(Part 3) Best automotive light bulbs according to redditors
We found 1,326 Reddit comments discussing the best automotive light bulbs. We ranked the 645 resulting products by number of redditors who mentioned them. Here are the products ranked 41-60. You can also go back to the previous section.
I did a k-suspension harness, hella h4 bulbs and rampage housings. love how much light they put out without looking obnoxiously bright like LED lights. At the very least you should do the harness. Makes a world of a difference.
Holy shit, guys. You just buried /u/sainisaab because you have no idea what the fuck you're all on about.
There are HIDs made specifically for reflector housings. They are designated with an "R" in the bulb number. "S" is for projectors. If you actually look at one, like this D2R, you'll see part of the bulb is masked off to reduce output. Here's a D2S (the projector bulb) to compare.
Some car makers include these bulbs stock, from the factory. They are not the blue ones you see retrofitted all the time.
So it is actually a 3 part ordeal.
The actual fog lights since my car didn't come with them, and the stalk. Then I did some c-shaped drl since I have leds in my high beams and the factory drl doesn't work with leds, but then the c-shaped drl didn't work for a little bit so I bought the drl turn signals, and then the previous c-shaped ones started working again. I will just post all of my mods below:
Fog lamps with brackets : https://www.amazon.com/dp/B01FL8DPWU?ref=ppx_pop_mob_ap_share
Light stalk : https://www.amazon.com/dp/B00AWO7XOK?ref=ppx_pop_mob_ap_share
C-shaped DRL : https://www.amazon.com/dp/B014P7LPEI?ref=ppx_pop_mob_ap_share
Sequential LED Turn signals with DRL : https://s.click.aliexpress.com/e/5veD22k
9005 LED High Beam : https://www.amazon.com/dp/B075J9S4DT?ref=ppx_pop_mob_ap_share
H11 55W HID Low Beam : https://www.amazon.com/dp/B07CMKT2F4?ref=ppx_pop_mob_ap_share
7440 7443 LED Brake/Tail Light : https://www.amazon.com/dp/B07GTKLF32?ref=ppx_pop_mob_ap_share
7440 LED Turn Signal (rear) : https://www.amazon.com/dp/B07Q8RZRZV?ref=ppx_pop_mob_ap_share
194 LED License plate/used as side markers in the front/a couple other places : https://www.amazon.com/dp/B07BT23WVC?ref=ppx_pop_mob_ap_share
194 LED side marker bulbs (not used but the correct ones if you want yellow, I liked the white and it was what I had when the originals burnt out but didn't ever change them from the above link) : https://www.amazon.com/dp/B01KY7GCXW?ref=ppx_pop_mob_ap_share
License plate smoke : https://www.amazon.com/dp/B007LICQ9M?ref=ppx_pop_mob_ap_share
Grille : https://rover.ebay.com/rover/0/0/0?mpre=https%3A%2F%2Fwww.ebay.com%2Fulk%2Fitm%2F254096211721
K&N 33-2480 Air Filter : https://www.amazon.com/dp/B00CR9WVPE/ref=cm_sw_r_cp_api_i_VfS6CbNBD59AQ
I had my rims done by a local company, they are the factory 16" painted gloss black. My mazda emblem is actually a long story, but essentially it is just scuffed up with sand paper ready to be painted but I liked the look and stuck it back on the way it is. I have also installed car play, and 3D printed a shift knob. The factory bose system was a little lacking and put a small under seat sub in to help fill the sound, but am still not happy with it, so that's a future project.
Some near future plans for the car include the aero kit, and I'll post the links to those here too:
Front Bumper Lip Air Dam : https://www.amazon.com/dp/B01FTUE8EY/ref=cm_sw_r_cp_api_i_bdS6Cb2X8Y22M
Black Mirror caps : https://rover.ebay.com/rover/0/0/0?mpre=https%3A%2F%2Fwww.ebay.com%2Fulk%2Fitm%2F283050942561
Side skirts : https://rover.ebay.com/rover/0/0/0?mpre=https%3A%2F%2Fwww.ebay.com%2Fulk%2Fitm%2F391544070112
And the rear diffuser : https://rover.ebay.com/rover/0/0/0?mpre=https%3A%2F%2Fwww.ebay.com%2Fulk%2Fitm%2F113007041503
Just put these in your stock headlights.
