Hammocks are the shiiiiiiiit. I swing in mine at night while I smoke and drink, and check out the sky, it makes life much more enjoyable.

If you can carve out a spot, you can get a set-up like that for 69 bucks on Amazon and those frames can hold a 6'3" 250+ frame + a couple of dogs with ease.

These carbon filters are used mostly in commercial spaces. In the United States they are commonly found in marijuana grow houses to move air outside. A carbon filter removes a high percentage of odors to reduce the risk of detection.

I like them in my home because I'm not a fan of buying other scented products that "mask" smells. When I walk into my home and my carbon filter is on it smells clean. I'm not sure if that clean smell is due to something from the carbon? Either way it's a clean, crisp smell that many people comment on and cannot be replicated by chemicals.

Cons: inline fans are loud and the system is a little bulky. Noise can be reduced by adding ducting to the end or buying insulated fans as referenced below.

Pros: I breath amazing air. You can cook/smoke inside your home and it's still going to smell amazing!

Filter: https://www.amazon.com/gp/aw/d/B008NYF8S4/ref=ya_aw_od_pi?ie=UTF8&psc=1

Quiet fan: https://www.amazon.com/gp/aw/d/B00EIRU2YU/ref=ya_aw_od_pi?ie=UTF8&psc=1

My hands would hurt so bad after a day of using those. I prefer bonsai trimmers like these. They’re cheap, you can trim just as tight, and they’re way easier on the hands.

Or..use spring loaded nippers.

Can I start off by saying that this well researched, well organized, informative post is a breath of fresh air compared to the "These balls mean its female, right?" and "Got clone, wat do guyz, lol" type posts, thank you for that.

I'd advise you skip the cheapo fan controllers and go with a Mercury 4 to maintain way tighter temp control. These controllers will raise and lower your fan speed to maintain a 10 degree swing. Or go full bore with the Arduino and control it with that.

A variac fan controller is also a good alternative to the cheap ones.

I'd also recommend a 6 inch setup as they're much more prevalent in home improvement stores. A six inch fan moving the same amount of air will also be quieter.

Consider Jack's hydro 321 if you're concerned you're paying a bit too much for Scott's brand bottled water... I mean GH nutes, sorry, I get confused sometimes.


I like these scissors.

https://smile.amazon.com/Sago-Brothers-Pruning-Scissors-Trimmer/dp/B00P0FK7W6/ref=pd_sim_86_23?_encoding=UTF8&psc=1&refRID=M6MNMDEB9656STMBFWVM

A 40x loupe will be hard to get pics with. People seem to have good luck with those phone attachment macro lenses.

You may need a temp controller for the seedling mat, but I've read of people using pencils under their seedling tray for a little air gap.

Game changing: https://www.amazon.com/Sago-Brothers-Pruning-Scissors-Trimmer/dp/B00P0FK7W6

Just bought another 24 pairs of these babies.

It looks like a thermal burn to me, if it's also scale rot, the care instructions would be the same. But if you are not regulating your heat sources, it's probably a burn.

Inkbird makes some affordable thermostats with a few extra safety features. I would start off by making sure every heat source (heating pads, lamps) are hooked up to one. If you have extra money and want a ton of safety features, go with something by Spyder Robotics - their Herpstat line is the best of the best and they are what I use. I know places like PetCo / etc don't say you need a thermostat, but they are absolutely a must-have. Even the most high end heat pads that swear they don't go over X degrees can and will fail and will get hot enough to burn a pet.

Make sure humidity is above 60% at all times. If you are using an enclosure with wire mesh top, cover most of it in saran wrap or foil, this should keep the humidity in. Even after your snake gets better, keep humidity at this level.

Switch to unprinted newspaper or undyed paper towels for substrate for now. Something easily cleanable and sterile. Change it often. Change water and wash bowl daily. Going for a sterile environment while she heals. If you haven't done a deep clean, get some F10 SC and do a deep clean of her enclosure and everything in it. This stuff looks SUPER SCARY, but it's ok! I put 1 ounce in an empty spray bottle and then fill the rest of the spray bottle with water, so it's super diluted. Once diluted, it can be sprayed on any of her decor and be left to dry and still be safe for her.

It goes without saying, but also follow any medication and care directions the vet gives!

Also - there's a lot of info in here that you might not have known before, and it's really understandable. There's a lot of incomplete, inaccurate, and out of date care sheets out there for ball pythons, and even after doing a ton of research, you still could have missed something. But you've figured it out now, and are taking appropriate steps to make her better which is a ton better than a lot of other pet owners. I hope your girl makes a full recovery and you have many more years with her. Please keep us updated!

I would either stop feeding (she probably wouldn't take it anyways) for now, or go down a prey size until she is better.

A battery does not have to be special built just for a CPAP, any battery that provides 12-volts DC will work (which is the same type of power your car battery provides). CPAP specific batteries are a scam. You just need to get the right DC power cord for your machine and hook it up to any 12-volt battery.

Now how many days will you need, and does your battery need to power anything else? Do you need it small enough to be legal to fly with (limit is 100wh (watt-hours) or 160wh depending on your airline).

The smallest and cheapest solution is the Easyacc Portable Power Bank 38000mah rated 144wh and costs $81. It is the size of medium paperback book and about 2lb. It has a built in cigarette outlet, usb ports, and a built in white light plus flashing red emergency light. Using my Dreamstation (without humidifier) it has enough power to give me approx 4.5 8-hour nights. Best of all, it's still under the 160wh limit the FAA has so it's legal to fly. It is also about 50% more capacity of a CPAP specific battery which are typically only 99wh.

Going larger you have the Renogy 222WH Laptop Power Bank or it's bigger brother the 266wh

If you need a built in inverter so you can get normal 120-v AC power (which will drain your battery quickly) something like the Jackery Portable Power Station Explorer 240, or Jackery Portable Power Station Explorer 500

There is also countless other chinese knockoff style power banks available. Most of them will be perfectly The only thing I would stay away from is anything that looks like this because they do not actually have a cigarette outlet (you have to get a barrel to cigarette adapter) and they tend to be actual garbage systems.

The gold standard for battery systems is the Goal Zero Yeti 400 Lithium Portable Power. I happen to also own this and it provides me with enough power for over 11 nights of power on my CPAP and still wasn't completely drained. It also comes in larger sizes. It is the most expensive option but the best designed. Weighs about 11lb, and can be charged pretty much from any solar panel big or small.

Other people will say the best thing to do is buy a lithium mobility scooter battery and build it yourself. Which I feel is only a good answer if you are handy wiring electronics. Some people just want a prebuilt answer.

TL;DR: see links below.

Beyond the actual science of which light is best, it really depends for many casual plant owners whether they want the light to look "decor friendly" or they want it to do a bang-up job of growing their plants. Honestly, there aren't many effective lights that look like they belong in a residence. No matter what anyone says, when it comes to grow lights, you do get what you pay for.

Below are 5 well-recommended options. I own all these (and others), having tried many entry-level grow lights. They're ordered by price, low to high, from $15 bulbs that go in ordinary lamps to an excellent entry-level grow light for about $175. The lower end work best as a supplement for natural light. The higher end will let you grow almost anything, even without a window.

Hope this helps you. Any questions, just ask. And yes, there are detailed, technical, scientific explanations for why these are better options than others; you can dive in there if you choose. Let's get to those 5 lights:

Miracle LED Almost Free Energy 100W Spectrum Grow Lite - Daylight White Full Spectrum LED Indoor Plant Growing Light Bulb for DIY Horticulture, Hydroponics, and Indoor Gardens Single Pack

ACKE LED Grow Light for Indoor Plants,Plant Light for Grow Light Stand,DIY Indoor Growing Light Panel for Germination,Seedling,Vegetative Growth and Flowering

Three Heads Grow Lamp, Bevice Full Spectrum LED Plant Light Auto ON&Off with 3/6/12H Timer and Memory Function, Light Intensity Adjustable, for House Plants Seedling Growing Blooming Fruiting

Roleadro LED Grow Light 1000W Full Spectrum 3500k Sunlike Plant Light Dual-Chip with ON/Off Switch and Daisy Chain for Indoor Plants for Seedling,Succulents,Growing,Blooming and Fruiting

Spider Farmer SF 1000 LED Grow Light,with Samsung Chips LM301B & Dimmable Mean Well Driver, Sunlike Full Spectrum 3000K 5000K 660nm 760nm IR for Indoor Plants Veg Flower

cy kick

and Diatomaceous earth.

a thermostat is a device that regulates the power of another device, such as a heat lamp, in order to control the temperature. a thermometer measures temperature, nothing else.

i'm seeing a ton of red flags here, so i'm going to post my BP info dump. the first three links are detailed care sheets, then a tub tutorial, and the rest are product recommendations. read everything thoroughly, come back with any questions. let me know if any of the links don't work.

glass tanks can be very challenging for ball python husbandry due to the high amount of air flow with the screen top and the total lack of insulation with the glass walls. it's generally recommended to use tubs or pvc reptile cages instead. wood enclosures can also be suitable if they're designed well and sealed properly to protect the wood against moisture. glass tanks can work, but they require a lot of modification and maintenance, which you'll find tips for in the second link. i'll give you product recommendations to cover options for tanks, tubs, and pvc/wood enclosures.

• the basics and then some
  
• common problems
  
• feeding problems
  
• here is a tutorial to give you an example of how to set up a tub. this is what i would recommend for an immediate setup, and you could upgrade to a pvc cage upgrade later. note: this tutorial shows adhesive velcro to attach the thermo/hygro to the tub wall, but you should not do that. tape and other sticky adhesives should never be used inside the enclosure, your snake can get stuck on it and suffer serious injuries. hot glue is the easiest reptile-safe adhesive option. screws or bolts can also be used to mount things on plastic/wood walls.
  
• pvc reptile cages are ideal. they have the husbandry benefits of a tub with the aesthetics/visibility of a tank, they're much lighter than wood or glass, and they will remain unaffected by decades of constant high humidity. animal plastics, boamaster, and boaphile plastics, are some popular companies. many people will use a tub for a young snake and upgrade to pvc later.
  
• spyder robotics makes high quality thermostats to regulate your heat sources with pulse/proportional temperature control and various safety features. this is a popular cheap thermostat with simple on/off style with zero safety features. inkbird thermostats are also low-cost but overall higher quality than the hydrofarm type. any heat source should be regulated by a thermostat to ensure safe and appropriate temperatures.
  
• heat tape or ultratherm heat pads are high quality and affordable under tank heater [UTH] options. this is a suitable heat source for most enclosure types. remember that a UTH will not provide ambient heat, it will only affect the temperature of the surface to which it is attached.
  
• a porcelain base lamp and ceramic heat emitter[CHE] is the best ambient heat source for a tank, and it will also work for some pvc/wood enclosures. any heat lamp that emits light, even red or blue, should not be used at night.
  
• a radiant heat panel [RHP] is the best ambient heat source in a pvc/wood enclosure. there are a few options, such as reptile basics and pro products.
  
• a digital dual sensor thermometer/hygrometer allows you to easily monitor the warm side floor temperature [with the probe] as well as the ambient temperature and humidity [with the main unit].
  
• an infrared thermometer allows you to spot-check surface temperatures anywhere in the enclosure.
  
• these hide boxes are a cheap simple hide with a design that offers the best sense of security for your snake. cave style hides, cardboard boxes, plastic food containers, etc, can also be used. half logs are not appropriate hides.

