Reddit reviews TEKTON Long Arm Ball End Hex Key Wrench Set, 26-Piece (3/64-3/8 in, 1.27-10 mm) | 25282
We found 12 Reddit comments about TEKTON Long Arm Ball End Hex Key Wrench Set, 26-Piece (3/64-3/8 in, 1.27-10 mm) | 25282. Here are the top ones, ranked by their Reddit score.
Ball ends allow up to a 25-degree entry angle to reach around obstructionsChamfered, straight ends offer a snug fit and insert smoothly into fastener head, reducing wearBlack oxide finish protects against corrosion without added plating that could chip off under high-stress contactLong arm/short arm design offers extended reach on one end and extra leverage on the otherColor-coded housing for instant identification of size Series
This might be excessive, but I wanted to be thorough so you can see what all is out there. I am having trouble thinking of anything that the following tools can't do, in terms of AR building and maintenance. This is basically my setup at home, though some.of the brands and whatnot are different.
I am operating under the assumption that you already have some basic hand tools in addition to the torque wrench.
The only things you absolutely need are roll pin punches and an armorer's wrench and some basic hand tools like Allen wrenches, screwdrivers, needlenose pliers and so on. The rest just expedite the process and help solve weird issues that may come up.
Wheeler Engineering Roll Pin Starter Punch Set https://www.amazon.com/dp/B01B3NWBVI/ref=cm_sw_r_cp_apa_QJZDAb1ZFBQ80
Wheeler Roll Pin Punch Set https://www.amazon.com/dp/B00EE6GHVW/ref=cm_sw_r_cp_apa_4JZDAbV5YGA8M
Wheeler Hammer and Punch Set In Plastic Case https://www.amazon.com/dp/B004SY07HU/ref=cm_sw_r_cp_apa_FNZDAb1Y74EF0
Geissele Automatics 10-169 AR15/M4 Reaction Rod https://www.amazon.com/dp/B01EY6WFAI/ref=cm_sw_r_cp_apa_hOZDAbD3JHBAE
Aeroshell 33ms / MIL-G-21164D / MIL-SPEC Barrel Nut Thread Grease + 1/2oz can https://www.amazon.com/dp/B01BJ3HE0K/ref=cm_sw_r_cp_apa_4OZDAbQGRYJJ2
TEKTON Long Arm Ball End Hex Key Wrench Set, Inch/Metric, 26-Piece | 25282 https://www.amazon.com/dp/B00I5THF4W/ref=cm_sw_r_cp_apa_PPZDAbQ05H680
TEKTON Long Arm Star Key Wrench Set, T10-T50, 9-Piece | 25291 https://www.amazon.com/dp/B00I5THF9M/ref=cm_sw_r_cp_apa_cQZDAbRX59VNW
IRWIN Tools Multi-Purpose Bench Vise, 5-Inch (4935505) https://www.amazon.com/dp/B009TOCZEC/ref=cm_sw_r_cp_apa_1QZDAbT8R47J0
Yost UP-360 Universal 6 Inch Prism Style Jaw Cover https://www.amazon.com/dp/B01EVQH42U/ref=cm_sw_r_cp_apa_aRZDAbRHAV73E
Real Avid Gun Tool Pro - for Modern Sporting Rifles https://www.amazon.com/dp/B00IMHX5KA/ref=cm_sw_r_cp_apa_bUZDAbEB87JFB
Wheeler Firearms Accurizing Torque Wrench https://www.amazon.com/dp/B0012AXR4S/ref=cm_sw_r_cp_apa_xWZDAb1SRYD6D
Wheeler Professional Gunsmithing Screwdriver Set (43-Piece) https://www.amazon.com/dp/B00HTN4EWG/ref=cm_sw_r_cp_apa_HXZDAbQX5BEWF
TacWater USA AR15/M4/M16 Tools Multi-Purpose Tool Set (W) https://www.amazon.com/dp/B079H5WWZ3/ref=cm_sw_r_cp_apa_GYZDAbRGY3CNH
Takedown Pivot PIN Tool set 223 556 6.8 SPC 300 AAC https://www.amazon.com/dp/B017OUSJFQ/ref=cm_sw_r_cp_apa_V.ZDAbSHZPEG5
Magpul Bev Block https://www.midwayusa.com/product/1015877615/magpul-bev-block-ar-15-action-block
I got a few craftsman tools recently and while I bet they are overall "fine" I've been pretty disappointed with a few of them. I would also look to gearwrench, a bit higher quality and the price isn't much worse.