I just changed the bulbs to brighter ones. Upgrading the entire headlight assembly would be too expensive for me. These are what I got and they are better. Not perfect, but as much as you can expect from only doing bulbs, hope this link works: https://www.amazon.ca/dp/B00U1OL44G/ref=cm_sw_r_cp_apa_i_HxSJDb4W3QPNE
BEAMTECH H13 LED Headlight Bulb, 50W 6500K 8000Lumens Extremely Brigh (9008 Hi/Lo) CSP Chips Conversion Kit
Bonus: reverse LEDs I also installed LUYED 2 X 1700 Lumens
Currently looking into some LEDs that turn the fender flare lights into a DRL of sorts as well.
Did that as well, with an LED replacement.
(https://www.amazon.com/gp/product/B00NPIUFMM/ref=ya_st_dp_summary?ie=UTF8&psc=1)
Pretty easy to replace as well.
Leave the two torx screws under the light alone, but unscrew the 5 hex screws, then you can reach in, and pull the assembly out to replace the bulb.
I can’t help with headlights info, but I have a 2015 3 and did the LED Interior, reverse, license plate and parking lights upgrade. Really pretty easy and much better light all around. I used these and they all are still working great:
https://www.amazon.com/gp/product/B01AHVND32/ref=oh_aui_detailpage_o04_s01?ie=UTF8&psc=1
https://www.amazon.com/gp/product/B01DE7UC6C/ref=oh_aui_detailpage_o04_s00?ie=UTF8&psc=1
https://www.amazon.com/gp/product/B00NPIYDWU/ref=oh_aui_detailpage_o06_s02?ie=UTF8&psc=1
I also bought this toolkit for removing interior the light covers and panels:
https://www.amazon.com/gp/product/B01MUC8LTG/ref=oh_aui_detailpage_o04_s00?ie=UTF8&psc=1
It’s not hard to do and there are very good videos on youtube to guide you, like this one:
https://youtu.be/Hdm9wUFgl18
I am currently looking at these for the turn signals too:
https://www.amazon.com/SiriusLED-resistor-Extremely-Upgrade-Version/dp/B0774HQC8Q/ref=cm_cr_arp_d_product_sims?ie=UTF8#customerReviews
Good luck!
You bet. Not sure of the OEM Projector Housing part #, but they are GM. Bought them used on FB Marketplace. Brand new with only 3k miles on them. $300 total.
Low Beam/Daytime Running Lamps (bulb): H11/H8/H9 LED Headlight Bulbs Low... https://www.amazon.com/dp/B07HCZ7RZ6?ref=ppx_pop_mob_ap_share
High Beam bulbs: HIKARI LED Headlight Bulbs... https://www.amazon.com/dp/B07GKC818Q?ref=ppx_pop_mob_ap_share
DO NOT WORK. Turn Signal bulbs: iBrightstar Newest 9-30V Super... https://www.amazon.com/dp/B06XK4PL33?ref=ppx_pop_mob_ap_share
Side marker light bulbs: 194 LED Bulb 3030 Chipset T10 194... https://www.amazon.com/dp/B07L8CVPCX?ref=ppx_pop_mob_ap_share
EDIT: THE SIGNAL LIGHT LEDS DO NOT WORK!
Deets:
I have these as my reverse lights, and holy fuck they are bright.
I did low beams about 4 months ago. I purchased these. They're a direct swap out for the stock low beam. Ignore the bullshit about "200% brighter," they're about 10% brighter at most, but they don't have any fans which is a huge win.
I know the diode dynamics SL1 bulbs are good, too. I just didn't want to wait 4-6 weeks at the time as I'd just burned out a halogen and was pissed off.
THE MOST IMPORTANT thing I can tell you is: properly re-aim your headlights after the install, regardless of what you get. The ones I bought were really good about glare, and I didn't need to do much. (Sorry for being snarky if you already knew that!)
No they are regular halogens with a permanent blue tint which filters out the yellow components of the light.