First of all, I don't agree that a generator is an important prep unless you have a specific life-or-death need, e.g. medical equipment or an electric-powered well. The average apartment-dweller should be able to get by without electrical service for a few days. Stock up on spare batteries for flashlights and such. Get some non-electronic forms of entertainment. Get a hand-crank radio — many of them can charge your phone as well. Get food that doesn't need refrigeration or cooking. Learn which food actually needs refrigeration for safety; don't throw out your whole fridge on day one of an outage.

That will cover the short term and, in a long-term disaster, fuel will be in short supply so a generator is of questionable use.

> Unfortunately, i live in an apartment in socal. Can generators even be used in an apartment? I have a small balcony.

Do not risk it. Carbon monoxide can get inside the building. Do not risk it.

As an alternative, consider a portable power pack, and remember to keep it charged up! Some can be charged from solar as well. Or DIY with a bare panel, a charge controller, a marine deep-cycle battery and an inverter. (Also, a lot of things such as LED light strips can run directly from the 12V battery and don't need an inverter.)

> How long do they last if i buy one and just throw it in storage?

All prepper equipment should be tested regularly. I'm not an expert but I would say run it for 30 minutes every month or two. Remember that gasoline goes bad after a few months. They also have starter batteries that need to be topped up like a car battery. You'll need to check the oil and air filter and replace if needed.

> Once i buy a house, what is the best generator to own?

Like any "what's best" question, it depends on your needs. How much power do you need? Look into a dual-fuel gas/propane generator as well. Propane is much safer to store and it stays good for decades assuming your tank doesn't leak.

Also for the love of god, don't jury-rig a connection to the house wiring. There are about seven ways to kill yourself or someone else by doing that. You need to use a proper transfer switch or at least a breaker interlock plate. The easier option is to rely on extension cords and not the house wiring.

You’ll need to buy grow lights. :))

I use these two though other growers might recommend better:

LED Grow Light Bulb, TaoTronics... https://www.amazon.com/dp/B0748D2SMB?ref=ppx_pop_mob_ap_share

Dimmable Spectrum Plant Grow... https://www.amazon.com/dp/B07DH47QZM?ref=ppx_pop_mob_ap_share

I bought this hammock from amazon and used it as my bed for a few months. At first, it was pretty cool having a hammock as a bed. After a few days I realized the stand wasn't suitable for sleeping in every night; I couldn't find a comfortable enough position to be able to have restful sleep.

I eventually bought a new hammock to see if it was the original hammock that was the issue. Well, this new hammock was even more uncomfortable when I mounted it on the stand I had. In fact, the stand that came with the first hammock wasn't compatible with the new hammock; I had to buy some tree straps so that the new hammock would sit right on the new stand.

It was really hard sleeping on my hammock setup; I was sad as I really wanted it to work for me. I'm sure if I created my own stand that actually worked for my height I would have had no problem sleeping. Eventually I bought a Tri Fold Mattress and a memory foam pad and just slept on that instead of the hammock; the Tri Fold + Memory foam combo is perfect! Best sleep of my life on that thing.

If you're going to buy a hammock to use as a bed, I would highly recommend making, or even buying, a hand-made stand that fits your height and weight.

I'm 6'0", ~154lbs

Also, If you're going to buy a hammock to sleep on I would highly recommend having a secondary sleeping station (possibly a pad of some sort) for those days where you just don't want to sleep on the hammock. Trust me, those days will come. I didn't think it would happen to me, but it did. If you have any other questions I'll gladly answer them! Unfortunately I can't give you information about wall hooks/mounting as I never went that route.

I posted this the other day but a Reddit user suggested I paint it black to have it absorb more heat so I figured I'd post up the finished product. If anyone is interested here's the materials I used, just cut the rubber hose attached to a new clean insecticide sprayer, attach adapter, put on your hose and boom, camp shower with fairly decent water pressure.

https://www.amazon.com/gp/aw/d/B002SAO7XQ/ref=yo_ii_img?ie=UTF8&psc=1

https://www.amazon.com/gp/aw/d/B001GZZFXA/ref=yo_ii_img?ie=UTF8&psc=1

https://www.amazon.com/gp/aw/d/B0039EEN0M/ref=yo_ii_img?ie=UTF8&psc=1

Not at all! Here's the link!
https://www.amazon.com/dp/B07LG39B3M?ref=ppx_pop_mob_ap_share

A 3-way soil tester will help as well because although lime will help break down the clay, adding too much base will throw off pH balance and impede microbial growth. They're pretty cheap, as seen here: https://www.amazon.com/Sonkir-Soil-Moisture-Tester-Gardening/dp/B07BR52P26

Anyone tried these? I’m looking for something in this price range

I have 3 sets of these guys (so 6 total lights) - https://www.amazon.com/gp/aw/d/B07LG39B3M?psc=1&ref=ppx_pop_mob_b_asin_title

They are hooked up to a $10 smart timer that's programmed to cycle the lights, 4 hours on and 10 minutes off (recommended by the manufacturer).

I've had them for 3 months and have observed decent growth and farina coloring.

For about $200 you can be charging laptops and cell phones and running some fans and lights in your house. Here's the breakdown:
Solar Panel - $106
Charge Controller - $38
Inverter - $20
Battery - Anything 12 volt, ideally "Deep Cycle" but a car battery will work if you have one. This can be between $30 and a lot, depending on what you want to run.

The parts aren't special, they were just the cheapest I could find on amazon, and while they took a little longer than I wanted to get there, they did get delivered to San Juan. Now my family is charging and running all kinds of things off the sun while the idiots in government continue to suck at their jobs.

Yup, I second that for roaches. I haven't used it personally but I've heard a lot of folks talk about it. After using the gel bait, I'd also suggest this. Grab a one gallon sprayer from Lowe's or Home Depot and you're set. I use the one ounce per gallon of water mixture and spray the outside of my house every couple of months. Shout out to /u/bagodees for suggesting both in a similar thread.

here you go:
https://www.amazon.com/Apollo-Horticulture-GLK600LS24-Digital-Dimmable/dp/B005ECZQTY/ref=sr_1_6?ie=UTF8&qid=1510944022&sr=8-6&keywords=HPS+600w&dpID=51oUcNAloTL&preST=_SY300_QL70_&dpSrc=srch

First grow.

This took 2-3 months. Seems like I ran into a number of first-timer pitfalls along the way. Good learning experience though.

Can't wait. So god damn tired of shady, undependable hook ups.


Edit 2:

Photos of my setup.

• http://i.imgur.com/fc8wn1B.jpg
  
• http://i.imgur.com/HmUWGgR.jpg
  
• http://i.imgur.com/nOcwlPm.png
  
  
  
  Edit 1:
  
  Some have asked about my setup. This is about everything. This is my first grow so take my suggestions with a cup of salt but this stuff has worked well for me.
  
  Tent:
  
  Zero complains. Very happy with this. It just fits perfectly into a closet (had to remove the hanger bar though).
  http://www.amazon.com/gp/product/B004U6WCMY
  
  
  Air
  
  
  
  Carbon filter:
  
  The inside of my tent stinks. I smell absolutely nothing outside. Don't get caught. Get a good carbon filter. Maybe not this one, but something.
  http://www.amazon.com/gp/product/B004FVJK60
  
  
  Inline fan:
  
  I hand this outside the tent. No need to take up any space or add any heat inside the tent.
  http://www.amazon.com/gp/product/B002JQ14F8
  
  
  Variable xformer for fan control:
  
  This allows me to control the noise and airflow. Every other fan controller made the fan buzz. This thing is quality built. I keep it around 50v.
  http://www.amazon.com/gp/product/B006NGI8VS
  
  
  Circulation fans:
  
  http://www.amazon.com/gp/product/B004RTMD8C
  
  
  DWC
  
  
  
  
  Bucket top net pots:
  
  http://www.amazon.com/gp/product/B0049XIIGC
  
  
  Air pump:
  
  http://www.amazon.com/gp/product/B002JPEVMC
  
  
  Airline:
  
  The black just prevents light from getting into my res.
  http://www.amazon.com/gp/product/B001D4XTUU
  
  
  Air stones:
  
  http://www.amazon.com/gp/product/B0050HJ7Q6
  
  
  Check valves:
  
  You NEED these. Many airlines are thin enough that if the power goes out or a hose becomes disconnected, capillary action might permit water to back-flow into your electrical air pump and/or just flood your room. Don't take chances when a .50 cent valve will protect you. There are some horror stories in the aquarium hobby about this. Note, even if the air pump is higher than your res, capillary action can pull the water up through the air hose. This is the same principle that allows 100ft trees carry water from the roots to the canopy.
  http://www.amazon.com/gp/product/B00977J508
  
  
  Lighting
  
  
  
  Lights:
  
  Word of warning. Start off a good distance between the lights and your canopy. These product more light than you think and I have burned and cooked plants from keeping these too close. They don't product a ton of heat or anything. I think it's just too much light if they aren't a good foot or so away from the canopy. I assumed I could practically lay LEDs on top of my canopy. Not so.
  http://www.amazon.com/gp/product/B00FGFLCXS
  
  
  Adjustable ropes for lights:
  
  Chains work, these are just faster/easier to adjust.
  http://www.amazon.com/gp/product/B0098R0600
  
  
  Tools
  
  
  
  Temp/humidity sensors:
  
  http://www.amazon.com/gp/product/B0013BKDO8
  
  
  pH pen:
  
  I used to do chemical reagent tests (I have tons of aquariums so I had it laying around). Never again. A pen is fucking awesome for dialing in pH every morning. Get one!
  http://www.amazon.com/gp/product/B00EQISYQO
  
  
  Pruning snips:
  
  These are great. Sharp as fuck and solid.
  http://www.amazon.com/gp/product/B00004SD76
  
  
  Training wire:
  
  What I use for my scrog screen and early training before the screen goes in. Also good for random shit that's temporary enough I don't want to waste a zip tie.
  http://www.amazon.com/gp/product/B001EXJ652
  
  
  Nutes/Water changes
  
  
  
  
  Pond pump:
  
  This is another must have! I've been using these for a while now to handle water changes in my aquariums. It's also awesome for mixing nutes before they go into your DWC. I drop one in a bucket without a hose attached and then just dump all my nutes and such in. The pump does all the mixing. Then I adjust the pH a little. Give the pump about 10-20 seconds to mix my pH up or down in and test again. I don't have to worry my pH adjustment isn't probably mixed yet. I makes the mixing process so easy and fast. I also use these to pump out my res once the scrog screen is in place.
  http://www.amazon.com/gp/product/B006M6MSL0
  
  
  Root protectant:
  
  One of my early problems was with brown algae. This cleared it right up after a week.
  http://www.amazon.com/gp/product/B00IGFH3FG
  
  
  Syringes:
  
  No guess work. I know exactly how many ml I'm adding.
  http://www.amazon.com/gp/product/B000RB3CV6
  
  
  Cal-mag:
  
  http://www.amazon.com/gp/product/B000J2CUPW
  
  pH control:
  
  http://www.amazon.com/gp/product/B000BNKWZY
  
  
  Nutes:
  
  http://www.amazon.com/gp/product/B000COBT54
  
  http://www.amazon.com/gp/product/B000CO7U02
  
  
  
  
  

Any type of foaming ability included with a pressure washer will be crap. You need to buy an actual foam cannon such as this one to get the results you want. There are cheaper options than this one but I elect to stay with MTM.

