Best automotive moldings according to redditors
We found 70 Reddit comments discussing the best automotive moldings. We ranked the 31 resulting products by number of redditors who mentioned them. Here are the top 20.
We found 70 Reddit comments discussing the best automotive moldings. We ranked the 31 resulting products by number of redditors who mentioned them. Here are the top 20.
I have a 19 sport but really wanted an ex for the extras and couldn't get it in time. Seeing it in my color makes me so jelly. That's a clean whip 馃敟
As far as chrome delete goes, here are some links you can use if you want. smoked markers, chrome trim blackout, lug chrome delete, black or carbon handles, this site has stickers for the useless buttons, steering wheel, dash, shifter. I went down a rabbit hole.
I searched for windshield weatherstrip and found this part.
It's also on Amazon
See this video at 3min 17sec where they remove it from the bottom
https://www.amazon.com/3M-03614-Scotch-Mount-Molding-Tape/dp/B002JOVUO0
This is the stuff used in GoPro mounts and you can find it at any auto parts store or Home Depot - maybe even Wal-Mart.
It held my GoPro onto the side of my bike doing 180 down the back straight of COTA so I would think it'll hold some LED strips on, plus it doesn't leave a nasty residue when you remove it with some rubbing alcohol and dental floss.
Ford DV6Z-58519A16-AA - Pin Retaining https://www.amazon.com/dp/B01C39R1H0/ref=cm_sw_r_cp_tai_r8UwCbCPX30S0
This, it's like tape. www.amazon.com/3M-03614-Scotch-Mount-Molding-Tape/dp/B002JOVUO0/ref=pd_sim_263_1open_in_new
Beautost Fit For Mazda 2017 2018... https://www.amazon.com/dp/B07B68XHNX?ref=ppx_pop_mob_ap_share
Washed car, used rubbing alcohol on the area the trim was going on and used a hairdryer to heat up 3M adhesive attached to trim piexes before applying.
etopmia Black Headlights Eyebrow Eyelids Trim fit VW MK7 Golf 7 https://www.amazon.com/dp/B01DZK8YLS/ref=cm_sw_r_cp_apa_gZdozbZSFBG6D (I dipped them to make them matte)
3M 03614 Scotch-Mount 1/2" x 15' Molding Tape https://www.amazon.com/dp/B002JOVUO0/ref=cm_sw_r_cp_apa_T4OuzbQ28WMT9
This should work. Beware it has a little thickness to it. Might be a bit overkill
https://www.amazon.com/Subaru-Accessory-Handle-Molding-Scratch/dp/B00I250MIU/ref=sr_1_4?ie=UTF8&qid=1542342498&sr=8-4&keywords=door+handle+guard
Beautost For Mazda 2017 2018 2019 CX-5 CX5 Chrome Front Hood Grill Cover Bonnet Trim https://www.amazon.com/dp/B073NYCTTR/ref=cm_sw_r_cp_apa_i_2pG0Db0TQ4C94
Thanks! They are from EAG
Ahh ok, I think these are the parts you need:
72410-SF1-003 Right
72450-SF1-003 Left
None of the Honda parts sites seem to carry them, due to the fact they are discontinued. But, Amazon technically lists them on their site and are available for purchase. Says "ships in 1-3 months" which usually means they don't actually have them in stock, nor can they get them. But hey, it's worth a shot if you really need them.
Amazon link (right): https://www.amazon.com/Genuine-Honda-72410-SF1-003-Molding-Assembly/dp/B00LIZJ76O
Amazon link (left): https://www.amazon.com/Genuine-Honda-72450-SF1-003-Molding-Assembly/dp/B00LIYKXR2
Exploded view image (#14): https://www.hondapartsnow.com/genuine/honda~molding~assy~72410-sf1-003.html
Oh, that thing. Use some 3M automotive trim tape to stick it back on. Glue is not going to work well and make a mess of your frame.