Philips H7 CrystalVision Ultra Bright White Headlight Bulb, 2 Pack
Turn signals (front and back): https://www.amazon.ca/gp/product/B0774HQC8Q/
I was hesitant to spend $110 on bulbs, but these things are beasts! plus they have the resistors built into them, so no splicing wires or anything. Totally recommend them
The front bulbs were the easiest to replace, just pop the hood, locate the bulb, twist the housing out and pop the bulbs in. The ones in the back were a bit of a pain. Pop the hatch, and where the door is normally closed, to the inner side of the light houses there's a small plastic panel, that just pops off. Behind it is a set of #10 (I believe) bolts. Undo those. The housing assembly takes some loving to get out, but it just pulls straight back -- I broke a tab off trying to go side to side... It goes back in and latches fine, but, learn from me: it goes straight back... Even though it doesn't seem like it does. Then once it's out, replace the bulbs as usual, reverse the process to put it back in.
Backup Lamps: https://www.amazon.ca/gp/product/B01LX4FMD1/
The backup lamps are just covered by a plastic panel on the hatch door that pops out with a pocket knife or small flat head screwdriver, then the bulb twists out as usual.
​
Most of this was figured out first hand, or from the owner's manual.
​
As for my internal lights so far, I've only replaced the one above the back seats and the ones above the front seats. The back seat ones pop out with a knife super easily, whereas the front ones were more complicated. I took some pictures of that process and uploaded them here: https://imgur.com/a/YJItuhz -- Basically, the whole module (lights, buttons, sunglasses holder, etc) all comes out, then you replace the bulbs from the back side. The bulbs themselves I picked up from Canadian Tire, which was just a run of the mill off the shelf LED bulbs
It is easily twice as bright as the factory setup. far better pattern too.
https://www.amazon.com/Headlight-Relay-Wiring-Harness-Ceramic/dp/B00H5JFHR0/ref=sr_1_9?ie=UTF8&qid=1464810131&sr=8-9&keywords=h4+harness
https://www.amazon.com/HELLA-HLA-H83140171-H4-100-80W/dp/B000COBLKW/ref=sr_1_1?ie=UTF8&qid=1464810209&sr=8-1&keywords=h4+100w
https://www.amazon.com/HELLA-003427811-132mm-High-Headlamp/dp/B001G72VIK/ref=sr_1_4?ie=UTF8&qid=1464810364&sr=8-4&keywords=hella+h4
Order one of each and a second bulb. plug it all in and have awesome light.
Buy a pair of Hella 7" Headlamps (ECE), and this.
The lamp housings are european code (ECE or E-code). Technically not DOT legal in the US-- but is your inspection station going to inspect your headlamp housings?) These have a sharp cutoff so they won't blind other drivers. I've been running them for years and I love them. The pattern is far superior to DOT lamps-- it tends to really throw the light forward from the bulbs.
The wire loom from ARB is made of a much thicker gauge wire than the wires that are currently driving your headlights. The same bulbs will run brighter with this wire loom upgrade, but I found that if you add new housings (with nice clean clear glass and a good light projection pattern), and a pair of high-quality H4 bulbs, your headlights will work with the power of a thousand suns.
For bulbs, I'm currently running Sylvania SilverStars, but in the past I found out about IPF Fatboy II 80W/60W bulbs. The low-beam is actually higher than the high-beam wattage. Not sure why or how that makes sense, but these are a seriously great upgrade. Be warned, they run very hot and are susceptible to vibration damage (moreso than other standard 55w bulbs). Don't expect these bulbs to last more than a year or two. They're intense, though.
Hope that helps, because that's what I did to my Jeep. I also added a pair of Hella driving-pattern auxiliary lights on my stinger and a pair of 4" Delta fog lights on my front bumper.
So installed my fog lights today. It was as easy as some youtube videos made it out to be and I'm quite happy with the complete look now. They do have a slight gap between the plastic trim and the housing but it doesn't bother me. I did make one stupid mistake that I cannot believe I did not notice until everything was installed. I did not get the fog light switch with the auto headlight option since I did not pay close attention to the ebay listing. False advertising by the seller's first image, but also my fault for not looking at it more closely. In case anyone was curious I figured out how to hook up the LED DRLs. Turns out that the red wire goes to + battery, black wire to - battery and tap the yellow wire into the ENG IGN fuse second to the top right corner. I upgraded my headlights to Auxbeam LEDs and they match the DRL quite better than the Kensun LEDs, which are now being used for the fog lights. The Kensun LEDs aren't as bright and shine a bit more upward from the edges compared to the Auxbeam.
Album of parts
Where to buy!
