(Part 3) Best recording studio environment equipment according to redditors
We found 1,095 Reddit comments discussing the best recording studio environment equipment. We ranked the 264 resulting products by number of redditors who mentioned them. Here are the products ranked 41-60. You can also go back to the previous section.
https://www.amazon.com/Level-Pack-Acoustic-Panels-Studio/dp/B07BX3K3ZD
Hang them with command strips so you can remove them easily. $10 that will save you so much headache in any close neighbor situation
Hi, my dude. I have advice you need.
Dig how The Golden Voice guy speaks when doing his street bit. He gets how to speak - it's not just the voice, he changes his tone and inflection as he does his 'impression'. Tone, pacing, and inflection are big tools you can use to leave people engaged in your videos, in ways where they'll leave them on in the background, and rack up views. The way you're doing it now, there's obvious passion and interest, but once I've got your info, that's going to be it.
The all-time greatest at this is Casey Kasum - that's actually a link to his blooper reel, and you can hear how the way he talks shifts between his professional voice, and his more casual way of speaking (and also it's just really interesting hearing the voice of Shaggy from Scooby Doo going off in a profanity-laced tirade over a "fucking dog"). When you're done with the gag reel, take a listen to his short ABC Special. He actually gives some great voice performance tips in it, and it shows the level he puts in.
A really brilliant example is the Forgotten Realms videos. His voice is similar, but he takes the time to pace things out, control his words, and draw people in with the inflection. It's classic radio voice, and I've got to tell you, I have put these videos in the background and forgot about them. So often I'd actually threw him cash. The guy gets it - it's a shame the videos aren't getting the return he values his time at, because the quality is top notch.
Consider getting a good mixer, and then just playing with it's volumes, getting used to how the adjustments sound. You want to sound clean and clear off your microphone - a mixer can help with that. You might also consider constructing a soundproof box for your mic, or investing in a (relatively inexpensive) booth shield for your mic. That'll take a lot off the fuzz in your voice, and give you cleaner, crisper recordings. I'd also take the time to look into a pop filter. It' a low-cost product that'll help you get crisp, clean enunciation (and correct emphasis) with your "B"s, your "P"s, and your "T"s. Trust me - being to fire off B, P, and T words cleanly and crisply will draw people in. There's something alluring about the pop letters, but for recording, those same words can throw you off completely.
I'd also take a look into playing with your recording software - a lot have features built-in that can compensate for what I've been suggesting, because most people are just amateurs who want quality-sounding audio. They'll never sound as good as the physical solutions I'm offering (and I'd really suggest sticking to those), but it'll improve the tone of your videos by a lot (and net you views) if you take the time to go for polish.
Content-wise? I hate to say it, but I never, ever play black. :D
I'd be the wrong guy to make suggesting on your takes on the cards. But I hope that studio advice helps a bit.
I mostly used this guide - https://tombuildsstuff.blogspot.com/2014/02/diy-server-rack-plans.html?m=1
The 20U rails on Amazon - Reliable Hardware Company RH-20-SRR-A 20U Full Hole 20 Space Rack Rail Pair https://www.amazon.com/dp/B00JJ18OVS/ref=cm_sw_r_cp_apa_i_hPG7Ab276K7A2
The wheels on Amazon - Swivel Caster Wheels Rubber Base with Top Plate & Bearing Heavy Duty with Total Lock Brake Pack of 4 Black by Online Best Service (2.5" With Brake) https://www.amazon.com/dp/B01N45QP3Z/ref=cm_sw_r_cp_apa_i_0PG7AbTNSG1AW
The shelf on Amazon - AC Infinity Vented Cantilever 2U Universal Rack Shelf, for 19” equipment racks. Heavy-Duty 2.4mm Cold Rolled Steel, 100lbs Capacity. https://www.amazon.com/dp/B01C9L3K18/ref=cm_sw_r_cp_apa_i_LQG7Ab7SMH2JA
The wood I got isn't normal 2x4's, but instead 1 1/4 x 3 pine. It's the wood in the back of Home Depot that costs $20 per 8 foot board but worth it due to them being a lot straighter. I used 4 boards to complete this.
I used 2" Kreg screws with my Kreg Jig. The mounting depth for the rails is 21.5".