I usually put 2 ounces of soap into the canister to get optimal foam.

Make sure you feed her some calcium/magnesium if you're growing in coco. Have fun!

I usually only grow 2 or 3 plants at a time so I'm probably not as particular about what I use to trim as others who end up spending days doing it. I am happy to use bonsai trimmers such as this

https://www.amazon.com/Sago-Brothers-Bonsai-Pruning-Scissors/dp/B00P0FK7W6/ref=sr_1_14?ie=UTF8&qid=1542645012&sr=8-14&keywords=trimming+shears

good effort, but don't get that one, get this one. it's cheaper, by the same company, and the probe is designed for aquariums:


https://www.amazon.com/Inkbird-Temperature-Controller-Thermostat-100-240V/dp/B015FKG4CC/ref=sr_1_3?keywords=Inkbird+Digital+Temperature+Controller+Thermostat&qid=1554760604&s=lawn-garden&sr=1-3-catcorr

Have you thought about getting a 2x2 tent? Running with a HLG 100 it should be very manageable and around 250-300 for the setup, mostly from amazon.

You could probably squeeze 2 plants in there although 1 would be more comfortable.

Fabric pots would help with root circling/small pots.

One thing to keep in mind is that smaller pots will need watering more often.

Topping, LST and scrogging would help keep the plant short.

There aren't any battery chemistries that run at 5V +/- 10%.

It sounds like you should get a 12V deep cycle lead-acid battery. They are very common, cheap, can take heat, have solar chargers available, and come in the capacity you need.

All you need is a 12V > 5V regulator, which is also very common, cheap, and available.

edit: This one has a 5V regulator built in, so you could run it straight off the USB ports if your load is < 3A

Nice... The controller you posted is unavailable, but a newer version is offered on Amazon.

It's a great ritual that I do when the weather is warm and they are out. Go on Amazon and get the 12" tweezers if you want to capture them for the thunderdome. No matter what, don't pay the ridiculous costs of 'Scorpion Proofing' your home. It doesn't work any better than owning cats and using Cy-Kick pest spray monthly on your baseboards and doorways (http://www.amazon.com/Cy-Kick-Controlled-Release-Cyfluthrin-Insecticide/dp/B002ACMKV8). BTW, I heard chickens are the best at catching & eating scorpions.

I had this question for another grower. They said they used a 2 gallon Chapin Sprayer

https://www.amazon.com/Apollo-Horticulture-Adjustable-Improved-Internal/dp/B0098R0600/.
https://www.amazon.com/s/ref=nb_sb_noss?url=search-alias%3Dlawngarden&field-keywords=Reflector+yoyo&rh=n%3A2972638011%2Ck%3AReflector+yoyo

I had the same concern at first. These came with my light (MarsHydro 900w LED), but probably a cheaper knock off version. Worked great! I always held the beams the light hangers were secured to when i moved the lights up higher as they tended to flex. Since i was very paranoid i used paracord secured to the top side tent beams in case the light fell when i wasn't home. i can happily say i didn't need to do that since the light never fell, but small price to pay for peace of mind though. Hope that helps!

This is my set up and works great. The reviews say the MTM doesn't work with the SunJoe SPX3000 but it does. I've ordered 3 in total for friends and myself. All of them has came with the 1/4in fitting and works perfect with the SPX3000. So the idiots that left the reviews saying it does not work must not know how to change out the fittings or something?
Sun Joe SPX3000 Pressure Joe 2030 PSI 1.76 GPM 14.5-Amp Electric Pressure Washer https://www.amazon.com/dp/B00CPGMUXW/ref=cm_sw_r_other_apa_-TMtzb9F0DSFK

MTM Hydro Professional Adjustable Foam Cannon with Bayonet, 2600 PSI https://www.amazon.com/dp/B00EDSLVQC/ref=cm_sw_r_other_apa_BVMtzbW630TGF

I've only owned a single foam cannon and that's the MTM Hydro Professional. This one has a smaller orifice specifically meant to be used with electric pressure washers that don't output the same water as gas pressure washers.

When I was researching foam cannons, I noticed the community was split on cheap <$20 foam cannons (the ones that pop up on Amazon by searching for "foam cannon"), and by higher end >$50 foam cannons like the MTM I have.

A lot of people were saying the cheaper ones performed just as well as the expensive ones, and a lot of people said they didn't. One thing I knew for sure from watching take-apart videos, was that the internal construction for more expensive foam cannons was a lot better than the cheaper ones. I figured if I was going to be using this in a business setting, I should opt for the more expensive one ensuring I get the better quality.

No pictures being as I am at work but:

• Morakniv
  
• Hori-Hori for digging roots
  
• Bonsai Pruning Scissors
  
• PU Coated gloves (for picking nettles and such)

As a vague generality, if you take a plant and put it under a light and give it water, it will grow, and with enough time, will produce -something-. Obviously, you think it takes a bit more, so that's why you're here. When it comes to indoor growing, there are many things that have to be taken into consideration because we are first removing all of the things a plant requires for survival then take it upon ourselves to be the one to provide it. To make these things apparent, we need to account for all of the things deprived to the plant by removing it from the outdoors:

• Light
  
• Humidity
  
• Air Flow
  
• Temperature (100% dependent on what plant you're growing)
  
  
  The Law of the Minimum states that a natural system is only as strong as it's weakest input. The number of factors that can limit a plant's health are near limitless, but these above items need to be addressed to begin encroaching on the realm of 'happy, healthy plant'. The information below will be debated by some, but here's my stance: Growing indoors is an energy intensive activity, and the costs can get out of control quickly. My philosophy is that I want the biggest possible return on my investment of money, time, and energy, so I aim to produce the best possible product. Ambient airflow, air pressure, and humidity affect all aspects of growing; changing one, changes the other. For example, setting up a exhaust in the tent that can move air out at a rate higher than it flows in causes something referred to as a Vapor Pressure Deficit, in which the pressure of the air literally sucks moisture out of the air and restricts the plants natural "respiration" process, resulting in upward curled leaves on plants, and stunted growth (this is fixed by using a fan speed controller and using an appropriately sized fan for the space). You want all the air inside of a tent replaced every 5 minutes in order to cause no interference, but a plant can usually take significantly more pressure before showing signs of stress. Like temperature, this factor is unique to each type of plant, so YMMV. If you're not going for smell control however, a minimal amount of air flow will suffice. The less interference you have to introduce to a grow tent, the less variables that have to be accounted for. Generally, you want your humidity around 70% for leafy greens and herbs, and 40-50% for anything that bears vegetables or fruit. This isn't a panacea, but in your case it gets you to 'close enough' with the least consequences. Adding degrees of varying control will give you the ability to adjust your environment accordingly to meet these unique requirements.
  
  
  There are many, many ways to measure light, and it can be as simple or as complicated an ordeal as you like. I like to break it down and compare the earth to the sun like we compare a grow tent's square footage to wattage of the grow light. That said, the sun produces 3.86 x 1026 watts of energy, or 380,000,000,000,000,000,000,000,000 watts. Most of that energy goes off into space, but about 1.74 x 1017 watts strikes the earth. (ie: 174,000,000,000,000,000, or 174 quadrillion watts). Broken down to the 197 million square feet that makes up the surface of the planet, approximately 100-130 watts of sunlight are needed per square foot of growing space in order to create an environment suitably similar to sunlight. In your environment, you need approximately 1,000 watts of light in order to get the same kind of results you'd see with old fashioned direct sunlight. It should be noted however that you can just as well get away with weaker lights (I use 600 watts in the same footprint dimmed to 450W with no major problems, and recommend the same here to avoid ventilation complications).
  
  
  Now, what kind of light do you need? pre-tl;dr If you're operating on a tight budget, get an array of T5s and call it good. You can get away with just about anything, although anything in the 5500k spectrum for a T5, CFL or HID light will be perfectly suitable. For LED lights, don't trust the advertised wattage, and look at the actual wattage rating of the product to get a good ballpark estimate of what kind of experience you can expect with any given light (while manufacturers can fudge light spectrums on LEDs, they can't fudge true watts). Some lights have more abstract advantages over others (e.g. par levels, spectrum ranges, etc), but for simplicity's sake we'll not worry about those.
  
  
  CFL lights are far and away one of the cheapest ways to get into indoor growing, and the lights produce very little heat, minimizing needs for ventilation. An added benefit of being a cool light is that plants can be extremely close to CFL bulbs without blanching the leaves, enablng a grower to create grow spaces in extremely confined areas. The downside is clutter and the requirement to construct a hood: You would need 20 50 watt CFL bulbs to match a single 1,000 watt HID bulb, and 20-bulb hoods that fit in a 2x4 footprint don't exist so far as I know). Plants grown on fluorescent lights tend to experience less dense growth than HID when grown using equivalent amounts of light wattage per square foot. Fluorescent lights are good for around 10,000 hours of use in growing. You can expect to pay around $75-$125 for a CFL array, and around 12 hours constructing the array itself.
  
  
  T5 lights have all of the advantages of CFL, and fewer disadvantages (less clutter, no need to build a hood) at the exchange of increased cost (a bit higher than HID for the really nice arrays). You can expect to pay around $175 for a T5 fixture. T5 and CFL lights can be kept around 10-12" from plants.
  
  
  HID lights are the industry standard, forming a balance between cost, output, and required infrastructure to support. The cost is comparable to T5 lights, but come with a number of distinct advantages. Science aside, an HID will produce denser, fuller plants through all stages of growth using the same wattage of T5s and CFLs and are produced with a significantly lower failure rate than many LED units. HIDs produce a LOT of residual heat, but this problem has long been accounted for with the advent of ventilated hoods. These hoods are designed to perfectly mate with HVAC components, allowing for cold air to be blown directly over the hot bulb, and none of that residual heat ever making it's way into the tent. HID lights are kept 12-16" from the plants
  
  
  LED lights are the new kids in the block. Beginning with the trendy magenta glow, LED lights were designed to utilize specific spectrums of visible light and eliminate spectrums deemed 'harmful to plants'. We now know that to be farce, and nearly all of the highest end LED arrays are full spectrum COB (chip on board) arrays that can go into the thousands of dollars in price (or about the same as a T5 array, if you're savvy enough to build one yourself). There are a number of magenta lights that still exist, and they can be utilized to great effect (I've done a number of grows through flower on a Mars Hydro II light), however this information comes with a disclaimer: Many LED light manufacturers lie, and many LED light fixtures fail. While many manufacturers will list data sheets and cite numbers til they're red in the face, most LED lights are manufactured in China, and many more fail to meet the quality control standards of the original design. If you want a good comparison, consider the 'hoverboard' fiasco last Christmas, with thousands of knockoff boards catching fire across the world. Speaking of fire, the latest and most powerful LEDs produce a LOT of waste heat, enough so that a large part of many arrays include a number of heatsinks and fans to keep them cool. This bothers me, because instead of being able to pipe hot air away from the tent in a nice, single direction, the LED light is piping out hot air in every direction. I generally find my tents run around 10 degrees (fahrenheit) hotter when I run LED lights than HID. LED lights are kept 18-24" from the plants.
  