Kensun LED H11
Auxbeam LED H11
Fog Lights
Switch with no auto headlights
DRLs the plastic trim is not the best fitment. Some of the clips don't hold in place but can easily be held comfortably with the use of zip ties.
This is everything I ordered for my '17 Limited a couple years ago. Hopefully the links still work.
Fog lights: https://www.amazon.com/gp/product/B01H8VILMC/
Reverse lights:
https://www.amazon.com/gp/product/B00K3GBRQ2/
Dome lights:
https://www.amazon.com/gp/product/B00AO04VCY/
Trunk lights:
https://www.amazon.com/gp/product/B0087XOTWW/
Visor mirror lights:
https://www.amazon.com/gp/product/B0061TU2JS/
Map and puddle lights:
https://www.amazon.com/gp/product/B00EPA7BXU/
This is everything I use. Haven’t had any issues in 2 years so far. For the tag lights, you can just go to an auto parts place and buy their LEDs.
Low Beams:
https://www.amazon.com/gp/aw/d/B01L1NLWEM?psc=1&ref=ppx_pop_mob_b_asin_title
High Beams:
https://www.amazon.com/gp/aw/d/B01KFBPCYC?psc=1&ref=ppx_pop_mob_b_asin_title
Adapter:
https://www.amazon.com/gp/aw/d/B01J5SCQ1I?psc=1&ref=ppx_pop_mob_b_asin_title
Turn Signals:
https://www.amazon.com/gp/aw/d/B01M26IHAR?psc=1&ref=ppx_pop_mob_b_asin_title
Reverse Lights:
https://www.amazon.com/gp/aw/d/B072FHNZKW?psc=1&ref=ppx_pop_mob_b_asin_title
Fog Lights:
https://www.amazon.com/gp/aw/d/B00N5BAWYK?psc=1&ref=ppx_pop_mob_b_asin_title
These weren't bad at all, replaced both low and high for 50 bucks and didn't take me long to replace them. Clips can be a pain to take off but I would say it's not to bad.
Here is the link for the ones I purchased
Philips H7 Crystal Ultra
They may not look brighter or white when in the sun but at night I do notice a difference.
These are what I'm using and they're great:
https://www.amazon.com/SEALIGHT-Headlight-Bulbs-Package-6000LM/dp/B07K438ZQD/ref=mp_s_a_1_3?keywords=sealight+led+headlights&qid=1555819656&s=gateway&sr=8-3
If you're interested you could change out all the interior lighting to LED. The door courtesy lights. The window visor lights. Trunk light. Parking lights. License plate light. Switching to LEDs will modernize the car.
I used these LEDs
Out of the ten, one was flickering on me. But the others have been working properly. Makes my car look really nice.
The only thing I haven't changed out yet is the side mirror lights because I believe they're quite difficult to change.
The name brand Philips D2R are on sale right now for ~$32 on Amazon.
The brightest D2R is this.
>I can’t see shit at night
Before replacing any bulbs make sure the headlamp lens is clear and not yellowed. If yellowed/hazy then polish it out.
I do not know of LED lights that are heated, but alternatively you can go hella h4 upgrade which I prefer to LED/HID
Relay Kit - https://smile.amazon.com/2-Headlight-Headlamp-Ceramic-Socket-Harness/dp/B06XHSFLTZ
Head lights - https://smile.amazon.com/HELLA-003427811-132mm-High-Headlamp/dp/B001G72VIK
Bulbs- https://smile.amazon.com/HELLA-H4-100-80W-Wattage/dp/B000COBLKW
You'll have really good lights and will melt snow without problem.
I tried these ones from Amazon and were simply toooooo bright in my 2019 F250. No matter how I aimed them, I was constantly being flashed by other drivers -- and not the topless kind of flashing either. :D
​
https://www.amazon.com/gp/product/B06XHCQ8KY/ref=ppx_yo_dt_b_asin_title_o05_s01?ie=UTF8&psc=1
​
I might try some lower level lumens type lights but after tinkering with them for two weeks, I just gave up and went back to the halogens.
LEDs 10 for $10 prime shipped
YITAMOTOR 10 pcs T10 Wedge Samsung High Power 1W NEW White LED Light Bulbs US 194 168 192 921 https://www.amazon.com/dp/B015H3KTYG/ref=cm_sw_r_other_awd_EFY-wbHA2FQT5
For headlights:
For LEDs, I don't recommend them yet for brake or running lights. JDM ASTAR make pretty good conversion bulbs, but they can still cause problems. It's a pretty expensive can of worms.