In a pinch I've used rack shelves from places like Fry's. Is that an option? Something similar to: https://www.amazon.com/AC-Infinity-Cantilever-Universal-Heavy-Duty/dp/B01C9KYUG8
OP gave the link in a comment not far below this one: https://www.amazon.com/dp/B07CGWHFZM/ref=cm_sw_r_cp_awdb_t1_TmCZDbHGA8Q6J
Thanks man, please see; https://www.amazon.com/dp/B07CGWHFZM/ref=cm_sw_r_cp_awdb_t1_TmCZDbHGA8Q6J
"Fire Retardant: CA Technical Bulletin 117"
https://www.amazon.com/gp/product/B07CGWHFZM/ref=oh_aui_search_asin_title?ie=UTF8&psc=1
🤷🏼♀️
​
Fine, I'll get some mineral wool.
Its acoustic foam, sometimes sold as squares or as full panels
https://www.amazon.com/Charcoal-Acoustic-Panels-Studio-Wedges/dp/B074JJV1GC/
Here are some "Rack Essentials"
Shelfs/Rails:
https://www.amazon.com/NavePoint-Adjustable-Mount-Server-Shelves/dp/B0060RUVBA/ref=sr_1_1_sspa?ie=UTF8&qid=1510637469&sr=8-1-spons&keywords=1u+rack+rails&psc=1
https://www.amazon.com/Navepoint-Fixed-Vented-Server-Adjustable/dp/B01A6JQYDG/ref=sr_1_6?ie=UTF8&qid=1510637496&sr=8-6&keywords=1u+rack+shelf+sliding
https://www.amazon.com/Navepoint-Sliding-Vented-Server-Adjustable/dp/B01A6JQPFI/ref=sr_1_8?ie=UTF8&qid=1510637508&sr=8-8&keywords=1u+rack+shelf+sliding
Drawers:
https://www.amazon.com/NavePoint-Server-Cabinet-Locking-Lockable/dp/B009WS7TSW/ref=sr_1_4?s=musical-instruments&ie=UTF8&qid=1510637549&sr=1-4&keywords=1u+rack+drawer
Fans:
https://www.amazon.com/AC-Infinity-CLOUDPLATE-Airflow-cooling/dp/B00ZQPDB7I/ref=sr_1_5?s=musical-instruments&ie=UTF8&qid=1510637586&sr=1-5&keywords=rack+fan
Switched PDU
https://www.amazon.com/Eliminator-E107-Control-Center-S-Switch/dp/B000GASJF2/ref=sr_1_1?s=musical-instruments&ie=UTF8&qid=1510637607&sr=1-1&keywords=individual+switch+pdu
Maybe you will find some of that stuff useful...
Not sure if anyone has made any comments about your monitors sitting on the desk, though I'd highly recommend both getting some isolation foam for them, as well as moving them away from the wall as they have a rear-facing bass port. You'll also want to angle the cones at your ears in your normal seating position to get the best sound quality out of them. Here's an article from E-Home Recording Studio with some rough recommendations on the subject.
Studio monitors are great speakers, but they're designed for a very-specific use case. If you aren't using them for production in some capacity, you can still take advantage of their rich sound quality if you set them up correctly. For example, I have a pair of KRK RP5G2s on my desk. While these do have a thin layer of isolating foam under them, I've still opted to place 2pair of that auralex foam under them. This way, I've got them angled right at my ears from where they are on the desk--and how low it is compared to my seating position. I've not done any additional treatment to my room, though I can only really hear major bass collection in the corners when I really crank the gain.
All-in-all, though, you setup looks great. The table is especially attractive...though if only it was in black (or something)...
> How do I get a server rails fit on this?
Most of the time you won't be able to. Server equipment is generally meant for square-hole racks, and most OEM rails will not fit a round-hole (telco/network) rack.
What you can do is buy L-bracket rails for servers to sit on. The servers won't clip or lock in, but at least they're supported. I would not stack too many servers on a single set of L-brackets though.
From Amazon, it's a NavePoint 1U Cantilever shelf
There are plenty of generic rack rails available. Here's an example: https://www.amazon.com/CyberPower-4POSTRAIL-4-Post-Universal-Mount/dp/B00TCELZTK
Acoustic Foam Egg Crate Panel Studio Foam Wall Panel 48" X 24" X 2.5" (4 Pack) https://www.amazon.com/dp/B07CGWHFZM/ref=cm_sw_r_cp_apa_D.V-Bb2ZC5N0M
In your choice of colours.
They claim that this product is fire resistant, I haven’t tested it. But the case is very quite.