  
  Assuming a non-defective unit, LED lights have an expected lifespan of 30,000-50,000 hours. A single LED light is worth the price of 3 HID bulbs. LED Lights offer even higher PAR levels than HID (often described a bit inaccurately by some as 'light penetration'), creating compact, bushier plants than HID lights using an equivalent wattage. LED makes sense if you're investing in this hobby for the long term, and want the most out of your money.
  
  
  All of the above taken into account, and with your space, I recommend a 4 foot 450w T5 light, or 600W HPS HID light with a dimmable ballast and cool hood, dialed down to 450w to increase bulb lifespan.

I was wondering what the catch was. I was trying to find the product history.

OP, it's a Chinese special with razor thin margins (they have a different ballast in the photo). You can see on their webpage that the ballast is even different than the one shown on the Amazon link.

I'd go with this more efficient reflector if you do decide on this brand. The cool tube is a relatively inefficient reflector.

Looks like the seller has inconsistent pricing. edit: the seller buys for half this price

Same ballast, different label. Typical of Chinese imports.

That shipping price makes it too good to be true.

Ordered Via Amazon.

Overall, 3/5 stars. The hood weld seams, spot welds, are garbage and falling apart. Both inlets for the hood are bent and will need fixing. It will function and do it's job, but the package protection for shipping was underwhelming. Shipped by Psychedelic FrogFish Co in Walnut, CA.

I have a 4'x4' Aviditi tent, fan + filter combo, and some other stuff coming up for my next review. I will post pictures once it is all setup.

EDIT: Contacted the seller and he is shipping a new hood, free of charge, and didn't request the old hood back. He is legit.

I used a 6" filter that worked nice for me, I'm sure they have a 4" version

https://www.amazon.com/gp/product/B008NYF8S4/ref=oh_aui_search_detailpage?ie=UTF8&psc=1

I use this style scissors for my fine trimming. I bought two pairs for a buck on wish.

Sago Brothers Bonsai Scissors, Pruning Shears for Bud and Leaves Trimmer 5 PCS https://www.amazon.com/dp/B00P0FK7W6/ref=cm_sw_r_cp_apa_DeANBbJVTGJQ5

A full spectrum LED light is going to be your best balance of light quality, low heat, and light that doesn't look crazy weird.

LED Grow Light Bulb, TaoTronics Full Spectrum Grow Lights for Indoor Plants, Grow Lamp, Plant Lights for Hydroponics, Organic Soil ( 36W, All Wavelengths, FREE E26 Socket) https://www.amazon.com/dp/B0748D2SMB/ref=cm_sw_r_cp_apa_LYQYAb1WEX1PK

With that said, one of these will be enough to nurture a juvenile plant along, but a mature plant will be straining for a little more then just one bulb can offer. This type of bulb should be used within a couple of inches of the foliage in a perfect world.

You want the best?

you got em

Grows my weed and succulents

the left one

the right one

As you can see, the left one is more yellow while the right one is more white. I was torn between the two and didn’t know which one would be better for the plants so I kept them both 😂

These "solar generators" or whatever you want to call them are coming down in price. They are not enough to run major appliances but it can give people an option to run lights and charge phones if you cant run a generator. Can recharge them during the day with a solar panel so its good to go again at night.

I just finished building something similar that can run 2 cpap machines for a night, was kind of looking forward to testing it today if the power goes out. So far no outage in Dartmouth.

Not OP, but I just bought this one and I'm pretty happy with it.

This is the grow light (it’s alright not the best) and those are my baby rosettes in front, I’m actually not sure what either are honestly

The more you spend, the better the light. The better the light, the better the plant. The better the plant, the more you yield. The more you yield, the more cost effective the operation is.

Cheapest option. Buy two:

https://www.amazon.com/ACKE-Germination-Seedling-Vegetative-Flowering/dp/B07GGX3R9T

Slightly better:

https://www.amazon.com/Lenofocus-Spectrum-Hydroponic-Vegetable-Flowering/dp/B07TV9GWPB

Best option within your price range:

https://www.amazon.com/Horticulture-Lighting-Group-High-Efficiency-Upgraded/dp/B076QDKVDZ

Linked

This is the one my mom uses, bendy but gets hot so make sure it's away from hazards!

This is the one I use! I have two currently.

That model is likely overkill to charge ~50%...sounds like you really only need a small top up (20% or so) to get you back home under power:

This one would almost certainly get you what you need to get home under power:

https://www.amazon.com/Portable-Jackery-PowerBar-Universal-Compatible/dp/B07F119R6P/ref=sr_1_13?keywords=portable+laptop+ac+battery+charger&qid=1571105532&sr=8-13

I suspect this would get you 15-20% increase in charge over what you pulled in from your commute with.

if you wanted to go with one of the hefty jackery ones, this one would likely get you 60% from 0 or more charge into the battery of the rev (67k mah):

https://www.amazon.com/Jackery-Portable-Power-Station-Generator/dp/B07D29QNMJ/ref=pd_bxgy_86_img_3/136-2471141-6721145?_encoding=UTF8&pd_rd_i=B07D29QNMJ&pd_rd_r=5a05793c-d5db-4525-bb61-cb980e68e1a8&pd_rd_w=zT417&pd_rd_wg=jYB1X&pf_rd_p=09627863-9889-4290-b90a-5e9f86682449&pf_rd_r=3XT0KTAE3RDV0FDAV2RY&psc=1&refRID=3XT0KTAE3RDV0FDAV2RY

no need to spend 425 USD.

PS: this one is crazy cheap and would likely charge you to at least 60% from 0 (great reviews to boot) - at 64.8k mah slightly less mah than Jackery hefty one, but nearly identical spec wise, and much cheaper:

https://www.amazon.com/Rockpals-250-Watt-Generator-Rechargeable-Emergency/dp/B075SSMR6K/ref=pd_cp_86_4/136-2471141-6721145?_encoding=UTF8&pd_rd_i=B075SSMR6K&pd_rd_r=44eeb9b7-24bb-43b9-8c6a-26adef14b6cb&pd_rd_w=YNe82&pd_rd_wg=nhtvD&pf_rd_p=0e5324e1-c848-4872-bbd5-5be6baedf80e&pf_rd_r=WCZPCS731EJZM70705MS&psc=1&refRID=WCZPCS731EJZM70705MS

I may even give that a go for the price!

Source: I own this one and it charges my rev from 50% to about 95% (42k mah, while the two bigger guys above are around ~65k mah):

https://www.amazon.com/Portable-Outlet-Battery-Pack-ChargeTech/dp/B06Y3NF7N2/ref=sr_1_1?keywords=chargetech+42000&qid=1571106042&s=electronics&sr=1-1

I can't recommend the one that I own...had some issues with it.

You’re not going to find an affordable battery, and certainly nothing that you can support with Velcro, that can run that stuff.

There are “battery generators” that are designed for tailgating and camping but they’re not small, and the ones that are, aren’t that powerful.

Here’s an example; it has a max 200W output. My little Krups coffee grinder pulls 110W according to the label. I’d guess a juicer to be more like 500.

Jackery Portable Power Station Explorer 240, 240Wh Emergency Backup Lithium Battery, 110V/200W Pure Sinewave AC Outlet, Solar Generator for Outdoors Camping Travel Fishing Hunting https://www.amazon.com/dp/B07D29QNMJ/

I think it would make your life worse, not better, to have to charge your kitchen every night.

https://www.amazon.com/gp/product/B000BPFYG4/ref=pd_sim_86_6?ie=UTF8&pd_rd_i=B000BPFYG4&pd_rd_r=TX6NDP511EN0B22G0TNZ&pd_rd_w=TjCWM&pd_rd_wg=Ojn0F&psc=1&refRID=TX6NDP511EN0B22G0TNZ

https://images-na.ssl-images-amazon.com/images/G/01/outdoor-living/detailpages/claber/claber-koala-howtouse-sm.jpg

Depending on the shape of your spout, you can use something like this: https://www.amazon.com/gp/aw/d/B000BPFYG4/ref=mp_s_a_1_7?ie=UTF8&qid=1487694645&sr=8-7&pi=AC_SX236_SY340_FMwebp_QL65&keywords=sink+to+garden+hose+adapter

Or, get a small submersible pump and a decent sized cooler and run a loop.

This http://www.amazon.com/Cy-Kick-Controlled-Release-Cyfluthrin-Insecticide/dp/B002ACMKV8/ref=sr_1_1?ie=UTF8&qid=1397533022&sr=8-1&keywords=ck+kick and this http://www.amazon.com/GGI-Ultraviolet-flashlight-Blacklight-CREE395/dp/B0091G48CK/ref=sr_1_12?ie=UTF8&qid=1397532979&sr=8-12&keywords=blacklight+flashlights are your two new best friends. Kill them at night. Read up on scorpion hunting

You can't buy the "good" stuff at Home Depot. You either wanna hit up a Bug & Weed Mart type place in town, or just do what I did and order from Amazon.

One of those Cy-Kick bottles lasts me like 8 sprayings on a 3k sq ft house. Well worth the $40.

Edit: also -- if you buy Cyfluthrin, you won't need anything else. It kills everything under the sun.

Cy-kick works for me. I had a pest control company come out a few times and it was something they used. Concentrated to mix a few gallons or an aerosol can for cracks etc.
http://www.amazon.com/gp/aw/d/B002ACMKV8?pc_redir=1406538207&robot_redir=1

Kind of depends on if it's hot or not (Antibalas last year was real toasty), but if you bring one of these filled with water for your group and people around you that want it, it's always a hit.

https://www.amazon.com/Chapin-20002-Fertilizer-Herbicides-Pesticides/dp/B0039EEN0M/

I wet it down using a garden sprayer like This and a 6" drywall knife

That's what I do, even with access to a hose, because it's too cold to use the hose about half the year. Get some Optimum no-rinse, and a garden sprayer and use in conjunction with a two-bucket wash or just one bucket and ton of microfiber towels. There's no foam, but it has the same effect.

Grab one of these sprayers off amazon.

https://www.amazon.com/gp/product/B0039EEN0M/ref=ppx_yo_dt_b_search_asin_title?ie=UTF8&psc=1

and a gallon of the goods

https://www.amazon.com/gp/product/B00ARKS3XO/ref=ppx_yo_dt_b_search_asin_title?ie=UTF8&psc=1

A splash of the goods and fill the rest up with water and away you go.

I have a ton of cracks and I spray every couple months. I kind of like doing it too.

https://www.amazon.ca/gp/product/B0039EEN0M/ref=ppx_yo_dt_b_asin_title_o04_s00?ie=UTF8&psc=1

This thing has saved me. I fill it up, set a chair next to the tent, pump a few times, throw on some tunes and water away. Might take a bit longer, but I find it saves my back pain !

I'm currently using the Ryobi 1,600-PSI 1.2-GPM Electric Pressure Washer. It comes with three swappable nozzles and also fits my MTM Hydro Original Professional Foam Lance.

4 different ones.
lights


https://www.amazon.com/gp/product/B07C59J8L2

https://www.amazon.com/gp/product/B01IVQ96WW

https://www.amazon.com/gp/product/B01IVQ96MW

https://www.amazon.com/gp/product/B015FLSOCE


fans


https://www.amazon.com/gp/product/B07D8ZC566

https://www.amazon.com/gp/product/B00I8Q30SC

clip fan


other stuffs


Frog soil

Smart pots - half 3 gallon half 5 gallon

Advanced nutrients nutrients

hygrometer: https://www.amazon.com/SensorPush-Wireless-Thermometer-Hygrometer-Android/dp/B01AEQ9X9I/

6 inch intake fan from home depot

filter: https://www.amazon.com/gp/product/B008NYF8S4

filter fan: https://www.amazon.com/gp/product/B01CTM0JF2



strains


1 white widow

1 amnesia haze

2 money bush

2 jack herrer

Start small. It'll save you money, let you get your feet wet, and help you learn how to grow better, and then you can buy bigger.

