Reddit Reddit reviews Black Plastic Drag Chain Cable Carrier 10 x 15mm for CNC Router Mill

We found 8 Reddit comments about Black Plastic Drag Chain Cable Carrier 10 x 15mm for CNC Router Mill. Here are the top ones, ranked by their Reddit score.

Industrial & Scientific
Industrial Hardware
Hardware Chains
Black Plastic Drag Chain Cable Carrier 10 x 15mm for CNC Router Mill
Check price on Amazon

8 Reddit comments about Black Plastic Drag Chain Cable Carrier 10 x 15mm for CNC Router Mill:

u/smittyjones · 5 pointsr/DIY

What about like a snake wiring track?

I'm thinking like this. That's what Caravans use at the bottom of their sliding doors and they (usually) work for years and years and thousands of opens and closes.

This chick made a power drawer in her Harbor Freight toolbox, she used the snake wiring like I was talking about. You can see a glimpse of it in image 66, but sadly, she doesn't really talk about the wiring much.

u/zombieregime · 2 pointsr/homeautomation

yeah. to rotate the blinds youd have to figure out how to drive the center rod in the track(stepper with some sort of interface gear). Or, possibly set it up on a coil cord with a cable running through it, or a cable chain.

To retract the curtains youll have to run your own pullys and cables.

Might be worth it to just replace them with a unit that can be modified(chain and rope on the side). If youre renting, just ask the manager to have maintenance take the existing one down(or take it down yourself and stuff it in a closet).

u/dangerousbrian · 2 pointsr/shapeoko
  1. Deffo the wires could be loose, check them and make sure they are really solid, with good crimps, heatwrap and anything else that will reinforce them. If you can get some cable wrap and drag chain. I have had plenty of jobs ruined because a cable got pinched in the gantry and skipped steps.

  2. Generally if the firmware is screwed then you won't get any movement at all, so I doubt that is an issue.

  3. Does the motor work if plugged into another driver? again as the motors are pretty much two coils of wire you have to drive a lot of current down them to break them. They will get very hot and generally not work at all.


    When you say moving "in broken halting steps" that does suggest to me that the motor is working but does not have enough torque to turn. That could be that the wheels are too tight on the makerslide or that the motor is not getting enough current, but only look into that after you are sure the wiring is Aok.

u/[deleted] · 2 pointsr/CNC

Amico

http://www.amazon.com/Amico-Black-Plastic-Carrier-Router/dp/B00880AVL2/ref=sr_1_5?ie=UTF8&qid=1394316583&sr=8-5&keywords=cable+chain

P.S. I'm stealing your username for an /r/bandnames submission.

u/Rocket2Uranus · 1 pointr/PrintrBot

I have a Printrbot Simple Metal, and I replaced its crappier cable sleeve with a cable chain like all other high-end 3D printers:
http://www.amazon.com/Black-Plastic-Chain-Carrier-Router/dp/B00880AVL2. The Play's sleeve is really nice quality, and all you have to do is route a stiff wire from under the base and up through the sleeve.

u/BiggRanger · 1 pointr/homelab

Insanity is not using cable-chain so you can slide those servers in and out without unplugging everything every time.
https://www.amazon.com/Black-Plastic-Chain-Carrier-Router/dp/B00880AVL2

u/ChiefKnightOwl · 1 pointr/FTC

Our team uses a cable carrier for the prismatic part of the arm. It is very clean:

https://www.amazon.com/Black-Plastic-Chain-Carrier-Router/dp/B00880AVL2

​

u/n3farious · 1 pointr/CableManagement

In addition to this, consider a cable guide (typically used in CNC type equipment) for your power and network cables that go to the wall.. https://www.amazon.com/Black-Plastic-Chain-Carrier-Router/dp/B00880AVL2?ie=UTF8&*Version*=1&*entries*=0