New Level 12 Pack- Acoustic Panels Studio Foam Egg Crate 1" X 12" X 12" https://www.amazon.com/dp/B07BX3K3ZD/ref=cm_sw_r_cp_api_i_xjg1Cb9SM0CBP
These are the typical ones:
https://www.amazon.com/KING-DO-WAY-Isolator-Isolation/dp/B017UC162Q/ref=sr_1_4?ie=UTF8&qid=1501542145&sr=8-4&keywords=speaker+pads
Kinda pricey for what they are, though. You can likely just buy the foam yourself at a craft store and cut to size for a lot cheaper.
This is my new ethernet networking hub in the new house. I had two Cat6 and one RG-6 pulled to every drop and have 14 drops throughout the house. All of the ethernet drops (red and yellow in the top right of the picture) run to this cabinet and the RG-6 go to a panel to the lower right of this with the cable modem and firewall (pfSense). The house is a two story with a walk out basement and this cabinet is in a storage room next the to the stairs in the finished basement.
Equipment:
Accessories:
Equipment not shown:
The D-Link is currently for the PoE VoIP phones and PBX. The Cisco switch is for everything else in the house for now. There is a Drobo camping on the top of the cabinet which will be decommissioned eventually and content moved to a FreeNAS server. Current power draw from everything here including Drobo is 85W.
Cross-posted in /r/HomeNetworking
edit: forgot to mention that the fiber line runs to the den where the lab will be setup. Currently the other end is another Cisco SG500-28 (the model without the fans, so quiet). Future upgrade is a 10G connection.
I don't anticipate either of those options making an impact. I think your need is coming from behind (i.e. the room). Below is a link to Warren Huart discussing vocal recording in general. Skip to around the 4:40 mark give or take, and he has a great explanation of where to buffer reflections for home recording https://youtu.be/x_Zsn8wq5Js
As it stands, I think you might be better off getting something like this: https://www.amazon.com/dp/B01GAMP2S6/ref=cm_sw_r_cp_awdb_y9CRzbRC3YZ7X
That way you could mount them on the walls to kill some of the reflections. I glued them on some foam board from Hobby Lobby and nailed the boards on the walls. This drastically deadens the space. That way, I'm getting clear recordings. Remember, you can always add an effect in post, but it's harder to reduce or remove a printed effect. Hope this helps.
After a quick Google search, seems like they are speaker isolation pads like this: https://www.amazon.com/dp/B01B6ZIGBC/ref=cm_sw_r_cp_apa_i_dLN6Ab1TMYEXD
Generic Amazon Panels:
https://www.amazon.com/gp/product/B01JNAXIII/ref=oh_aui_detailpage_o02_s00?ie=UTF8&psc=1
I'm not quite sure how much they're actually doing.. .but it looks cool at least..
Martin Logan Motion 35XT and https://www.amazon.com/gp/product/B07CGWHFZM
The KEFs are dope! I have an employee discount at BBY so the Martin Logans were an easy choice but KEF is great from what I've heard.
Good eye - I actually have 3 different types. The blue and black ones that I already linked, 4 of the corner pieces, and 20 of the bigger, higher quality foam that I didn't buy from Amazon. Let me see if I can dig up the details of what they were.
You're probably aware, but might want to put some isolation pads under those monitors, since currently the cardboard boxes are adding their own vibrations to the mix. I use these and it honestly makes a huge difference for me. Everything just sounds so crystal clear with them.
The sellers tend to bounce around but a 13 pack can be found here. These are the ones I’ve got. https://www.amazon.com/gp/aw/d/B074JJV1GC/ref=mp_s_a_1_12?ie=UTF8&qid=1522514342&sr=8-12&pi=AC_SX236_SY340_QL65&keywords=sound+panels+for+walls
This is sexy as fuck. I'd recommend getting some foam isolation pads for the speakers that can angle them a bit upwards, and then point the speakers at you a bit.
Nice setup. All you need, really. Consider getting some foam to tilt the monitor right at your ears: https://www.amazon.com/KING-DO-WAY-Isolator-Isolation/dp/B017UC162Q
The NavePoint 22U IT Wall Mount Network Server Data Cabinet Rack Glass Door Locking Casters comes with both casters and wall mount hardware. You can run it with any combination of sides, back and door. Buy one that's a bit bigger than you think you need. Buy some StarTech 2U Universal Vented Rack Mount Cantilever Shelf for 19-Inch Server Racks shelves and maybe a drawer
DaVinci resolve (free) should work.
Since you are doing voiceovers use your resources first to get a USB microphone, I have not used this model but I looked for something under $150. You can record direct to your computer.
If your budget allows look into shock-mount/pop filter and a sound isolation shield
You mean like this?