​
https://www.amazon.com/3M-3614-15/dp/B002JOVUO0/ref=sr_1_2?ie=UTF8&qid=1542223349&sr=8-2&keywords=3m+auto+trim+tape
I believe the noise is created when the reverse lockout ring makes contact with the inside of the shift knob. I took off my shift knob and placed some foam tape on the inside of it to absorb the vibration and I have no more noise.
This is what I used.
https://www.amazon.com/gp/product/B002JOVUO0/ref=oh_aui_detailpage_o02_s01?ie=UTF8&psc=1
Hey thanks man!
Here鈥檚 the link for the eyelids: https://www.amazon.com/etopmia-Black-Headlights-Eyebrow-Eyelids/dp/B01DZK8YLS
And as for what I鈥檓 lowered on, I just have the APR Rolls Control springs installed.
I used the L bracket method along with some automotive body molding mounting tape. With the tape alone I was unable to pull the tables back apart.
Edit: Figured I should give links to the tape and brackets I used.
Tape
Brackets
You can get either of them at pretty much any hardware store, or auto parts store. Although they will be a bit more expensive.
Yeah, I didn't want to do anything too drastic, just give the car a more luxury feel to it without it being obvious to the average bystander I modded it.
All from Amazon. About 550CAD$ worth.
https://www.amazon.ca/gp/product/B0772BYVRY/ref=ppx_yo_dt_b_asin_title_o03_s00?ie=UTF8&psc=1
https://www.amazon.ca/gp/product/B079294M35/ref=ppx_yo_dt_b_asin_title_o04_s00?ie=UTF8&psc=1
https://www.amazon.ca/gp/product/B076LBT75F/ref=ppx_yo_dt_b_asin_title_o05_s00?ie=UTF8&psc=1
https://www.amazon.ca/gp/product/B073P6FQQK/ref=ppx_yo_dt_b_asin_title_o06_s00?ie=UTF8&psc=1
https://www.amazon.ca/gp/product/B0792FLQD5/ref=ppx_yo_dt_b_asin_title_o06_s01?ie=UTF8&psc=1
https://www.amazon.ca/gp/product/B07B68XHNX/ref=ppx_yo_dt_b_asin_title_o07_s00?ie=UTF8&psc=1
https://www.amazon.ca/gp/product/B0784Q49FC/ref=ppx_yo_dt_b_asin_title_o01_s00?ie=UTF8&psc=1 (Still waiting on this piece, slower delivery, will update post once applied but cetain it'll cap off the look)
3M 3614 1/2" x 15' 0 https://www.amazon.com/dp/B002JOVUO0/ref=cm_sw_r_cp_api_i_klZSDb5TREH44
3M automotive double sided adhesive, thank me later.
https://www.amazon.com/Oak-Leaf-Waterproof-Decoration-Multi-colors/dp/B01E3JWOEI
Led Strip.
https://www.amazon.com/Nexlux-Wireless-Controller-Working-Android/dp/B07116SX41
Original receiver sucks, I got this which allows for more features (like syncing to music) and can be controlled with my phone.
https://www.amazon.com/gp/aw/d/B002JOVUO0?psc=1&ref=yo_pop_mb_pd_t1
Original backing tape wasn鈥檛 the strongest, so I used that to stick it on.
Looks like this. https://www.amazon.com/3M-03614-Scotch-Mount-Molding-Tape/dp/B002JOVUO0
Can be bought at AutoZone too. Has a red backing but the tape is black
2x 23inch Dual Color White-Amber Switchback Headlight LED Tube Strip Light DRL Daytime Running Light & Turn Signal Lamp For Audi-Style Headlight 60CM https://www.amazon.com/dp/B019PNV6KA/ref=cm_sw_r_cp_api_ZkVxyb7RP4S01
I lied, they were $19, not $9
3M body moulding adhesive. Just plan on setting aside plenty of time if you ever want to remove the lightstrip.