I'd buy this (1/4 and 3/8th sets) - $109
http://www.coastaltoolsupply.com/product/KDT-80550F.html
Half inch impacts and ratchet - $130
http://www.coastaltoolsupply.com/product/KDT-84949N.html
https://www.amazon.com/dp/B00BTEXPNU/ref=twister_B0154R8KHI?_encoding=UTF8&psc=1
Wrenches, long pattern full polish and a free knife. - $118
http://www.coastaltoolsupply.com/product/KDT-81900KF.html
Ratcheting wrenches - $50
http://www.sears.com/gearwrench-20pc-combination-ratcheting-wrench-set-sae-mm/p-00935720000P?plpSellerId=Sears&prdNo=20&blockNo=20&blockType=G20
Screwdrivers - $28
http://www.sears.com/craftsman-17-pc-screwdriver-set/p-00931794000P?plpSellerId=Sears&prdNo=2&blockNo=2&blockType=G2
Hex keys - 18 dollars
https://www.amazon.com/TEKTON-Wrench-Metric-26-Piece-25282/dp/B00I5THF4W/ref=sr_1_3?s=hi&ie=UTF8&qid=1502574535&sr=1-3&keywords=hex+keys
Half inch extensions - 25 dollars
https://www.amazon.com/GearWrench-81300-Piece-2-Inch-Extension/dp/B000NI93M0/ref=pd_bxgy_469_img_3?_encoding=UTF8&pd_rd_i=B000NI93M0&pd_rd_r=XREV1D7B7335G71T6D92&pd_rd_w=JLtGU&pd_rd_wg=3k6AP&psc=1&refRID=XREV1D7B7335G71T6D92
Total of 475 dollars, most of that ships free if you have prime, the rest from coastal tool supply ships for 8.95 flat rate or something. You could buy nut drivers or hex headed sockets with the rest of the money. Should be similar amount of useful tools, but much better ratchets. You could cut down the screwdriver set if you wanted and add stubby wrenches or something else. Again, that craftsman set would probably be fine, but I hate those ratchets and don't have any need for ignition wrenches and that extra stuff.
I agree, build you own kit. Below is my take. Know that some of those tools are not for every day use in networking, but who can resist getting more tools? Also, if you get all of these I realize it will be over $200. So, just use this list as a guide not a definitive list.
BAGS
ETHERNET TOOLS
SCREWDRIVERS
PLIERS and WRENCHES
POWER
MISC
SUPPLIES
As some of the other posters indicated, you will need a hex key. This is the standard screw on most bathroom accessory installations, e.g., towel racks, faucet handles, toilet paper roll holders, etc.
You don't need to worry about digging around to find the original hex key as a standard hex key will fit - you just need the right size.
Here's a link to a set on Amazon: Hex Key Set
You can also find these sets at the usual suspects, e.g., Ace, Home Depot, etc.
Now, for about $100 you'll never be stuck again. I'm amazed when I see people who aren't prepared for this kind of scenario.
I'm using Amazon links as requested, but if you have a local big box tool stop you can get the store brand of most all these items for the same price or less. I know from personal experience, that from the tools I've listed all but two of the items are cheaper in store than on Amazon.
Everyone needs a knife! (~$7 home depot)
Razor blade
Where are you going to keep everything? (~$10 home depot)
Utility Sack
You'll need a good all around screw driver. (~$8 home depot)
6-in-1 Reversible Screwdriver
Need some basic general maintenance pliers? (~$20 home depot)
Pliers Set
Ratcheting screwdriver for those repetitive screw jobs. (~$20 sears)
Ratcheting Screwdriver
Where the hell did I put that T6?
Magnetic Precision Screwdriver Set
Where did that damn screw go?
Flashlight
Extra stuff!
I recommend the ball end ones specifically if you don't have a good angle on what your trying to get at (cough towel bar cough cough).
Long Arm Ball End Hex Key Wrench Set
For those damn pesky wires and that damn lack of a third hand.
Helping hands
When duck tape and gum wont cut it.
Beginners soldering iron kit
I have used all of these specific items extensively besides the ball end hex keys, and that specific helping hands.
It depends on the caliber. You don't need an adjustable gas block with 300 blk, but it can help a lot with 5.56. With 5.56, you will generally want an adjustable gas block to limit the gas, an adjustable bolt carrier to vent the gas or, at the very least, an H2 buffer to slow down the bolt carrier.
The adjustable gas block is the most elegant solution, but an adjustable bolt carrier works well and is easier to install for most people. A heavier buffer will help it cycle reliably, but it will still be overgassed.
If you already have an adjustable gas block installed and your handguard holes don't align well with the adjustment screw, you might be able to get to it using ball end hex keys, like these Tekton ones. These will allow you some leeway in terms of the angle you need to get to it. If the area is just completely blocked off, you will have to take off the handguard.