Your mic is great in soundproof rooms. https://www.amazon.com/Microphone-Soundproofing-Griffin-Soundproof-Insulation/dp/B0082DAL3S
Link without the tracking garbage, https://www.amazon.com/Studio-Monitor-Isolation-Pads-Suitable/dp/B07DCQW156/
OP, angle instead of raising.
Yes, you can get something cheap like these foam pads.
https://www.amazon.com/Speaker-Monitor-Isolation-Dampening-Stabilizer/dp/B01B6ZIGBC/
You can also use all kinds of things laying around that are similar in height, like text books, tuna cans and bananas.
It also looks like one speaker is toed in more than the other, you can play around with that a bit but try to keep them on a similar angle to each other as a proper position will give you a good center image.
Noise cancelling head phones (with or without music playing) and a white noise machine or fan may really help. Maybe move your bed to a wall farther away from the source of the noise, if it isn't already as far as possible.
Other than that, there's not much you can do. I know your pain, though. Growing up with noisy siblings and neighbors, paired with thin walls, was a living nightmare. I regularly daydreamed about bombing their stereos and televisions just so I could imagine getting some peace and quiet.
Edit: You can put up some soundproofing foam panels like this or hang thick quilts on the walls as well. This should help insulate from a fair amount of outside noise. :)
Maybe look into getting some isolation Pads for your speakers to cut down on any resonance from the dresser and in case any vibrations make it through to your turntable.
What he said: heavy stuff up top makes it easier to tip over.
Generally, if they are only 12-18ish inches deep and don't come with rails, then they're fine with being on two posts.
If you are still uncomfortable for whatever reason feel free to buy some 4-post shelves.
Even 2-post shelves are usually rated for 50#, some for 100#.
Edit:To secure the Yamaha receivers, I might consider unscrewing the feet and drilling some holes in a rack shelf or rails to bolt into the same. This way everything can be secure if you have to move the rack around.
Edit 2: Lastly, and I'm sure you know this, some of these receivers call for 30cm of space above for proper ventilation: they're not designed for rack mount. So I would mount some fans on the back and close any excess open slots to pull air across the top of the devices.
The AT2020 is definitely a solid choice for Vox. The 2050 is more versatile with switchable modes, but if you are only recording vox, the 2020 should serve you very well at that price range.
A pre-amp is what takes the very quiet, low-level signal from your microphone and boosts it to an acceptable level. Most interfaces have a preamp, and then convert the signal to digital, transferring it over USB or Firewire. You won't be able to use your mic properly without one. (you can get by with a mixer and a soundcard, aka a preamp and a soundcard Analogue-to-Digital converter, but an interface is absolutely the way to go).
However, you can forgo the interface if you don't see yourself going beyond one mic in the forseeable future, and get the AT2020 USB, which is the same thing, but has all of the necessary preamp/digital conversion you need already in the package. Please do note, though, that an interface will allow you to connect any mic, or a guitar, or a keyboard, even MIDI, which, if you have any plans to expand, even a little, is a must.
As far as interfaces go, I recommend focusrite, such as this
What you are describing is commonly known as acoustic treatment. Its partially to reduce reverb, but even more so to "balance" the sound of your room out. Carpeting will help particularly in small rooms with low ceilings. If you are only doing vocals and other smaller projects, something like this will help with that. Either way, you will likely want a pop filter, which helps remove plosives (p,b,s,t).
You should check /r/audioengineering to get the best advice!
Something like these may help. Not sure if you'll need more, but there's also a 48 pack for less than double the price. Not sure about the effectiveness of 1 inch vs 2 inch pads though
I cannot confirm about the Norco ones specifically, but I got a set of these link for some supermicro chassis I have.
Much better than spending the 70 dollars for official ones.
Put sound panels on it
https://www.amazon.com/gp/product/B01JNAXIII/ref=oh_aui_detailpage_o00_s00?ie=UTF8&psc=1
Got them from Amazon https://www.amazon.com/gp/product/B01GAMP2S6/ref=oh_aui_detailpage_o01_s00?ie=UTF8&psc=1
To mount them I just bought a can of spray adhesive. It all went up pretty easily.
Here's our space: https://i.imgur.com/BcBpnEv.png
I prioritized room treatment to minimize echoing since we're recording an audio drama (improv comedy sci-fi) and quality vocals are a must. The sound panels behind each seat are these acoustic panels from Amazon mounted to tri-fold foam core display boards from the dollar store.