3M 03614 Scotch-Mount 1/2" x 15' Molding Tape https://www.amazon.com/dp/B002JOVUO0/ref=cm_sw_r_other_awd_I-qRwb0XJE18E
I got the visors from amazon here
https://www.amazon.com/gp/product/B006QME5XE/ref=oh_aui_detailpage_o07_s00?ie=UTF8&psc=1
As for the black under the door handles, I stole that idea from azxtrek and had them done when I got everything else wrapped. I found these scratch cover guards that might also be worth a try. I plan on buying them when the wrap starts peeling
https://www.amazon.com/dp/B00I250MIU/ref=wl_it_dp_o_pC_nS_ttl?_encoding=UTF8&colid=31G4EFHYDU5EJ&coliid=I2RPOHBXRKEDUH
Specifically either of these should work fine:
http://www.amazon.com/3M-38583-Exterior-Attachment-Tape/dp/B00JR4D7AA/
http://www.amazon.com/3M-03614-Scotch-Mount-Molding-Tape/dp/B002JOVUO0/
Walmart usually carries both and any auto parts store too.
$17 Amazon special.
I noticed this one is lifting a bit on the inside, I may need to redo them.
You may actually be able to find some pre-built projector housings for yours. I looked and looked and looked, and the only pre-built projector housings I could find for the Vue were for year models 07 and up. Mine's an 03.
So I had to build mine. And the parts I used were pretty cheap so you might save money just building your own anyways.
Here's the parts I used
Nilight 2.5" Mini HID Bixenon Projector Lens
2x 23inch Dual Color White-Amber Switchback Headlight LED Tube Strip Light DRL Daytime Running Light & Turn Signal Lamp For Audi-Style Headlight
RetroRubber OEM Grade Butyl Headlight Sealant, Black
Everbrightt 1-Pair White 70MM 60SMD COB LED Headlight Angel Eyes Bulb Halo Ring Lamp Light With Housing
2pcs 12V HID Xenon AC Car Ballast 55W HID Xenon Bulbs Lamp For Auto Headlights For H1/3/4/7/8/9/10/11 9005 9006
HID-Warehouse HID Xenon Replacement Bulbs - H1 8000K - Medium Blue (1 Pair)
The paint I used was just a can of Rustoleum semi gloss black I got at Walmart for a few bucks.
I also purchased a separate set of headlights to do all this with, as this was my first time. I wanted to be able to take as much time as I needed with it. I can also easily switch back to stock at any time for whatever reason. I would suggest you do the same, if you're planning on building them.
To get them apart, I preheated our kitchen oven to 220 degrees. I lined an old baking pan with a wet towel and set the headlight on it, then put it in the oven for 10 minutes. This will soften the sealant enough so that you can pry the light housing apart.
Then when you're done with all of your modifications, remove as much of the old sealant you can and then line the edges of the housing with the new sealant. Heat it up like before and compress it back together.
If it's the touchless kind then yeah. I used this 3M adhesive to install them and it's insanely strong.
The car washes with big brushes would probably scratch the hell out of them just like they do to your paint. You really shouldn't use those things.
3M. Do NOT use super glue!!!
This tape will work too. Also available in 1/2 inch. Follow the instructions to the letter.
super strong magnets and some 3m automotive adhesive
www.kjmagnetics.com
http://www.amazon.com/3M-03614-Scotch-Mount-Molding-Tape/dp/B002JOVUO0/ref=sr_1_1?s=automotive&ie=UTF8&qid=1398014445&sr=1-1&keywords=3m+automotive+tape
This is the one I got from Amazon. Not sure how the OEM spoiler is shaped on the underside as mine is a different aftermarket spoiler, but this size should work for you. There are videos on YouTube you can check out for prepping and tips on applying it.
it was this part https://www.amazon.com/MAZDA-MIATA-1990-2005-RETRACTABLE-LATCH/dp/B009SEQ5LC
I haven't tried either of these but they both have been recommended for other cars. The problem is I'm not sure how much you'll need. I also need to redo mine so if you find something that works let me know.
https://www.amazon.com/dp/B00FWJ8Z7Y/
https://www.amazon.com/dp/B00BJLWPAC/
Best tape for the job
I've replaced mine at least 3 times. Captured the piece last time and glued it on with silicone and it's lasted longer than any of my other ones. I got mine from Amazon, around $30 for the whole corner piece IIRC. Super easy to install just snaps on and off.