For everything else, let him decide. Maybe give him some gift certificates or something. He's going to be itching to spend that big wad of deployment cash anyway when he gets back.
https://imgur.com/i8bTBQ6
https://www.amazon.com/gp/product/B075J89RYP/ref=oh_aui_search_detailpage?ie=UTF8&psc=1
God I hope this formats correctly - I am a neophyte.
Exhaust - http://www.ixilusa.com/ixil-l3xb-black-hyperlow-xl-full-exhaust-yamaha-mt-07-2014-2015/
Super deep and loud sound - videos online don't do it justice, its unbelievably loud when the baffles are out. Had to have the cat cut out of it. Be aware they have a cat in the V section before the end of the pipe.
Removed the snorkel covering the airbox - I was told its basically blocks airflow.
ECU Flash / Dyno by 2wheelDynoWorks - https://2wheeldynoworks.com/shop/ecu-flashing-service/15-17-yamaha-fz07-mail-in-ecu-flashing-service/
Nels himself worked on my bike - super stoked (shout out to Nate too) They have the best customer service.
Active Tune - https://2wheeldynoworks.com/shop/ecu-flashing-service/yamaha-activetune-afr-closed-loop-self-tuning-ecu-kit-2/
Tune as you go
Bike side harness - https://2wheeldynoworks.com/shop/ecu-flashing-service/ftlink-v1-1-6-pin-bike-side-harnesses/
For tuning later
Windscreen - https://www.revzilla.com/motorcycle/puig-touring-naked-new-generation-windscreen-yamaha-mt-07-2018
I got light smoke, I think it goes better with the bike and pushes wind over my shoulders even at 80+ mph
Protection - https://tstindustries.com/Womet-Tech-Total-Crash-Protection-Pack-for-Yamaha-FZ-07-MT-07-2015.html
Basically got everything from this except the bar ends
Bar Ends - https://motostarz.com/collections/mt-07-2018/products/rhinomoto-barends-mirror-mounts-for-yamaha-fz-mt-models
Super easy to replace mirrors etc with these - and they add protection
Throttle tube - https://www.amazon.com/gp/product/B005C59NO2/ref=oh_aui_detailpage_o01_s00?ie=UTF8&psc=1
90 to 60 degree conversion - its amazing for the price
Dash Screen Protector - https://www.amazon.com/gp/product/B078SMP4ND/ref=oh_aui_detailpage_o00_s00?ie=UTF8&psc=1
Mirror stem deletes - https://www.amazon.com/gp/product/B07BN8QGPV/ref=oh_aui_detailpage_o02_s00?ie=UTF8&psc=1
Current Mirrors - https://www.amazon.com/gp/product/B01N6GB7DZ/ref=oh_aui_detailpage_o02_s00?ie=UTF8&psc=1
Mirrors in photo - https://www.amazon.com/gp/product/B003RESHVU/ref=oh_aui_detailpage_o00_s00?ie=UTF8&psc=1
I like the CRG Mirrors but they get bumped and are hard to readjust - the cheap ebay/amazon mirrors work great
Headlight replacement - https://www.amazon.com/gp/product/B01H6NZ5QW/ref=oh_aui_detailpage_o01_s00?ie=UTF8&psc=1
Signal replacement LED bulbs - https://www.amazon.com/gp/product/B06XK4PL33/ref=oh_aui_detailpage_o01_s00?ie=UTF8&psc=1
Super bright replacements for stock bulbs - used the original housings, they plug right in
Running light LED replacements - https://www.amazon.com/gp/product/B00JRE38EA/ref=oh_aui_detailpage_o01_s01?ie=UTF8&psc=1
For inside the headlight housing
Tail Tidy - https://www.amazon.com/gp/product/B01BH5YGOM/ref=oh_aui_detailpage_o04_s00?ie=UTF8&psc=1
Flasher Relay for LEDs - https://www.amazon.com/gp/product/B00RM26LXO/ref=oh_aui_detailpage_o01_s00?ie=UTF8&psc=1
Levers - https://www.ebay.com/itm/CNC-Brake-Clutch-Yamaha-MT-07-FZ-07-2014-2018-Adjustable-Engrave-Long-Lever/123350737715?_trkparms=aid%3D555018%26algo%3DPL.SIM%26ao%3D1%26asc%3D20131003132420%26meid%3D17a37c1b2d204ffcba65903d19a97b4a%26pid%3D100005%26rk%3D4%26rkt%3D12%26sd%3D122997203335%26itm%3D123350737715&_trksid=p2047675.c100005.m1851
Passenger peg deletes - https://www.ebay.com/itm/for-YAMAHA-MT07-FZ07-Footrest-Cover-Passenger-Footpeg-Removal-Delete-Kit-2014/253869999740?hash=item3b1bd4c67c:g:3qEAAOSw0JVbm1FQ:rk:1:pf:0
I removed the passenger pegs, needed a bracket to hold the brake fluid reservoir - also cleaned up the pegs
Havent done the brakes yet - going to replace the lines etc with steel braid.