Our show is Dispatches from the Multiverse, if you're interested to hear how it sounds ;)
I ordered one of these racks about 2 years ago when I wired up my house and finished my home office:
https://smile.amazon.com/gp/product/B01A6JQV8Y/ref=oh_aui_search_detailpage?ie=UTF8&psc=1
my only hangup on it (and you can actually see it on a review) was that the screws that came with the rack were junk, and I had to go out to get new ones that actually would fit right.
also using:
this patch panel - https://smile.amazon.com/gp/product/B0072K1OWY/ref=oh_aui_search_detailpage?ie=UTF8&psc=1
this shelf - https://smile.amazon.com/gp/product/B008LUW4CI/ref=oh_aui_search_detailpage?ie=UTF8&psc=1
and this cable manager - https://smile.amazon.com/gp/product/B01HJTTOH4/ref=oh_aui_search_detailpage?ie=UTF8&psc=1
​
wish I had photos of the little get-up in my closet for you. I've got a basic 4-outlet battery backup powering my ISP modem, my router, managed 24 port switch, and the seagate single-drive NAS we use.
one day i'd like to get one a bit bigger so it can also support the pi server that's also sitting on that shelf and the POE injectors for my APs.
Thank you! I purchased these, and these for the corners:
https://www.amazon.com/gp/product/B01C9F83QQ/ref=oh_aui_detailpage_o00_s00?ie=UTF8&psc=1
https://www.amazon.com/Acoustic-Foam-Studio-Soundproofing-Corner/dp/B071XNPW6G/ref=pd_sbs_267_1?_encoding=UTF8&pd_rd_i=B071XNPW6G&pd_rd_r=A1CPFEV7C5JFMCAHZFM8&pd_rd_w=dhXGn&pd_rd_wg=4sqPT&psc=1&refRID=A1CPFEV7C5JFMCAHZFM8
Honestly it's 99% decoration. You'd want to order a thicker model in higher quantity.
https://www.amazon.com/A2S-Protection-Acoustic-Insulation-Quality/dp/B01GAMP2S6/ref=sr_1_1?ie=UTF8&qid=1474819839&sr=8-1&keywords=sound+dampening+foam+48 a couple sets of these might work.
Happy humping ;)
you would likely need an additional power source, IE, solar panels and a deep cell battery, an isolator, or else a generator. Sound proofing it wouldn't be difficult since its a small space. You would have to start from the bottom with proper sound proof material like some [rattle trap] (https://www.amazon.com/dp/B00DYAF9FY/ref=wl_it_dp_o_pC_nS_ttl?_encoding=UTF8&colid=28XYGYZEEI9GN&coliid=I3FV8PPDJWQ5BU&psc=1) and or thicker panels in the build then once the walls are in you could get some sound [foam panels] (https://www.amazon.com/Charcoal-Acoustic-Panels-Studio-Wedges/dp/B01JNAXIII/ref=sr_1_1?ie=UTF8&qid=1474918666&sr=8-1-spons&keywords=acoustic+foam+panels&psc=1) and such to hang up inside. Its possible with the knowledge and the proper funds to do it.
is this what you mean by a diffuser? https://www.amazon.com/Microphone-Diffuser-Isolation-Absorber-Griffin/dp/B0082DAL3S?ie=UTF8&*Version*=1&*entries*=0
if so, that's what i was referring to when i said 'reflection filter'! i wasn't sure what they were called and by googling random words i found someone refer to it as reflection filter a couple times so i just posted that. but yeah a diffuser is exactly what i was thinking of. i'm not the best at articulating myself with regards to these things but yeah basically it seemed to me like i was recording and the sounds would echo and bounce off of different parts of the room (it's a large-ish room in which i record) and come back to the mic and just give it a muffly sound, so maybe isolating the mic off with some sort of padding behind it might be useful so that sounds aren't bouncing around like that. based on your and cesarjulius' responses though i'm wondering if maybe i have the wrong idea about what's actually going on when i record
http://www.amazon.com/Auralex-MudGuard-Isolator-Dampening-Charcoal/dp/B004VM5R7Y/ref=sr_1_3?ie=UTF8&qid=1411506338&sr=8-3&keywords=mudguard
the video review under "most helpful reviews"
this is the type of thing that makes me wary of cheaping out or buying a product with mixed reviews
12 Pack- Charcoal Acoustic Panels Studio Foam Wedges 2" X 12" X 12" (12PCS, Black) (30305cm, Black) https://www.amazon.com/dp/B076NSFQ75/ref=cm_sw_r_cp_apa_i_Y0RxDb4VMJY8W
This is really all I can think of but its not very visually appealing.