My "starter package" is:

• A 2' x 2' x 3' grow tent - $55.
  https://www.amazon.com/gp/product/B00SWGYYWO
  
  
• A grow light ($90). I prefer COB's as they're easier to fix than blurples.
  https://www.amazon.com/gp/product/B01I4NY8KW
  
  
• A power strip zip-tied to a pole in the tent. Makes wiring prettier and easier. ($24) I chose a nice metal one, but you can use a cheaper one.
  https://www.amazon.com/gp/product/B00F8ZQYHA
  
  
• Hangers to hold the light ($8)
  https://www.amazon.com/gp/product/B0098R0600
  
  
• A fan and filter ($70), and variac ($90) to filter smell and move air to keep things cool. This combo is overkill for this tent, but I ended up using it on later tents so it's a good long-term investment. You can cobble something cheaper together with some work, but this "just works" out of the box.
  https://www.amazon.com/gp/product/B004Q2ER5C/
  https://www.amazon.com/gp/product/B006NGI8VS
  
  
• 5 gallon Smart Pot ($7) for growing, FoxFarm Ocean Forest Soil ($16.50), Plant saucer ($7) for growing. You can save some money here by shopping around. In particular, Amazon's price for FFOF is about double what I pay at the (very expensive) local "indoor gardening" center.
  https://www.amazon.com/Smart-Pots-5-Gallon-Soft-Sided-Container/dp/B002JUOWB2
  https://www.amazon.com/FoxFarm-FX14053-12-Quart-Organic-Potting/dp/B001I49Q98
  https://www.lowes.com/pd/Garden-Treasures-15-31-in-Rust-Plastic-Plant-Saucer/50445000
  
  
• Go Box Plant Nutrients. This should last you several grows.
  https://www.amazon.com/gp/product/B004PS4B08
  
  
• Seed of your choice (let's say $10).
  
  So for about $420 (heh), you can get your foot in the door and start growing. This is a nice setup too, you can probably save $100 by shopping around, buying used, or doing-it-yourself. I've left off a few odds and ends like dryer duct, Fiskers for trimming, weed fabric pins for low-stress training, pitcher for watering, Mason jars for storage, but you can likely find those or suitable replacements around the house without spending money.
  
  I also have a Raspberry Pi 3 ($43) with Sense Hat ($37) and metal case ($15) in each of my grow tents to log temperature/humidity and other things. I'm interested in eventually using the GPIO functionality to water my plants too. Not critical, but definitely a nice thing to have, especially if you're the hacker type. If you go this route, you might look at raspiviv.com too.
  https://www.amazon.com/gp/product/B01C6FFNY4
  https://www.amazon.com/gp/product/B014HDG74S
  https://www.amazon.com/gp/product/B0722L338Q
  
  I'm glad I bought a good intro setup because I still use it now that I've upgraded. I now have a 3' x 3' GG Shorty tent with HLG 300 LED for flower, a 2' x 2.5' GG Shorty tent with two 400W Roleadro COB's for veg, and my "intro package" is now my germination/cloning tent (and drying tent too since several people suggested that too). Being able to have three tents (germination -> veg -> flower) working simultaneously is increasing my output quite sharply. I'm doing this to help a relative with cancer, so you may not need to go quite as crazy as I did.
  
  You mentioned using 35+ gs (~1.25 oz) a month. You probably aren't going to be able to grow that much given the constraints of tent size and light wattage (plus being a first-time grower! You'll learn a lot!). So once you get used to it, you'll probably want to buy more stuff. Marijuana isn't addictive, but growing marijuana absolutely is.
  
  Once you've got your hardware, the variable cost is seed (~$10), soil (~$5), nutrients (~$20), and electricity (~$30). From that, I'm going to estimate you can grow ~1.5 ozs (you can do more as you learn more though). So you're looking at ~$40/oz after you've made the initial hardware investment.
  
  Hope this helps. Depression, cancer, and everything else can just go suck it.

My light also came with the same kind of diagram, I have it about 12" away at 1070 "PAR" and everyone has very good stress coloring and are loving it. I wouldn't set up the light to be at that distance right away, however, since they won't be used to the light, I started out about 2 feet away and moved it closer every few days to get them used to it. I got these little rope hangers so it's easy to adjust the height.

Both of the lights you've linked will do super! You want at least 60w, since wattage will determine how close you have to put it to be effective (with 60w you'll want plants to be like 6inches away for it to be effective, less wattage and you basically have to have them touching), and then you'll look for full spectrum (6500k).

I have this light: https://www.amazon.com/VIPARSPECTRA-Reflector-Spectrum-Indoor-Plants/dp/B01B4GQ6MO

It's doing well covering a 2ftx2ft square shelf. I have about 20 plants under it and the next shelf down gets some trickle light because it's just a metal shelf and all my props are doing good under there.

You might want to look into a 250w there is a kit for 130$usd on Amazon
Edit: link link to 250w setup for $131 this is a great starter setup and will provide great lighting and includes most everything lighting related that you need. here is a 250w grow toutorial.
PS the yoyos are crap dont even try them. just buy the correct ones. yoyo's i dont have these cause i bought the expensive ones, but i hear these are good.

I actually didn't tally up the cost as that wasn't really of a concern to me, but I'll try my best to provide links to the things I bought for this. Feel free to add it up for me!

• Lighting
  
  • T-5 Grow light (came with 6500K bulbs)
    
  • 2700K bulbs
    
  • Grow light hangers
    
• Grow medium
  
  • Net Cups
    
  • Black Buckets
    
  • Black lids
    
• Nutrients
  
  • General Hydroponics Flora Series
    
  • General Hydroponics pH control kit
    
  • pH/EC/Temp Meters
    
• Grow tent
  
• Air ventilation
  
  • The only thing I ended up using from this kit was the cheapest part, the ventilation duct...
    
  • The fan from this kit is way too powerful for my setup because my humidifier couldn't keep up
    
  • I didn't use the carbon filter because I'm not growing weed.
    
• Water Distiller
  
• Humidifier
  
  • The cheaper the humidifier, the better. I first bought (and destroyed) one that had some sort of digital switch, so it would always be in the off state when you first supply power to it, meaning you can't turn it on/off with just a relay.
    
• Plumbing
  
  • Aquatec 8852 booster pump
    
  • 2 Gallon accumulator tank
    
  • Pressure relief valve
    
  • Tubing
    
  • Inline Pre-filter (Sorry they must have taken the product down...)
    
  • Misting nozzle T's
    
  • Tube ball valves
    
  • Analog pressure gauge
    
  • Misting Nozzles
    
    • Note that these nozzles are meant for WAY higher pressure systems (~1000psi) and I actually had to take out the spring for them to operate correctly, but they never clogged up, are easy to clean, and worked perfectly for me!
      
• Electronics
  
  • Raspberry Pi 3 kit
    
  • Humidity sensor
    
  • Pressure sensor
    
  • Water solenoid valve
    
  • 5V 4-channel relay module
    
  • Analog-to-digital converter
    
  • 24V to 12V converter
    
  • 24V Power supply
    
  • Resistor kit
    
  • Semiconductor kit
    
  • Circuit boards
    
  • Standoffs
    
• Wiring
  
  • 22 gauge stranded wire
    
  • 22 gauge solid wire
    
  • Power supply cord
    
• Connectors
  
  • Electronic Connectors
    
    • JST-XHP Connectors
      
    • JST-SM Connectors
      
    • Dupont Connectors
      
  • Plumbing Connectors
    
    • Bulkhead connectors
      
    • Quick-connect kit
      
    • NPT to quick-connect connector
      
      I also bought various tools, like crimpers, Dremel kit, drill, etc, but I don't consider those to be project-specific as I'll have them for the foreseeable future. Let me know if there's anything you see that you think I missed!
      

Just get an electric power washer with 2000 psi and this foam cannon from Amazon.

You may have to remove the original adapter the factory put on the foam cannon with the American standard in order for it to fit onto the sprayer.

Afterwards, enjoy!. Don't mind the spec sheet at the bottom of the list. It's outdated.

I've been using an MTM Hydro for ~8 years now, it's fantastic.

https://www.amazon.com/MTM-Professional-Adjustable-Cannon-Bayonet/dp/B00EDSLVQC

Buddy we need to talk. Get this at the very least..


General Hydroponics Flora Grow, Bloom, Micro Combo Fertilizer set, 1 Quart (Pack of 3) https://www.amazon.com/dp/B017H73708/ref=cm_sw_r_cp_api_i_dm.yDbM96AZS2

Past this grab this and you will have a decent perfectly colored harvest. Though there is much much more you can add to get a better harvest..


General Hydroponics CALiMAGic Quart https://www.amazon.com/dp/B00GZRKI40/ref=cm_sw_r_cp_api_i_on.yDbHNH497S

IMO the water your putting into your plant is wayyy to acidic. What I would suggest is to get some distilled water from the store, it can be either RO or steam distillation, and then add your nutrient additives. Your plant looks to be suffering from manganese and possibly a few other deficiencies, This is what I personally use and it should help.

All this being said I'm only on my third grow so there's still a lot to learn, hope this helps!

Don’t forget to get Cal-Mag too! You’ll need this with coco. Here’s the nutrient schedule he was talking about. Good luck!

This link might help you more than I ever could. Also the top comment is probably right get yourself some cal mag.

https://www.amazon.com/gp/aw/d/B00GZRKI40/ref=pd_aw_sbs_86_1?ie=UTF8&psc=1&refRID=30FM9SYKFJRWR6M44R1R&dpPl=1&dpID=81OFaANMmsL

Growboss
https://youtu.be/9ycNHK97-dg

t5 + racking

or ikea racking is ok too... with smaller 24 inch t5 maybe.

or even better, get a tent tent

I have a few, I started out with smaller feit LED bars (2ft) and after upgrading to a 4ft shelving unit I now have two 4ft t5 fluorescent units! I am finding it easier to get enough light out of the those, the LEDs need to be very close to the plants. The downside is that the t5 produces a lot of heat so need to make sure ventilation is good or it gets humid.

Here is the link to the t5 unit: https://www.amazon.com/4lamps-DL844s-Fluorescent-Hydroponic-Fixture/dp/B00HEYCRI8/ref=sr_1_5?ie=UTF8&qid=1478289944&sr=8-5&keywords=t5+grow+light

https://www.amazon.com/4lamps-DL844s-Fluorescent-Hydroponic-Fixture/dp/B00HEYCRI8 these lights are very bright, cheap compared to other lights. They are 250 watts and output more than enough light for your plants up to a max distance of 1 foot from the tip of your plant to the light. they cost around 75 bucks and are well worth the investment

My plants are inside from around now until Aprilish. I use a 48x18” shelf, 10/20 trays fit on it nicely. There is a cheap clip fan on the end of each shelf that runs 24/7, this is imperative. I have some of these lights and some of these lights– they work fine. They’re on timers for 12 hours or so. The LEDs are tricky because they’re too strong to put very close to the plants, oh well. I have another smaller shelf that’s basically the same set up for cuttings and seedlings.