Also want to do a sprocket / chain swap for acceleration
I used a quadlock phone mount for a little bit - but took it off because I was playing with my phone too much.
Valid point. But it’s his car, I won’t tell him what to do with it. At least you can still see his damn brake-lights.
I ‘m really happy with the taillights :) They look great and they were super easy to install. It’s all plug and play since the resistors are already wired in. They’re sold by K2 Motor and they’re super affordable on eBay. Only gripe is that they didn’t come with LED reverse lights, you’re expected to transfer the incandescent bulbs from your old lights. Easy fix, I got these LEDs and they fit just fine (and they’re super bright!)
I switched out all my cabin bulbs with these and have been really happy with them.
I have these bulbs. You do need to be careful how loud the fans are as they get obnoxious and if too loud you can hear them inside the card. These aren't bad.
It's not $1000. You can buy the bulbs on Amazon for $50 each.
​
https://www.amazon.com/gp/product/B00480J4KA/ref=ppx_yo_dt_b_search_asin_title?ie=UTF8&psc=1
These are the HID bulbs I bought for my 2005 - your 2007 may need slightly different ones. If you don't want to do installation yourself, shop around for a place charging sensible prices. I used a place in San Francisco called Luscious Garage that does it for a fixed price.
The LED bulb has a heatsink on the back, making the physical dimensions of the bulb too big for the Honda Fit's housing. You are correct in saying it's the same bulb because it is the H4 equivalent. Other cars use that same style bulb but have larger housings, making it a better match. The Honda Fit is just not one of those cars, unfortunately. I use these bulbs for my Fit
Here are the ones I bought. work / fit / look great in my 2019 Jeep Renegade.
http://www.amazon.com/gp/product/B06XHCQ8KY/
Also 38$ vs. 70$ is a better deal.
It's really hard to capture the glow pictures, but it's super easy to try for yourself, and the LEDs are not expensive.
I replaced the puddle lights under the mirrors, in all four doors, and the reverse indicator lights. They are all brighter than stock and the same white color temperature as the overhead console lights.
Haha, yeah I didn't take that photo. My Bonnie has fabric seats. I believe it is the SE, but I'd honestly have to consult my owner's manual to verify that information. Regarding the lights, I bought these turn signals (only fit in the front, according to Amazon), these for the rear turn signals, and these to help with nighttime visibility (and they are AMAZING!). Everything was very plug and play, and it made me realize that working on my baby may not necessarily be as complicated as I once thought. The only issue I had with the installation of those parts is the hyper flashing of my turn signals, but that seems easy to correct and I've already ordered the resistors recommended by Amazon.
​
Edit: I'll probably end up ordering more for my brights and tail lights once I get some more money to play around with. I've spent too much on those listed above, a seat cover set, floor mats, a headlight restoration kit, and an impact drill. My wife is about ready to kill me! :P
these will fit your car with a slight trimming of one of the mounting tabs https://www.amazon.com/gp/product/B00U32DG4C/ref=oh_aui_search_detailpage?ie=UTF8&psc=1
much brighter than stock bulbs and last a heck of a lot longer than silverstars
Trunk: https://www.amazon.com/gp/product/B0177C3AZ0/ref=oh_aui_detailpage_o06_s00?ie=UTF8&psc=1
Plate Lights (Havent burt out so far for 6 + months unlike the other 10 pairs I have tried. https://www.amazon.com/gp/product/B013TXLTRM/ref=oh_aui_detailpage_o05_s00?ie=UTF8&psc=1
Reverse Lights: https://www.amazon.com/gp/product/B00MUF1APW/ref=oh_aui_detailpage_o01_s00?ie=UTF8&psc=1
Map Lights/dome2/3 (5 of them in the car) https://www.amazon.com/gp/product/B00JIEX722/ref=oh_aui_detailpage_o01_s00?ie=UTF8&psc=1
Resistors (For middle rear light see video below) https://www.amazon.com/gp/product/B00BVOR8PO/ref=oh_aui_detailpage_o08_s00?ie=UTF8&psc=1
Ford led bar upgrade and puddle lights under mirrors (http://www.daytimebrightlites.com/Daytime_BrightLites_Running.php) I didn't do turn signals since I didn't want to mess with the stock wiring of the car.