I’m 6 foot even. Here is a link to the acoustic foam I bought:
Foamily 12 Pack- Red/Charcoal Acoustic Panels Studio Foam Wedges 1" X 12" X 12" https://www.amazon.com/dp/B074JJV1GC/ref=cm_sw_r_cp_api_i_xPjuDbD098Y4G
Here you go:
https://www.amazon.com/dp/B01C9KYUG8?ref=ppx_pop_mob_ap_share
yah that’s a definite advantage to the rast. i use the Odyssey racks for doing that but they are like 4x the price of the rast rack. the build for the rast rack looks pretty straightforward maybe i could do it (not handy with wood)
these are really handy for strapping non-rack gear to:
InstallerParts 2U 19" 24 Port Blank Panel for Keystone Jack https://www.amazon.com/dp/B008NXJI2M/ref=cm_sw_r_cp_apip_TinFW8HTPAXJR
here’s the rack drawers i use, you can run cables out the back for permanent install:
NavePoint Server Cabinet Case 19" Rack Mount DJ Locking Lockable Deep Drawer with Key 2U https://www.amazon.com/dp/B009WS7TSW/ref=cm_sw_r_cp_apip_eyb4x2Ct3B1Bk
Check out some of the stuff from Auralex -- like this reasonably-priced setup: http://www.amazon.com/Auralex-MudGuard-Isolator-Dampening-Charcoal/dp/B004VM5R7Y/ref=sr_1_6?ie=UTF8&qid=1412014187&sr=8-6&keywords=auralex
That could be enough to reduce the ambient sound that gets recorded in your mic. If that's not enough, a few well-placed Studiofoam panels on stands would help too. And it would all be portable if you decide to go record somewhere else.
Please be very careful if you decide to go with lower-cost wall treatment options. The Station Fire wasn't that long ago.
Thanks!
Sound absorbing (or in some cases, diffusing) pads. When I ripped the carpet out if this room and installed the solid floor it threw the acoustics way out of whack, so I definitely had to do a little treatment. The rug helps, too.
Example:
https://www.amazon.com/dp/B076NSFQ75/ref=asc_df_B076NSFQ755425474/?tag=hyprod-20&creative=395033&creativeASIN=B076NSFQ75&linkCode=df0&hvadid=198093834376&hvpos=1o2&hvnetw=g&hvrand=4672421092785182867&hvpone=&hvptwo=&hvqmt=&hvdev=m&hvdvcmdl=&hvlocint=&hvlocphy=9031686&hvtargid=pla-390387946052
https://www.amazon.com/Auralex-Acoustics-MOPAD2PK-Acoustic-Isolation/dp/B009EPP1EM
These Auralex foam pads are designed exactly for this. There's probably a cheaper knockoff out there or you could diy with some foam or some wood cut in similar shapes. They also mitigate vibration. I'd recommend adding a piece of rubber or dense foam to the top of the stands either way to reduce vibration and movement of the speakers on your stands.
Yeah man you can use blankets n stuff if you don’t have the money or option to buy foam panels and put them on the walls.
here’s a good option too. This paired with hanging thick blankets around the room will probably be your best bet.
Try hang rugs or tapestries if you don’t want to do anything permanent. You could also put sound proofing foam on the walls too. Something like this
https://www.amazon.com/48-Acoustic-Panels-Studio-Wedges/dp/B00TP52HCK/ref=asc_df_B00TP52HCK/?tag=hyprod-20&linkCode=df0&hvadid=241985258521&hvpos=1o1&hvnetw=g&hvrand=1921050125587974333&hvpone=&hvptwo=&hvqmt=&hvdev=m&hvdvcmdl=&hvlocint=&hvlocphy=9005904&hvtargid=pla-617623670824&psc=1
What about this? It says it suports up to 100 pounds each which is more than enough
https://www.amazon.ca/AC-Infinity-Cantilever-Universal-Heavy-Duty/dp/B01C9L3K18/ref=pd_sim_267_5?_encoding=UTF8&psc=1&refRID=05M32TV9VHAJA3FB2BBQ
The room is in a closed crawlspace and no pets or anything will be in there. Also, we don't plan to add more RAM or make any changes in the future so being able to slide it in and out is not a problem.
Those storage arrays look cool but we really only need 4 slots of the r710 plus 4 other slots.
The company doesn't make rails, so would that shelf cantilever thing work too?
This still work better.
48 Pack Acoustic Panels Studio Foam Wedges 1" X 12" X 12" https://www.amazon.com/dp/B00TP52HCK/ref=cm_sw_r_cp_apa_i_qsBBDbP4P74CK
Maybe a wall mount rack frame + server shelf.