Edit: fixed link maybe

Sure! It's pretty basic, actually. The table is a 4x2' stainless steel table from IKEA. Pretty cheap, but you could do cheaper, I just already had it. The heating pad is the same size (happy coincidence.) The cups are regular solo cups, most expensive element was the lights. You'll also want a timer, I use this one. And finally, the most ghetto part of the whole set up, the tent! I made it out of cardboard, tin foil and duct tape. Gotta save that paper.

Just get this. I've been using it in place of a bed in my apartment for 6 months.

http://www.amazon.com/Best-Choice-Products-Portable-Carrying/dp/B00LOZNXRC/ref=sr_1_6?ie=UTF8&qid=1464324103&sr=8-6&keywords=Vivere

https://www.amazon.com/dp/B00LOZNXRC/ref=cm_sw_r_cp_awdb_t1_rmOQAb82JYCY7

This is a lot like the one I got for forest. It's been great for forest and the back yard.

I wouldn't want to hike anywhere with it. But for close the car applications it's great.

It sounds like you're being exceptionally picky when you trim? Maybe relax a bit? Are you trying to get every single little bit of leaf out?

My wife and I use a bunch of these little bonsai scissors. We keep a glass of alcohol out to soak the gunked-up ones in and just switch them out as needed. It takes us roughly an hour to trim a plant.

Our basic process is:

• Cut all the branches and the cola off the plant.
  
• Put em in a big box in the center of the table.
  
• Lay out our scissors and other gear.
  
• Get the cat off the table.
  
• Stick a trash can by the table for the big stuff.
  
• We each grab a branch.
  
• Cut all the big fan leaves off and toss them. This takes maybe a minute per branch, probably less.
  
• Cut off all the little popcorn buds. We throw these in a bowl and save them for extracts. Maybe another minute per branch.
  
• Get the cat off the table.
  
• Now we start cleaning up the individual buds.
  
• Nip off any leaves that aren't sugary enough. Toss them. Maybe 5 minutes a branch.
  
• Start cleaning up the buds. We just nip off anything that sticks out too far. We're mainly just shaping things up. Don't worry about digging into the buds to get every little trace of a leaf. If you can reach it easily enough, great, but no need to stress. This is the bulk of our time, maybe 10 minutes per branch.
  
  Edit: Oh, and if you're totally fine just extracting the plant, you really don't need to do much at all. I'd cut the fan leaves off since its quick and they're just needless bulk, but even that isn't mandatory.

These are the best for trimming. They look shitty but once you get them you'll be amazed at the quality. Razor sharp and a single one lasted me through trimming 5 plants before I felt they could be sharper.

http://www.amazon.com/Bonsai-Pruner-Bud-Leaf-Trimmer/dp/B00P0FK7W6

https://www.amazon.com/gp/aw/d/B00P0FK7W6

I like these along with micro tip shears similar to the fiskars for larger leaves. These get a bit more precise for those little sugar leaves.

https://www.amazon.com/gp/aw/d/B00P0FK7W6/ref=mp_s_a_1_5?ie=UTF8&qid=1527029595&sr=8-5&pi=AC_SX236_SY340_FMwebp_QL65&keywords=bonsai+shears

These are by far my favorite for trimming sugar leaves. Super precise and razor sharp, makes it really easy to cut leaves precisely. Use any type of larger shears or scissors for stems and branches.

Did you watch the discussion video?

The wax in the measuring cup was barely liquid, it was quite manageable. I do agree that it would be nicer to have a melt pot and ladle the wax out from there. I've been eyeing this and this.

Yeah, wax does make a mess. I usually have a set of sheets set aside for wax play. I have been impressed with the beeswax as it's more solid when it dries and It was easy to clean up.

Soy wax is the absolute easiest as it washes out of most things.

I am using one of these personally with a pair of Eheim heaters:

https://www.amazon.com/Inkbird-Temperature-Controller-Thermostat-100-240V/dp/B015FKG4CC/

Just get an inkbird and turn the freezer down to the coldest setting possible. I attach the temperature probe to the side of my fermenter with some type of insulation. There is a couple options for warming as well if you do some light googling.

I think you are over-estimating the capacity of that car battery. You might be able to run a few LED lights for a few hours a day, like 2 or 3 hours a day maybe, but a constant draw of a cheap wifi camera (often not the most efficient possible power-wise), will kill that battery very quickly.

Let's say you wanted to run 12 Watts of LED lighting for 4 hours a day, and a camera (24 hours a day) which draws ~3 Watts.

12 x 4 = 48 Wh. Not much, but definitely substantial.

3 x 24 = 72 Wh. Again, not much, but substantial. This isn't going to be a 10 Watt panel type of deal here. :P

So, 120 Wh total. Or, ~10 Ah.

You'll need to account for cloudy days, so let's multiply that by 3.

360 Wh usable storage capacity needed, and 300 Wh generation needed each day.

You'll only get ~4 hours of good sun in a day, and panels put out ~60% or there about their rated power in the real world.SO...

360 Wh / 4 = 90 Watts.

90 Watts / 0.60 = 150 Watts.

​

So, you'll need:

1 x ~150 Watt rated solar panel. ( https://www.amazon.com/Newpowa-Moncrystalline-Polycrystalline-Efficiency-Module/dp/B00ZIZ6VY6/ should do.)

1 x PWM charge controller. ( https://www.amazon.com/ALLPOWERS-Charger-Controller-Intelligent-Regulator/dp/B01MU0WMGT/ or similar.)

Wire with MC4 connectors. ( https://www.amazon.com/BougeRV-Extension-Female-Connector-Adaptor/dp/B0753ZLLQB/ )

And battery cables to go from the charge controller to the battery, but you can probably buy some ring terminals at your local hardware store and use some 10 AWG stranded copper wire, don't necessarily need to order special ones if you can make them. :)

EDIT: You'll also want to fuse the positive side of the battery, solar, and load circuits. Choose fuse sizing for the wiring you use.

​

Now, the battery will die in a few months most likely if not sooner being cycled like this since it's not a deep cycle battery, but hey, then you can replace it with a good one. :)

Sure, I will try to list everything here, most of what I got was from Amazon.

$107 HQST 100 Watt,12 Volt Solar Panel

$20 Charge Controller from Amazon

$90 1000W Power Inverter I went overkill for most on this, but I wanted to power a chainsaw if needed, otherwise you would only need to put in $37 for something really good

$11 Battery to inverter cables

$64 35AH 12V Deep Cycle Battery

$14 12V LED lights

$5 light wiring

$6 Switch

$38 Solar Panel Wires

$13 Battery Cables

$16 Conduit Pipe

$17 Unistrut

$13 For the Satellite Mount on eBay

Then figure $20 for various nuts an bolts.

So for me it came out to about $434, but considering that I paid high for my inverter, and over paid on cables/wire (you can use cheaper cables, but I went with the pre-set ones for convenience), you could do it for just over $350.

I’ve had good results with these (the gold ones, the green ones aren’t as powerful). The top review goes into a ton of detail about their effectiveness.

https://www.amazon.com/dp/B0748D2SMB/ref=cm_sw_r_cp_api_It3UBbJZSTSD4

Sure, https://www.amazon.com/TaoTronics-Spectrum-Hydroponics-Organic-Wavelengths/dp/B0748D2SMB/ref=mp_s_a_1_1?ie=UTF8&qid=1538534159&sr=8-1-spons&pi=AC_SX236_SY340_FMwebp_QL65&keywords=Taotronics+grow+lights&psc=1

Thanks! For a lot of red plants co2, fertilizer, and high light will bring out their color a lot more and have them growing pretty fast. I have the 3 extra fixtures on my tank because I got two of those bulbs as gifts, and decided to get a third because I’ve found they do a lot for growth and color on my red plants. Also since this tank is pretty tall, I wanted to add a bit more light than what my beamswork light can do.

The beamswork lights are pretty good for planted tanks especially if you’re on a budget. I got the 36” full spectrum LED fixture for my 40 breeder for about $50 and it works great. If you want a lot of red plants I’d definitely go with a full spectrum WRGB LED fixture like this one. it’s the exact one I use. The one pictured in this post is a different one tho, it’s only got white and blue lights. You can check my previous post here to see what the full spectrum one would look like.

Here is a link to the pink bulbs as well.

I got a pair of cheap led light panels on Amazon. A blurple, and a white full spectrum. The blurple sucks and draws a lot of power. The full spectrum is just okay. I added two screw in Taotronics lights I had, and it made all the difference. Heat has also been a big issue for both panels. I've retired the blurple out of frustration with its poor quality.

When I started my garden, I could have gotten better lights, but I cheaped out. I regret that decision. You may be able to buy lights for half the price, but you will get what you pay for.

Fixed Taotronics light name. Added link to a similar light.

Terra cotta pots suck the soil dry, I don't use them unless it's for succulents. I would repot this in fresh potting soil inside a different container with a drainage hole. If this guy's soil usually looks this dry, and if it's more than 5ft from a super bright-ass window it won't grow. Everyone severely underestimates how close plants have to be to a window. And no growth is a sure sign of underwatering. If it was getting enough water but not enough sunlight, it would grow, just weirdly.

If you want zero guessing involved, I would read up on what that plant likes and pick up a super cheap moisture and light meter like this one from Amazon. Has saved me a lot of trouble when I have to check if a big plant is dry or if the sunlight isn't strong enough.

I use this one,
Use https://www.amazon.com/dp/B07BR52P26/ref=cm_sw_r_cp_api_i_CcTPCbC2B1JJ5

I bought this one and I really like it!

Only 8.5k lumens for 114w. (The main chip is the cree cxa3070, the epistar leds are just gimicky "full spectrum" crap) An HLG 100 would be a way better choice. 16k lumens at 96 watts with a good spread.

https://www.amazon.com/Horticulture-Lighting-Group-Quantum-Board/dp/B07C57J7XX/ref=sr_1_2?s=lawn-garden&ie=UTF8&qid=1535847710&sr=1-2&keywords=hlg+100

You can use either an overhead heat source like a ceramic heat emitter (they put off heat and no light) or an under tank source like an undertank heat pad. Any kind of source needs to be on a thermostat (such as this one) so it doesn't get too hot. IIRC, cali kings need a hotspot of around 85F.

It does sound like he's trying to shed. You may need to bring the humidity up a bit for him. Misting a couple of times a day with a hand mister might help him out (distilled or reverse osmosis water will prevent water spots on glass). Another option is to make a humid hide. Some kind of container that is completely sealed except for one entrance, with some damp sphagnum moss inside.
You can also provide him a deep water dish...big enough for him to lay in. My Florida kingsnake likes to lay in his water dish from time to time, but they like a bit more humidity in general compared to calis.

You need a thermostat. Place the probe between the map and the bottom of the tank. All below the tank. Inexpensive thermostats:

https://www.amazon.com/Inkbird-Temperature-Controller-Thermostat-100-240V/dp/B015FKG4CC/

https://www.amazon.com/MTPRTC-ETL-Certified-Thermostat-Germination-Reptiles/dp/B000NZZG3S/

This is a very common mistake, but it can have very deadly consequences if not changed.