Dome Light install: https://www.youtube.com/watch?v=RfRpxUjR0c8 (Hardest set to do)
Unfortunately I don't have before and after pics.
I had LEDs in the halogen housings and the distance was better than the Anzos. But there is more width with the Anzos. I plan to get different, better, LEDs to see if I can get more distance.
HID still perform better than LED in projectors, but in my opinion LEDs are easier to install. As seen here: https://www.youtube.com/watch?v=rUxfA7RnK-0
I did not get the switchback set, but I did upgrade all bulbs to LEDs.
Front Turns
Rear Brake
3rd Brake, Cargo, and License Plate
Lastly I use Forscan to address hyper flashing and enable "Bambi Mode" (fogs stay on with high beams). I did not have to splice any wires.
Here is the mobile version of your link
[Sealight Hi and Lo](http://www.SEALIGHT.com/ 9005/HB3 High Beam H11/H9 Low Beam LED Headlight Bulbs Combo Package CSP Chips 6000LM 6000K https://www.amazon.com/dp/B07K438ZQD/ref=cm_sw_r_cp_apa_i_wmWCDbK9XH1M6)
That's really awesome that you say that I bought h4 stuff on Amazon and I'm gearing up to install.
Anyone have any experience? Is this a good setup? Tough to install?
HELLA 003427291 Vision Plus 190x132mm High/Low Beam 12V Halogen Conversion Headlamp
H4 100w Ceramic Fused PnP Heavy Duty Automotive Wiring Harness Headlight Foglight Booster Relay 12v
HELLA H4 12V 100/80W Halogen High Wattage Bulb Off Road Use
One quick question, first off i need to check if my fog lamps are working but can i replace then with some led bulbs. how are these https://www.amazon.com/Philips-X-tremeVision-Light-Fits-Pack/dp/B00U2NHLTI/ref=sr_1_1?ie=UTF8&qid=1468178828&sr=8-1&keywords=Philips+X-treme+Vision+LED
Had to dig them out of my order history... here you go! (-:
Headlights-got a set for MIL's 2010 Forster and FIL's 2006 Forester... https://www.amazon.com/dp/B07FXP4KRS/ref=cm_sw_r_cp_apa_i_CAlzDbM6HHTV4
Turn signals for the front...(Aurora) https://www.amazon.com/dp/B07PY4VDD4/ref=cm_sw_r_cp_apa_i_sBlzDbFYTEF0R
These are the resisters for the turn signals so they don't blink fast...(both cars)... https://www.amazon.com/dp/B00UNG3EXQ/ref=cm_sw_r_cp_apa_i_BClzDbADZV5S6
License plate lights and marker lights (I think he used these for both)... https://www.amazon.com/dp/B0186P1MUW/ref=cm_sw_r_cp_apa_i_9BlzDb01J1YPN
Fog lights for the Aurora, they can be yellow or blue, just have to turn the switch off and back on... https://www.amazon.com/dp/B07DGY4LQK/ref=cm_sw_r_cp_apa_i_UIlzDbSPTJ0EF
Headlights in the Aurora, can be a white/blue or yellow, switch off and on... https://www.amazon.com/dp/B07MF1RY6V/ref=cm_sw_r_cp_apa_i_ZJlzDbQFKK85N
Tail lights/brake lights for the Aurora... https://www.amazon.com/dp/B00NPIUFMM/ref=cm_sw_r_cp_apa_i_JLlzDbYRDS6B4
Sorry all the links are Amazon, hubby works there, so he gets a discount...the rear fog light bulbs must have come from somewhere else though, that's the only thing I can't find in our order history... unless it's the same bulbs as the brakes, there are two on that order...