Here's a list of basics that I bought recently to give you an idea:
Feeler Gauges
Hex Key Wrench Set
String Action Gauge
String Winder
Contact Cleaner for Electronics
Neck Rest
I already have various sized screw drivers, but if I didn't that would be on the list as well.
The above would be enough to do a basic setup: adjust truss rod, adjust action, get into the guts and clean the electronics. Everything will fit in a beat up old shoe box haha.
Along with YouTube videos, this book is a good reference guide. It has everything from basic repair and maintenance information all the way to repairing a broken neck or trying to repair a messed up truss rod.
As far as he's wrenches, I'd recommend ball ends like theseTEKTON Long Arm Ball End Hex Key Wrench Set, Inch/Metric, 26-Piece | 25282 https://www.amazon.com/dp/B00I5THF4W/ref=cm_sw_r_cp_apa_89DRAbKQ3YGR7
A ball head hex key is the right tool. It allows you to turn allen screws at an angle.
Here
I have a gunsmith set from amazon that has more than you need but has a bunch of useful bits like the punches.
any hex set would do you fine from amazon https://www.amazon.com/TEKTON-Wrench-Metric-26-Piece-25282/dp/B00I5THF4W/ref=sr_1_6?keywords=hex+set&qid=1557022314&s=gateway&sr=8-6
What kind of experience are you guys coming into this with?
Do you have mentors/are you yourselves familiar with the use and safety precautions necessary around power tools?
What kind of space are you in? Do you have a dedicated space to use or do you need to move things in and out of an area every meeting?
How much do you want to learn? Are you planning on using primarily Matrix/Tetrix this season or do you want to do custom fabrication?
If you're planning on using chain, I'd recommend getting at least one of these (Dark Soul #25 chain tool). You won't need to use master links again, and they're just in general great to have around.
I would definitely recommend getting Anderson Powerpole tools and items. Definitely get a TriCrimp and associated wire, connectors, and contacts, if you don't have them already.
I'd also recommend a few tools that come in useful just in general when it comes to FTC-- a good adjustable wrench is good to have around, whether you're doing custom or not. A ratcheting screwdriver is also good to have around, in addition to more standard versions. I'd also recommend my personal favorite allen wrenches (you can get just metric or standard sets, but I linked the paired version). For taking care of stuck bolts or anything else stuck, a good pair of locking pliers are also great. Also getting some good pliers for all your electrical needs is a good idea. Also extremely useful is a good square. On a similar note, a level is good for checking whether you actually bolted that part on straight.
You should also get a general set of combo wrenches and some of the specific sizes most common for FTC. Pretty much any reputable brand is fine for this-- don't spend more than about $50 for a set and $10 for an individual wrench (honestly, that would be super high, you should probably target half of that). A decent ratchet set is also good, but not absolutely essential.
Other good things to have around are a heat gun or heat bar (for doing custom plastic parts for your robot). You can do some great stuff with some creativity and some sheet polycarbonate.
To go with that, a vinyl cutter is great for doing sponsor decals and general cool stuff.
As far as "essentials" go, that depends on where you want to go. If you want to do lots of custom work-- or use something like 80/20, then you'll want some other tools to do that work. A good power drill is absolutely essential, and if you have the space, I'd definitely recommend getting a solid miter saw and an aluminum cutting blade (I know some people consider them too dangerous, but with proper safety training and precautions, I've never had a student or mentor get injured with one).
As far as materials for doing custom work go, I'd recommend getting some box aluminum (1x1 and 1x2) tubing, 1/8" and 1/16" polycarbonate (I'm partial to the dark tinted stuff, but it's a bit more expensive), and a full assortment of #6 and maybe #8 hardware. You'll also want some M3 screws for face mounting AndyMark and REV robotics motors. I like to use Copper State for this, because while they have a totally garbage web ordering system, their prices are great, and their website isn't that bad (to be honest, I'm a bit spoiled by McMaster-Carr).
You probably don't need me to tell you what kind of COTS parts might be good (if that's within the scope of this money). Electronics, good phones (not those stupid ZTEs), motors, are all good.
You'll notice that I'm not suggesting the very budget stuff-- while you can go that direction if you need to, quality tools help you get quality results. If you have the money to get and use the right tools for the job, I always recommend doing that as opposed to cheaping out with something you'll just end up breaking and messing up your robot with later.
A decent chunk of the tools I linked are suggested by my personal favorite review site, The WireCutter/SweetHome. I've used the majority of them, and my experience has been good enough that I don't have an issue recommending their suggestions for other tools relevant to FTC.
Hopefully that was somewhat helpful. I'd definitely consider the answers to the questions at the top-- they can help you narrow down what will actually be useful for you. I can definitely give more specific suggestions if you know what direction you're taking with robot building techniques and how much space you have/ whether you have to move.