Get a [thermostat](https://www.amazon.com/dp/B015FKG4CC/ref=asc_df_B015FKG4CC5396573/?tag=hyprod-20&creative=395033&creativeASIN=B015FKG4CC&linkCode=df0&hvadid=198107334619&hvpos=1o1&hvnetw=g&hvrand=14493505548356397280&hvpone=&hvptwo=&hvqmt=&hvdev=c&hvdvcmdl=&hvlocint=&hvlocphy=9018821&hvtargid=pla-326308171578 (I linked the one I have, it's not too expensive and it works great) as soon as possible, otherwise you risk burning your snake very badly, and the vet bills caused by that would be much more expensive than the thermostat, not to mention the emotional distress.

Fermentation temp will be higher than ambient, so 65-72 ambient could be pushing you out of optimal for some yeasts, though you could be fine.

I bought a chest freezer on sale and an inkbird temp controller and this works well for me and would fit in your budget. Even more so if you’re willing to find a Craigslist freezer. My (7 cu ft?) freezer can squeeze in two PET carboys if needed, though I currently just do 5 gal batches.

Hi! A little late to the party, but something else to keep in mind that I did not see mentioned is that you will definitely want a thermostat (not just a thermometer) to regulate the heat from your heat pad and/or Ceramic Heating Element. You will probably want one for each heat element, although CHEs can be controlled with dimmer switches as well I believe.

A thermostat lets you regulate the output of a heat pad or CHE. This is important because without regulation, it is possible for either of them to overheat beyond typical heating abilities. This could lead to extreme temperatures in your tank that could burn the snake or even cause neurological damage if it's hot enough.

I'm taking my list of suggestions from other users who post around snek subreddits as I am not yet a snek owner myself :(.

Cheap options are Jump Start thermostats, although they do not have safety features that will shut down the heating element if the thermostat fails. Another option that's in the same price range but a bit safer is an Inkbird thermostat. If you wanna splurge and get a very high quality thermostat for your little buddy, you can go for a Spyder Robotics thermostat.

Also, not necessarily required but useful and fun: an Infrared Thermometer

I have a 120 volt shaver, jig saw, variable speed electric drill, and more that get used occasionally. I got a $25, $20 with a coupon, inverter from Harbor Freight, the 400/800. It is sufficient. Often used stuff like phone charging and exhaust fan use 12 volts.

My mini van has one battery. The original starter battery got to the end of the warranty period and died. I replaced it with the biggest battery that would fit in the original location. That's a group size 24. I got the one with the most amp hours, 75, and the least cold cranking amps to attempt to get a deep cycle battery. It uses water so it might be deep cycle. It was $80 at Sams. A group size 59 starter battery was $100 so I saved $20. Deep cycle batteries like golf cart batteries shouldn't be discharged more than about 50% to avoid shrinking capacity. It is my opinion that starter batteries should be limited to 5% discharge. Batteries that are 12 volt and alleged to be deep cycle, like the one I got, should be limited to 15% to 25% max discharge. I'm looking for at least 3 years service.

I got a cheap charge controller like this:
https://www.amazon.com/gp/aw/d/B01MU0WMGT/
High priced charge controllers have lots of settings and stop charging and call that float. How they determine that the battery is full varies and they are often accused of battery killing. This simple controller has one voltage setting. When the sun comes up it connects the panel to the battery. The current is limited by the ability of the panel to produce. When the battery voltage gets up to the set voltage, mine is set to 14.4 in the summer, 14.6 in winter, the controller goes off and on keeping the battery at that level. Some people call that absorption. Then the sun goes down stopping the charging. When the absorption voltage is reached and the current tapers off to1% of the battery capacity, .75 amps in my case, the battery is full. For the controller to tell the difference between amps going to the battery and amps going to a load gets complicated.

My battery is flooded lead acid. When it gets over charged it makes hydrogen and oxygen by taking apart water. I check the water level. Since it does use water I take that as confirmation that it is getting fully charged. I keep track of how much water it takes. Thats 20 to 30 ml per cell per month. I also use a hydrometer to check the electrolyte specific gravity. 1.275 means it is charged. AGM batteries cannot be checked with these simple methods. Electronics to asses state of charge are $150 and up. Simple coulomb counters can tell you what you put in or take out but that isn't state of charge.
Whatever battery you get it has to be fully recharged or the capacity of the battery fades away.

My system is a $20 controller, $108 panel, $80 battery, $10 fuse box, $20 inverter. That's $238. Crimp terminals, crimper, wire, fuses, battery fuse holder, nuts and bolts, and some bits of heat shrink will go over $250. The single battery gets me alternator charging without a solenoid switch. Your $250 budget might be a bit short.

Another question - this one about grow lights. It gets pretty cloudy here, sometimes for weeks at a time, and I figure I would rather prep and make sure my new plants are getting enough light now so when winter comes it won't be an issue (Illinois does not get much sunlight then). My windowsills are small, though, so I'd like to set up a rack in the corner of the kitchen with lights and expand a bit. It won't be a huge area though.

​

I found these two grow lights and I'm not sure if one would be significantly better? The flexible one would be nice and more space efficient for me but would getting the bulb and a cheap desk lamp be better for the plants?

​

https://www.amazon.com/TaoTronics-TT-CL013-Grow-Light-Black/dp/B07JVGLGTD/ref=cm_cr_arp_d_product_top?ie=UTF8

https://www.amazon.com/dp/B0748D2SMB/ref=emc_b_5_i

​

Thank you!

This one works well for me, but it is expensive compared to the version on US amazon.

I got one of these and use it to help with watering. Its pretty awesome.

https://www.amazon.com/dp/B07BR52P26/ref=cm_sw_r_cp_api_i_cxGtDb2VK2P51

This is what has been recommended to me and seems to work:

Dwarf white or dwarf purple isopods are a good bet because they are generally too small for the ackie to notice and are tolerant of the high temperatures in the cage. I would consider getting maybe 10-20 and establishing a culture in a tupperware tub before introducing some into your ackie's enclosure. I have also had good luck with powder orange isopods. All three of these isopod types appear to breed pretty quickly so they should take off.

As far as springtails go, as with the isopods you want to establish a culture and let the population grow for a little bit before you begin adding bunches into the enclosure.

Some other tips:

• Add magnolia leaves (or any other good hardwood leaf) to your enclosure. As they decay they feed your isopods/springtails, but I also like them because they look nice in the enclosure and they appear to add enrichment for the ackie. My ackie likes to sniff them, flip them over, rustle them, just generally interact with and explore them. I got a bag of magnolia leaves off amazon.
  
  
• I was advised to get cuttlebone or sepia bone and place tiny bits in my cultures and the places in the enclosure where my isos/springtails hang out most. These items are super calcium rich, and isos/springtails benefit from it.
  
  
• Ensure your substrate is moist. Do not let it be super damp (especially toward the top,) but the substrate should be dark and more cakey down toward the bottom of the enclosure. I invested in a gardener's moisture meter to make sure the soil is moist enough.
  
  
• When misting or adding moisture to your substrate, consider using filtered water rather than plain tap water. If your tap water is well water or something, it may not be necessary, but for a lot of people like me unfiltered municipal water has a lot of chlorine and things in it that can be detrimental to the balance of the soil.
  
  Here are some helpful videos that should give you all the general info you need for establishing a bioactive enclosure:
  
  
• How to make an isopod culture
  
  
• How to culture springtails
  
  
• How to create a bioactive desert terrarium for ackies

Sonkir Soil pH Meter, MS02 3-in-1 Soil Moisture/Light/pH Tester Gardening Tool Kits for Plant Care, Great for Garden, Lawn, Farm, Indoor & Outdoor Use (Green) https://www.amazon.com/dp/B07BR52P26/ref=cm_sw_r_cp_api_i_FgLiDbZFW49K4

If you think it might be a watering issue (which it sounds like from the other comments), I really recommend a moisture meter to help you understand what's going on in the soil! With a pot that big, it's hard to tell how wet or dry things are--the "top 2 inches" rule doesn't really work.

I just got this one, but there are some even cheaper options on Amazon if you don't want the light/pH readings.

has there been any improvement over the past month? HERE is an article about proper care for your plant.

You stated that you only water when it seems dry but the article suggests once a week deep watering so that may be an issue. you also dont want to risk over watering so make sure your pot has good drainage at the bottom.

I highly suggest getting one of THESE and placing it in the pot to keep an eye one the light, water, and Ph levels.

Can you spend $10-15 on a moisture sensor like this ( https://www.amazon.com/gp/product/B07BR52P26/ref=oh_aui_search_asin_title?ie=UTF8&psc=1 ) ? That will be the easiest and most accurate way to see if your plant is too dry/wet. If it is drying out that quickly it may be in too small a pot, and you could consider repotting.

A 200W metal halide equivalent Horticulture Lighting Group Quantum Board might be worth a look.

two of these combos or however you want to do it.
https://www.amazon.com/Quantum-Board-Grow-Bloom-4000K/dp/B076QDKVDZ

https://www.amazon.com/Horticulture-Lighting-Group-USA-Quantum/dp/B07C57J7XX/ref=sr_1_fkmr1_1?keywords=horticul+lighting+group&qid=1559225906&s=gateway&sr=8-1-fkmr1

Also, you could look into DIY LED lights to save some cost. Ledgardener.com has good info.

Hey, I'm not OP, but thanks for the link I haven't seen these lights before.

Would you or anyone have input on an alternative cob light meant for plants that has similar properties and a substantially lower price? I have been thinking about getting a set of these for my photos. $450 for 3 vs $700 for 3. No mount for a tripod or stand, but I was thinking about using the 4 corner holes to attach some small bars or cable-wire for 4-way adjustment.

HLG 100 V2 4000K Horticulture Lighting Group Quantum Board LED Grow Light Veg & Bloom | Version 2 High-Efficiency Upgraded LM301B LED's https://www.amazon.com/dp/B07C57J7XX/ref=cm_sw_r_cp_apa_i_DOjXCb9VVADJE

I have purchased 3 of these and although I have no long term results they are working quite well for the price. My lettuce likes it. There is a slight pink hue but not as much as other led grow lights imo.

Hopefully Amazon links are ok:
https://www.amazon.com/dp/B07GGX3R9T

Sorry, I don’t know much about the strips and shelves - though I do use some on my reef tank macroalgae reactor (clear tube with led strips wrapped around) seems to work well and puts up with occasional salt water with out electrocuting me or fish. I don’t know how to fix them onto shelves tho.

I use these one on my plant shelves and added one of these just so it wasn’t bright red. You can see my shelves in my last post. They’re super low profile. But my shelves are wire mesh which allowed me to easily tie them to the underside.

This isn't bad. The price is pretty reasonable, and it will do fairly well in a smaller area.

Pardon my butt-in, I just got 2 of these for a tiny Serissa bonsai, will that not do anything? Is there a non-hanging better alternative? Thanks so much.

https://www.amazon.com/gp/aw/d/B07LG39B3M/ref=ya_aw_od_pi?ie=UTF8&psc=1

Are these bulbs better? https://www.amazon.com/SANSI-Daylight-Spectrum-Sunlight-Greenhouse/dp/B07P61K86G/ref=mp_s_a_1_4?keywords=sansi+grow+light&qid=1561981919&s=gateway&smid=A3HAQJT15PL4NZ&sprefix=sansi&sr=8-4

Right? I really dislike the idea of a purple light in my kitchen. ACKE LED Grow Light for Indoor... https://www.amazon.com/dp/B07GGX3R9T?ref=ppx_pop_mob_ap_share

I recently picked up a few of these and absolutely love them: https://www.amazon.com/gp/product/B07LG39B3M

Not hawking them, but not having to live with a purple glow all the time has been awesome, and my plants love it at least as much as the red/blues. I know a lot of people use them, but this little greenhouse / LED combo has been amazing as well: https://www.amazon.com/gp/product/B07FZTKYXV

I’m using this one. It was super easy to set up, but the thing is on the flimsy side and as you can see in the pictures, it’s really the bare minimum. No casing or anything. But it doesn’t get too hot and because it’s so minimal, it fits flat on the underside of the shelf so you don’t see it unless you’re sitting on the ground. Like I said in another comment, all this gear is super new so I can’t give any solid recommendation other than that I’ve had a good experience so far!

