Best set screws according to redditors
We found 26 Reddit comments discussing the best set screws. We ranked the 17 resulting products by number of redditors who mentioned them. Here are the top 20.
We found 26 Reddit comments discussing the best set screws. We ranked the 17 resulting products by number of redditors who mentioned them. Here are the top 20.
Gut the lock entirely then put the lock into a vise and drill the caps all the way through with a drill bit that is smaller than the caps.
After that you can use a punch with a hammer and knock the caps out. The hole allows some relief for the cap to slide down the chamber without doing a lot of damage on the way down. I would suggest that you drill and punch every other one to start.
Start off with a M3.5 tap and run it all the way through to make it a serrated chamber. To replace the caps, use a M4 tap to widen the diameter a bit and replace the caps with M4x4mm grub screws.
This was how I did it.
$0.13: [A Socket Set Screw] (http://www.amazon.com/Holo-Krome-32114-Socket-Screw-Uncut/dp/B0037QFO4G/ref=sr_1_3/179-8080515-3877040?s=industrial&ie=UTF8&qid=1458494889&sr=1-3&refinements=p_4%3ASmall+Parts)
I believe the nut is a square m3 nut.
https://www.amazon.com/Square-Stainless-Steel-Pieces-pitch/dp/B01D1B79US
or
https://www.amazon.com/100pcs-Stainless-Steel-Square-Nuts/dp/B018JPZNS6
The screw is an m3 grub screw, 6mm or 8mm long. Not sure. I would recommend you measure your existing one.
https://www.amazon.com/uxcell-300pcs-Stainless-M3x6mm-Socket/dp/B01ARSGVY8
or maybe get an assortment
https://www.amazon.com/Raogoodcx-250pcs-Socket-Assortment-Plastic/dp/B01G30ZN3E
M2.5 Flat Point Set Screws Hex Socket Grub Screws /Stainless Steel 304/Pack of 50-Piece Size M2.5 x 4 mm
https://www.amazon.com/gp/product/B01D891PS0/ref=oh_aui_detailpage_o02_s00?ie=UTF8&psc=1
Work great in my Serpent mini
M2.5 Flat Point Set Screws Hexu Socket Grub Screws /Stainless Steel 304/Pack of 50-Piece Size M2.5 x 4 mm
https://www.amazon.com/gp/product/B01D891PS0/ref=oh_aui_detailpage_o02_s00?ie=UTF8&psc=1
Prime-Line 9182625 Socket Set Screws, #8-32 X 1/4 in, Grade 18-8 Stainless Steel, 25-Pack https://www.amazon.com/dp/B07DS7FQYY/ref=cm_sw_r_cp_apa_i_TQGyCbYNTCY7T
This should be what you're looking for. As far as I know, all saber manufacturers use 8-32 screws.
Ahh yeah sometimes you just have to swap the screws on some buttons to make them more compatible. It’s a pain for others but I personally like having the flexibility to adjust. Here’s the assorted set screes I have
I recently got this set. I’m finding most makers use the largest size (M3), but don’t use the longest length (6mm). I often find that after adding desired spacers the installed grub screws are not long enough to reach. Switching the 4 or 5 mm originals for 6 mm work great.
https://www.amazon.com/dp/B073H68PJH?
I checked my box too. I got spare philips instead of hex. But I found a link on Amazon that were the same specs and preferred by a lot of vapers.
Amazon Link
I believe these will fit fine
http://www.amazon.com/gp/product/B000FMUFO4/ref=oh_aui_detailpage_o00_s00?ie=UTF8&psc=1
While I'm not sure which height you would want, something like these brass standoffs are what you want. That being said, you would likely have to get some sort of headless screw (these are just an example, not sure which kind would be best or fit) to screw into the case and then use tiny m2 screws to hold the plate on.
If you use an inconel screw for the gas restriction, then a set screw and that would be using the same high end parts on ar-15 adjustable gas blocks on the market right now.
If you can use a spare gas block to know where to drill into your current gas block, I don't see why you can't get this to work on the cheap.
M2.5 x 4 mm
https://www.amazon.com/gp/product/B01D891PS0/ref=oh_aui_detailpage_o02_s00?ie=UTF8&psc=1
according to here
As far as I know, Tyler uses standard M4 threads on his pedals, which seem to be the most used in the industry.
Perhaps set screws and and some threadlock will do?
https://www.amazon.com/M4-0-70-Socket-Screws-Stainless-Quantity/dp/B01JAL9Y6A
https://www.amazon.com/Loctite-504466-Strength-Threadlocker-19-gram/dp/B0053ZNLTO/
Contacted them this morning, thanks for the info friend.
EDIT: What is the size of them according to this Amazon page?
https://www.amazon.com/gp/product/B014OMFU1I/ref=oh_aui_detailpage_o06_s00?ie=UTF8&psc=1
When I lost one I just bought this.
Of course that means I'll never lose another one, or it will be SAE. :)
HVAZI M2 M2.5 M3 Stainless Steel Internal Hex Drive Cup Point Set Screws Assortment Kit
https://www.amazon.com/HVAZI-Stainless-Internal-Screws-Assortment/dp/B073H68PJH/ref=sr_1_7?ie=UTF8&qid=1540570606&sr=8-7&keywords=metric+set+screw+assortment&dpID=41zlqbR9frL&preST=_SX300_QL70_&dpSrc=srch
Set Screw Set
I much prefer metric set/grub screws...the trick is don’t crank’em down...IMHO. you don’t get any better connection by over-torquing.
M5-0.8 hand tap, and corresponding set screw
https://www.amazon.com/Hillman-Group-1607-M5-0-80-10-Pack/dp/B00HYKCJFS/ref=sr_1_3?qid=1568507934&refinements=p_n_feature_fourteen_browse-bin%3A11434060011&s=industrial&sr=1-3
https://www.amazon.com/0-8-Metric-Taper-Plug-Taps/dp/B00870161M
It looks like this is the right one; Cyful 60pcs M3x 3mm Alloy Steel Cone Point Hex Socket Set Grub Screw Headless Black (M3x3) https://www.amazon.com/dp/B07JYF2GNZ/ref=cm_sw_r_cp_api_i_sxGYDb41MZYH9