Sure thing!
It's these: 12 Pack- Ice Blue/Charcoal Acoustic Panels Studio Foam Wedges 1" X 12" X 12" https://www.amazon.com/dp/B01JNAXIII/ref=cm_sw_r_cp_apip_u8qdwpHWEOjYA
Attached to this: Privacy Room Divider https://www.amazon.com/dp/B00CKR1TOC/ref=cm_sw_r_cp_apip_CH9flAoVyTGaE
Using this: Acoustic Foam Spray Adhesive Glue Can https://www.amazon.com/dp/B00WJ1AV0W/ref=cm_sw_r_cp_api_tAfPzb52D37JY
https://www.amazon.com/dp/B076NSFQ75/ref=asc_df_B076NSFQ755411530/?tag=hyprod-20&creative=395033&creativeASIN=B076NSFQ75&linkCode=df0&hvadid=198093834376&hvpos=1o3&hvnetw=g&hvrand=2952694566961028205&hvpone=&hvptwo=&hvqmt=&hvdev=m&hvdvcmdl=&hvlocint=&hvlocphy=9025430&hvtargid=pla-390387946052
A 1U shelf should do the trick. There should be able room for a cable modem + ER-X SFP on the below shelf. (Fits my USG / EdgeRouter Lite without a problem)
https://www.amazon.com/AC-Infinity-Cantilever-Universal-Heavy-Duty/dp/B01C9KYUG8/ref=sr_1_1?ie=UTF8&qid=1482159222&sr=8-1-spons&keywords=1u+shelf&psc=1
Note: If you're looking for an awesome faceplate, I've only seen 'em for the EdgeRouter Lite, not the ER-X SFP :(
Could always take a 1U Blank and a dremel? >_>
Also get some foam pads, they make a big, big difference. The low end will tighten up a lot. https://www.amazon.com/Auralex-Acoustics-Acoustic-Isolation-Charcoal/dp/B009EPP1EM?th=1
If you can, pick up a mic surround, it will make a huge difference in the source recording quality and allow you to "add back in" the right level of effect (levels, reverb). Like this: http://www.amazon.com/Microphone-Diffuser-Isolation-Absorber-Griffin/dp/B0082DAL3S but you can make one for like 1/10 that price with eggcrate foam.
Since they are unidirectional (cardioid) mics then I would suggest facing them away from each other as much as possible. That what they record less of the other person and more of your voice. Putting something in between you two to shield the sound from the other person's mic might help a bit as well. Possibly a mic shield like this one or this one (if you can get them in Canada).
The thought is to get as much of your sound into your mic and to shield as much of Lynn's voice from your mic as possible. Therefore I would put the mic shield close to your mic but directly facing away from Lynn and vice versa.
It could be a Behringer C1? But that giant bulbous black thing with blue on the inside is clearly some type of add-on that could probably be used with many mics.
... Which I think is trying to be a cheap version of one of these:
Pyle PSMRS08 Compact Microphone Isolation Shield, Studio Mic Sound Dampening Foam Reflector https://www.amazon.com/dp/B0117E33PG/ref=cm_sw_r_cp_apa_jPAYzbX204F48
Might just get one of these. https://www.amazon.com/NavePoint-Server-Cabinet-Locking-Lockable/dp/B009WS7TSW/ref=mp_s_a_1_1_sspa?keywords=2u+rack+drawer&qid=1572308746&sprefix=2u+&sr=8-1-spons&psc=1&spLa=ZW5jcnlwdGVkUXVhbGlmaWVyPUEzUjBITEc3TDU1WDI4JmVuY3J5cHRlZElkPUEwMDQxMDYyMVEzTVk2Q1BWVkpENCZlbmNyeXB0ZWRBZElkPUEwMTk4MjYzMjJPR1BOM1RKR0M4TCZ3aWRnZXROYW1lPXNwX3Bob25lX3NlYXJjaF9hdGYmYWN0aW9uPWNsaWNrUmVkaXJlY3QmZG9Ob3RMb2dDbGljaz10cnVl
Kill reverb. Get at least a microphone dampener if no other acoustification/isolation will be feasable. Electric guitars are easy if you're only recording audio in, percussion especially can be tricky with microphones in a non-treated room.
Read up on TweakHeadz, here are two good articles to read.
Two of these for $20. We have $1980 left.
One pair of Quad S-2 for $1000. We have $980 left.
One pair of Speaker Stands for $60. We have $920 left.
One Rythmik Subwoofer for $540. We have $380 left.
An integrated amplifier for $350. We have $30 left.
