skills does the team have?
We need to know these things to give valid advice. If your team has $100 to spend on tools the list is really different than if your team has $500. If your team has ~$4000 and really experienced mentors the list is also totally different.
​
Let's assume your team has really limited budget and wants to make the most of it. I will also assume you are using the REV system.
Here is my minimum tool list:
5.5 mm Nut Driver - http://www.revrobotics.com/rev-41-1119/
5.5 mm wrench - http://www.revrobotics.com/rev-41-1374/
Allen wrench set - https://smile.amazon.com/AmazonBasics-Hex-Allen-Wrench-Ball/dp/B0776C2D6H/
Rotary Cutter - https://smile.amazon.com/WEN-2305-Rotary-Tool-Shaft/dp/B003BYRFH8
Hand drill - https://smile.amazon.com/BLACK-DECKER-DR260C-Drill-Driver/dp/B00T2VJ93C/
Hack saw - https://smile.amazon.com/Tactix-267031-Adjustable-Hacksaw-Frame/dp/B00ABBUU2Q/
Bench Vice - https://smile.amazon.com/WEN-453BV-3-Inch-Heavy-Swivel/dp/B07KKXQQ3S
Metric Drill bit set - https://smile.amazon.com/Drill-Warehouse-99pcs-1-5mm-Titanium/dp/B01NC25BRK
Pliers set - https://smile.amazon.com/AmazonBasics-Tools-4-Piece-Pliers-Set/dp/B015X2NHOK
That works out to be ~$110 + shipping and tax. These are the bare minimum tools IMO. If you can answer the questions above I can give you some better advice.
- Frank
The oven pan, the frying pan, etc. Mittens breack. The tail of the frying pan melted.
The idea of grabbing anything hot, and securely move it from one place to the next. Key word is secure.
For example I love to cook potatoes on a metal plate. I cut them into round wheels nd place them on the heated steel plate. Let them cook then serve hot or cold with onions and sunflower oil.
Use knife to turn them bad boys while holding the plate with the other hand, using pliers.
Sorry, english is not my native tongue
This things https://www.amazon.com/Stanley-84-114-Piece-6-Inch-Diagonal/dp/B0006HVU4W/ref=sr_1_4?s=power-hand-tools&ie=UTF8&qid=1541369010&sr=1-4&keywords=pliers.
Steel plate: https://www.amazon.com/Hot-Rolled-Steel-Plate-10/dp/B00YWBQ5AW/ref=sr_1_3?ie=UTF8&qid=1541369144&sr=8-3&keywords=steel+plate
I cut out mine from a big sheet of steel using a grinder. Not sure about thickness tho.
Honestly, I learned the importance of pliers in the kitchen back in highschool and my burned fingers/ year dropped to 0. But, to each his oun.
Crescent PSX200C X2 Long Reach Pliers https://www.amazon.com/dp/B0091KHK6C/ref=cm_sw_r_cp_api_c1W.Bb3NHS178
Use a pliers like this that can go in the hole deeper most autozones or advanced auto might carry ones like this
Right at Home Depot you can get these:http://www.homedepot.com/p/Channellock-Griplock-12-5-in-and-9-5-in-Tongue-and-Groove-Pliers-Gift-Set-GLS-1/100029000 For a couple dollars more you're getting Channellocks, plus, as you can see these are bigger being (9.5 and 12.5 inches. Please be aware that with this style of pliers the teeth are very aggesive and really chew on the work piece. Great grip, especially on pipes etc., but not great for stuff you don't want marred. For a little more $ you can get classic channellocks with the v-jaw or the straight jaw. These are workhorse tools which will withstand years and years of use and abuse. NOTICE GUYS: While looking for the two piece set of v-jaws for r/incrediby729 I came upon this really good Amazon price for a two piece Channellock 9-1/2" lineman's and 10" tounge and groove for $26.99! If I didn't just buy this pair of lineman's I'd buy this in a heartbeat. http://smile.amazon.com/Channellock-GS-10-2-Piece-Plier-Set/dp/B004WQZW9W/ref=sr_1_12?ie=UTF8&qid=1458174670&sr=8-12&keywords=channellock+2+piece+set
Knipex 22" Cobra Pliers - Amazon
I've had these a year now. Once thought of as a novelty has turned into a shop necessity.
You need a set of hose clamp plyers. Something like this...
https://www.amazon.com/OTC-4502-Hose-Clamp-Pliers/dp/B000I1KJT8/ref=pd_bxgy_263_img_3?_encoding=UTF8&pd_rd_i=B000I1KJT8&pd_rd_r=DSGQ7584HD7GZ57ZJV8X&pd_rd_w=TwJv5&pd_rd_wg=8ydHF&psc=1&refRID=DSGQ7584HD7GZ57ZJV8X
Different brand cars/bikes use different style of clamps. Someone please chime in if they know exactly the style OP needs...
What type of bike?
Someone better tell them that, then.
https://www.amazon.com/Knipex-002006S1-3-Piece-10-Inch-12-Inch/dp/B000X4KNTG/ref=sr_1_2?ie=UTF8&qid=1521552216&sr=8-2&keywords=knipex+slip+joint+pliers