​
Edit for link : Amazon
Eyelids are from Amazon
https://www.amazon.com/etopmia-Black-Headlights-Eyebrow-Eyelids/dp/B01DZK8YLS/ref=mp_s_a_1_1?keywords=gti+eyelids&qid=1559095312&s=gateway&sprefix=gti+eye&sr=8-1
Tail lights from here, but you can get from multiple sites. I have the Helix ones but they also sell the Ed reps. They are pretty much the same. It's the same vendor.
https://www.fastuningstore.com/products/vw-mk7-golf-gti-golf-r-helix-mk7-5-replica-led-taillights
Nice yah I like the Mudflaps plus it helps keep the sides clean.
http://www.amazon.com/Carbon-Fiber-Style-Molding-Exterior/dp/B00VKQB1B0/ref=sr_1_13?s=automotive&ie=UTF8&qid=1458602784&sr=1-13&keywords=Carbon+fiber+trim+3m Something like that only shorter
https://www.amazon.com/Genuine-15932239-Pick-Molding-Upper/dp/B00GUH0QO2
https://www.amazon.com/Genuine-GM-Molding-Part-15932238/dp/B00TAB80UC
I would contact their CS team and see what they say.
I like using adhesive for fans too. 3M makes a high strength adhesive tape used for attaching trim on cars. http://smile.amazon.com/3M-03614-Scotch-Mount-Molding-Tape/dp/B002JOVUO0
5 foot should be plenty, but it's really not that much more to buy 15 feet. Just some small squares on the corner and they won't come off without some serious pulling.
Googled 2002 Camry xle interior panel clips, got this
https://www.amazon.com/Genuine-Toyota-Inside-Opening-Moulding/dp/B00IGCUGXK
Here!
You can purchase 3m VHB tape from any automotive shop like Autozone or Oreilly's. Or you can purchase online Amazon or eBay.
https://www.amazon.com/3M-3614-15/dp/B002JOVUO0/ref=pd_cp_263_2?pd_rd_w=JrmWN&pf_rd_p=ef4dc990-a9ca-4945-ae0b-f8d549198ed6&pf_rd_r=RWNW0JS1E97V0ZSEQF1R&pd_rd_r=b32cd8a4-66e7-11e9-8627-41445435c50e&pd_rd_wg=7onNN&pd_rd_i=B002JOVUO0&psc=1&refRID=RWNW0JS1E97V0ZSEQF1R
This stuff would work, maybe? https://www.amazon.com/3M-3614-15/dp/B002JOVUO0?th=1&psc=1
If you wanted to reduce the waviness of the metal you could attach a thick piece of molding between the metal and white topper
My first thought (although a somewhat off-label use) would be 3m VHB trim and molding tape like this: https://www.amazon.com/3M-3614-15/dp/B002JOVUO0. As long as both surfaces are perfectly clean (as in wipe them down with alcohol before applying), I'd be shocked if it didn't hold up as least as well as whatever the holder came with. It's fairly ridiculous stuff.
I'd go with something like that being somewhat flexible over an epoxy of any sort, the flexibility might help it last longer. I would bet that 3M 5200 would work as well (it's a marine adhesive sealant) but it'd be more of a PITA to work with than the VHB tape.
It's not the seals... I had a car that had this happen to. It was late last night I I didn't want to post and link to pictures.
First you would remove the plastic covering the a pillar on the inside like this
If you remove this it will look like this, you might have to scroll to see the roof. So near the front of the car you'll run a water through this channel. And wait for it to leak. Once it does you'll know where about the leak is at.
Run the water hose slow and start at the windshield and work you way back waiting about 2 minutes before moving the water hose back.