Alla Lighting 912 921 LED Backup Light Bulbs
https://www.amazon.com/dp/B072FHNZKW/ref=cm_sw_r_cp_apa_i_YtVuDb6H8JP3H
That are supposed to drag on the rotors? And okay...well would something like this be okay? Until I get the money for HID or LED headlights?
https://www.amazon.com/dp/B07BT23WVC/ref=cm_sw_r_cp_apip_xvMSPG3oC81n9
Are these the HIR equivalent to 9006? https://www.amazon.com/dp/B00U32DG4C/ref=cm_sw_r_cp_api_i_aZ0pDbRDGFCTY
No the brightest are Philips X-treme Vision.https://www.amazon.com/dp/B00U1OLK86
But personally I prefer the Philips VisionPlus as they are half the cost. https://www.amazon.com/dp/B00U1OLDRE
I bought a pair of these and these for both low and high beams and have not had one issue with my backup camera.
Usually for fog lights you need to have it wired but Mazda has it pre wired. I installed fog lights as well as have everything LED put in. In terms of the actualy LED bulbs all you need to do it plug them in.
here are the ones I bought.
https://www.amazon.com/Auxbeam-Headlight-Conversion-Bulbs-Chips/dp/B01G16BRJY/ref=sr_1_5?s=automotive&ie=UTF8&qid=1487276487&sr=1-5&keywords=auxbeam
What do you think between these three options:
LASFIT
Aukee
Hikari
Try replacing the stock halogens with one of the Philips Vision series bulbs. The guys on NAM love them and say they really do put out way more light without the added heat issues of some brands.
Philips VisionPlus
Philips XtremeVision
The hard part is finding ones that are short enough to fit under the lense.
I found these:
https://www.amazon.com/dp/B07DRBKCZC/
I can not attest as to their quality or longevity as I just got them, but they fit!
Try one of these bulbs. Aside from that, a pair of driving lights would be the next cheapest option, LED would be the ideal.
http://www.amazon.com/SYLVANIA-SilverStar-Performance-Halogen-Headlight/dp/B0012ETJ1O
SiriusLED 7440 Anti Hyper Flash... https://www.amazon.com/dp/B0774HQC8Q?ref=ppx_pop_mob_ap_share
The ones you posted are more affordable, I chose these because the material seemed more durable and they were. These were a little more pricier.
For my 2018 Honda fit I use this for front 2 side markers, all inside interior lights(4) and license plate lights(2). https://www.amazon.com/NINEO-Interior-Reverse-Courtesy-Sidemarker/dp/B07DRBKCZC/ref=sr_1_2?keywords=cree%2B194%2Bled%2Bbulb&qid=1560735126&s=automotive&sr=1-2&th=1 Also, I put dielectric grease on all the bulb socket https://www.amazon.com/Permatex-22058-Dielectric-Tune-Up-Grease/dp/B000AL8VD2/ref=mp_s_a_1_3?keywords=dielectric+grease&qid=1570710707&sprefix=diele&sr=8-3 warning the cap breaks easy if you over tighten it.
Using reddit mobile so forgive me. I have a different pair of headlights on my RAV4 which use H11 instead of 9005 but this the [LED kit I used](SEALIGHT 9005/HB3 High Beam H11/H9 Low Beam LED Headlight Bulbs Combo Package CSP Chips 6000K https://www.amazon.com/dp/B07K438ZQD/ref=cm_sw_r_cp_apa_i_eiZ2DbRYYT5RC)
I assume you are talking about the low beams. If the housing are stock you need two D2R HID bulbs. Always replace left/right bulbs at the same time.
High beams are 9005.
http://www.modifiedlife.com/2007-subaru-wrx-sti-auto-light-bulb-size-chart/
I bought some auxbeam LED's off amazon, they are super bright, and not overpriced like cyclops. LED light also has a weird way of catching anything reflective, so you can see street signs etc forever ahead of you.
I have this particular model: https://www.amazon.com/dp/B01G16BRJY/ref=twister_B01G8DI306?_encoding=UTF8&psc=1
For backup lights, I switched to these which were much brighter.
For dome lights, I switched to these, which were also much brighter (and whiter) than stock. Power consumption is dramatically less than factory incandescents 0.7W vs. 6.7W so you don't need to worry about battery drain.