Some speaker cable for $8.50. We have $21.50 left.
A chair for $21.30. Congrats, you have 20 cents left.
Take this with a grain of salt, but I think so. I will be purchasing these soon. I can let you know how it works out. https://www.amazon.com/gp/product/B01GAMP2S6/ref=ox_sc_sfl_title_1?ie=UTF8&psc=1&smid=AZDBGW3MVFF0M
These are the ones I bought:
https://www.amazon.com/gp/product/B009EPP1EM/ref=oh_aui_detailpage_o04_s00?ie=UTF8&psc=1
> gik art panel acoustic
those look expensive, but really nice. Is there a cheap alternative if you don't care how the wall looks? Something like this: https://www.amazon.com/gp/product/B01GAMP2S6/ref=ox_sc_act_title_1?smid=AZDBGW3MVFF0M&psc=1 ?
I have three different kinds of shelves in there, all 2 post but rated for 40-60lbs
Printers: https://smile.amazon.com/gp/product/B00006HRKE/ref=oh_aui_detailpage_o02_s01?ie=UTF8&psc=1
UPS: https://smile.amazon.com/gp/product/B01C9L3K18/ref=oh_aui_detailpage_o02_s01?ie=UTF8&psc=1
Modem: https://smile.amazon.com/gp/product/B01C9KYUG8/ref=oh_aui_detailpage_o02_s01?ie=UTF8&psc=1
In case anyone finds this by Googling later, I experimented with two different generic rail kits, for science:
** I tried these first, and they DO NOT fit a Lenovo SA120 in a standard 19" square-hole rack. The design of these rails means they stick inwards about 1/4 centimeter beyond flush with the rail, making it an extremely tight squeeze for larger hardware like a (2U) SA120. While that alone might still be usable in some racks, additionally the depth of these rails is adjusted with some screws that have heads that stick yet another few millimeters inside, making it impossible to seat the machine. It might be possible to make the squeeze if you have a round hole or threaded rack, but I wouldn't chance it.
** These worked for me. They're a similar design to the NavePoint, but they leave a few precious extra millimeters between posts that made all the difference. It's still a tight squeeze, and I had to remove the SA120's rack ear protectors to make it fit (you can put them back on after), but it's in there good and securely, and flush with the rest of the equipment. Looks great.
Thanks to /u/Mthrboard for pointing me in the right direction, and to /u/donnydavis for offering to sell me a genuine kit!
If you're referring to the traps in the corners, they're actually not very high quality. I got them pretty cheap on Amazon. They're not bad for the price though.
The panels on the ceiling and side walls are from GIK Acoustics.
​
https://www.amazon.com/gp/product/B071XNPW6G/ref=ppx_yo_dt_b_asin_title_o03_s00?ie=UTF8&psc=1
​
https://www.gikacoustics.com/product/gik-acoustics-242-acoustic-panel/
Would some angled isolation pads like these be a decent alternative to stands/cinder blocks? https://smile.amazon.com/gp/product/B017UC162Q/ref=ox_sc_sfl_title_1?ie=UTF8&psc=1&smid=A3I4IYVZFDM8T
If you want to charge people use the studio yes.
Cheaper alternatives:
A sound isolation box
A closet filled with clothes. This works very well and is free
A smaller room. Larger rooms is where echos really start to be noticed.
Hang blankets around the room. Sometimes this is hard to do without nailing in to walls, but if you can figure it out, this will help too
https://www.amazon.com/gp/product/B01JNAXIII
These here. you gotta get some command strips or double sided tape of some kind to affix them to the wall though.
Looks good. I suggest wall mounting the TV to raise it up a little bit so you can put the center speaker below the TV on top of the TV stand. This would put the 3 front speakers at the same height.
Place the center speaker on a foam isolation pad, angled up towards the main seating position. A couple of these:
Monitor Isolator Pads Studio Monitor Speaker Isolation Foam https://www.amazon.com/dp/B017UC162Q/ref=cm_sw_r_cp_apa_4S0yybVD6BGBE
I suggest spreading out the front speakers a little more as well (6" more on each side) and angle them in slightly towards the main listening position.
I'd swap out those curtains and shades for light blocking ones as well.
There are some good movies on that 2nd shelf for demoing the setup, some of my favorites.
I ended up buying two packs of [these] (https://www.amazon.com/gp/aw/d/B00TP52HCK/ref=ya_aw_od_pi?ie=UTF8&psc=1) after my roommate started complaining about hearing me stream during the night. Covered my wall with these and now she says she can't hear anything when I stream.