Thanks! I got it on Amazon

ACKE LED Grow Light

Here’s the link:
https://www.amazon.com/dp/B07GGX3R9T/ref=cm_sw_r_cp_apip_UvcJJIwRc5cwY

It comes with a hook so that you can hang it over your plants, but I liked the flat look against my shelves. I just used heavy duty command strips as it’s very lightweight, but we’ll see how they hold up!

They have ones that passthrough when they are being charged specifically for dashcams, they're expensive (Celllink B comes to mind). And the solar batteries are specifically meant for passthrough, but they are SUPER expensive. Something like this combined with some panels.


Edit: Celllink B only lasts ~20h. A big solar battery would make it a few days, would need to be charged at home I think.

https://www.amazon.com/gp/aw/d/B07LG39B3M/ref=psdcmw_14252941_t1_B07T1YG8BX
Here's one that's identical to the one I purchased but from a different vendor.

I have and use one of these - Jackery Explorer 240.

In my case though, this is NOT just for charging phones, I unfortunately need a CPAP machine, which this will power for a weekend. Also, I use it to power the fish finder in my little boat.

Yes. Jackery has solutions for this that people have posted great results with. both 12v and 110v capable, both are commonly used for pellet grills while camping/traveling.

Jackery Explorer 240

Jackery Explorer 500

My dad drove support for us and this worked for his machine!

Jackery Portable Power Station Explorer 240, 240Wh Emergency Backup Lithium Battery, 110V/200W Pure Sinewave AC Outlet, Solar Generator for Outdoors C https://www.amazon.com/dp/B07D29QNMJ/ref=cm_sw_r_cp_apip_TMcixEiiQUO8C

Sorry no idea. It shouldn't be so difficult to reproduce the id signal, but I'm not aware of anyone in this business, so there is only the Dell 18000.

USB-C PD seems a natural alternative, but 60W+ are rare and costly. Should go up to 100W, but search for 100W mostly finds crowdfunding projects ;) The circuit gets much more complicated.

Or this https://www.amazon.com/Jackery-Portable-Power-Station-Generator/dp/B07D29QNMJ

Should I get something like this for recharging my phone/laptop? https://www.amazon.com/Jackery-Portable-Power-Station-Generator/dp/B07D29QNMJ/ref=mp_s_a_1_3?keywords=camping+battery&qid=1566344296&s=gateway&sprefix=camping+batt&sr=8-3

Top tier has 2x Relassy 45W LED Grow Lights Goosenecks.

Bottom tier has 2x ACKE 20W Warm White LED Grow Light Panels.

That small pressure washer should work fine for spraying out screens. This is what I used for a while to connect a hose to the bathroom faucet..

Dude, My flat has no outdoor water faucet so I got [Indoor Faucet Adapter](https://www.amazon.com/Claber-8583-Indoor-Faucet-Adapter/dp/B000BPFYG4 and once connected I can run water through my wort chiller all day. Check the vid. https://www.youtube.com/watch?v=SJDSP7MvBiA

There are adapters available ( like this one or this one ) if you do want to use your sink.

I haven't used one of these but if you're able to clean your bike off on your balcony, this might be a decent option: http://www.amazon.com/Claber-8583-Indoor-Faucet-Adapter/dp/B000BPFYG4

Claber 8583 Koala Indoor Faucet Adapter https://www.amazon.com/dp/B000BPFYG4/ref=cm_sw_r_cp_api_U.CLzb96184GR

This might work for you.

A sink hose adapter runs $10-15 at any home improvement store and let's you connect a garden hose to a kitchen sink.

Edit: Apparently Amazon has them too

I use this takes a second to connect to the faucet.https://www.youtube.com/watch?v=SJDSP7MvBiA

go get some CY-kick cs off amazon get a sprayer and i swear to god you'll never have a problem. now don't go spraying this shit everywhere it can kill you and there are federal guidelines to using this. its used to kill scorpions and just about anything else.

You could always try setting a couple tokay geckos loose in your car. I'll be waiting for the "How do I remove tokay geckos from my car" post in a few days.

But seriously, if the problem is really that bad, I'd probably consider using an insectiside bug bomb, like Cy-Kick: http://www.amazon.com/Cy-Kick-Controlled-Release-Cyfluthrin-Insecticide/dp/B002ACMKV8

I use something like this to give it a good spray down any time it's subjected to salt. It's not as good as actually cleaning it, but certainly better than nothing.

I asked, and this is what we have. There's apparently a guide included about what dilutions to use for various pests and applications. He thinks he uses the second lowest concentration (second highest dilution).

You'd also need a sprayer. We have one of the hand pump sprayers. He thinks this is the one. He sometimes also uses a paintbrush for application around windows.

https://smile.amazon.com/gp/product/B0039EEN0M/ref=oh_aui_detailpage_o03_s00?ie=UTF8&psc=1

Got a couple of these, for cheap they work fine. One is for rinsing, one is for ONR pre-soak.

This made life a billion times easier to water the back https://www.amazon.ca/gp/product/B0039EEN0M/ref=ppx_yo_dt_b_asin_title_o02_s00?ie=UTF8&th=1

I use this one: https://www.amazon.com/gp/product/B0039EEN0M/ref=oh_aui_search_detailpage?ie=UTF8&psc=1

It works well, I usually will spray the bike, then apply a bike cleaning soap like the one white lightning makes, scrub the bike with a something like the pedros wash kit that they give away like candy, then rinse again.

Full album, http://imgur.com/a/UYQRW

Pressure washer: http://www.amazon.com/Joe-SPX3000-Electric-Pressure-14-5-Amp/dp/B00CPGMUXW

Foam lance: http://www.amazon.com/Professional-Foam-Lance-Adjustable-Bottle/dp/B004GNZYY4

Soap: http://www.amazon.com/Chemical-Guys-CWS40216-Super-Shampoo/dp/B00AFBXQNC

Towels: http://www.amazon.com/Chemical-Guys-MIC50706-Professional-Microfiber/dp/B00BQYCKE8

dispenser: http://amzn.com/B004GNZYY4
soap: http://amzn.com/B00BJCAPEE

I use these both to wash my car, check out chemical guys for more stuff. you need a pressure washer for the dispenser. but you can find ones that connect to the garden hose as well but won't output as much foam.

edit: personal picture of them in action: http://imgur.com/OpIw4PJ

very high quality, and I kinda thought about the price as well but then put it into perspective. A 600w grow kit cost less than the two 300w leds which are actually around 180 true watts. two of them in my 36x36x78 is wonderful, not great but sufficient. one 300w led in my tent would not be enough though, I need two so it makes sense they're not very expensive yet beautiful quality. I would only worry that the delivery service handles them with care. I was lucky and both arrived in perfect condition from UPS.

You amurrica eh? This was on Amazon
https://www.amazon.com/dp/B005ECZQTY/ref=cm_sw_r_cp_awdb_jCNGzbKHZ98YS
Let me try to help you figure this out. These will give off quite a bit of heat (which is great for winter northerners) but summer can get pretty hot. You will want to seal off the room somehow as well, like the other comments said, fuck bugs! This can be hung maximum 1.5 feet before you burn the plant so you might be ok with some training.

600 watt will cover about 4 x 4 foot area so squish each plant in that space roughly and bunch all the branches up like roses, this will give a good lollipop shape and save space but at the same time maximize the light of the main colas. I just hope you have enough headroom for flower stretch!

Hopefully you have some fans laying around to simulate a gentle breeze and help temp control. I try to be as crafty as possible before spending a ton of money, (the light was an exception). Use what you have around the house or go to dollar stores for like white paint sheets to create your own tent for cheap, until you can invest more.

Goodluck, hopefully this ramble is useful to you!

I have this light.

So I can just shove it in the corner of a dark room with some panda plastic and it will be fine for the veg stage? Is it crazy/stupid to be thinking about closing off the corners with some cardboard/plywood or something? So it's like a little square area, top open, that the light will hang over?

I started with 100 bucks bought 4 t8 shop lights from home depot, 2 pieces of plywood, and 4 5 gallon buckets. Used organic miracle grow and was in business.
I got like 4 ounces of bud from that investment, but it was a pain too use and I had so many problems, that the 2nd and 3rd harvests; were so bad I was dry for 3 months.

But I've learned a lot since than if you have the money, these items will save you the bullshit that i went through.

600w grow light $200

[Carbon Air Filter]
(http://www.amazon.com/gp/product/B0052ZPMAG/ref=oh_details_o09_s00_i00?ie=UTF8&psc=1) $175

Some Bubble pack insulation at home depot $50-100

[General Organics]
(http://www.amazon.com/General-Hydroponics-Box-Starter-Kit/dp/B004PS4B08/ref=sr_1_1?ie=UTF8&qid=1367524539&sr=8-1&keywords=General+Organics) $40 starter box will last one cycle

these should get you through your first grow np. and I've already recouped all of the money I've spent on these items with the first harvest, I was paying 350 an ounce before hand to a dealer and now for way pennies on the dollar I have the dankest dank around and it's fucking awesome fucking awesome.

Reading is ok but once you get started you'll realize that most things people post are bs and the best way to learn it is to just do it, and experiment on your own; most things look much harder than they actually are.

I feel so liberated now that I can produce my own and the money that you save omfg the money you save.

Given that there's no such thing as a BIFL filtration system of any kind, the DIY recommendations here are rather reasonable. I quite like the furnace filter + box fan suggestion.

If you want something a little more robust, look into getting a carbon filter and a fan to go with it. I think the usual recommendation for carbon filters is for 24/7 use they need replaced every year or two. Here's one on amazon that you could use with a 6 inch fan which would add pretty good circulation for a large room: http://www.amazon.com/iPower-GLFILT6M-Control-Australia-Charcoal/dp/B008NYF8S4/ref=sr_1_2?ie=UTF8&qid=1396198801&sr=8-2&keywords=carbon+filter

This one comes with a fan: http://www.amazon.com/VenTech-IF6CF620-Inline-Virgin-Charcoal/dp/B0052ZPMAG/ref=sr_1_5?ie=UTF8&qid=1396198801&sr=8-5&keywords=carbon+filter

Not that great of a deal, but still: iPower GLFILT6M Air Carbon Filter and Odor Control with 1050+ IAV Australia Virgin Charcoal for Inline Fan, 6-Inch, Pre-filter Included, Reversible Flange https://www.amazon.com/dp/B008NYF8S4/ref=cm_sw_r_cp_api_fPozzbEXNQYCV

I have that Variac and vortex combo and love it; look for the amazon used section I pick it up for 110 instead. I have this fan and it works wonderful for a 2 x 4 tent PACKED TO THE FUCKING BRIM with plants. Tis cheaper. Edit: it's the one you linked... woops!

I'm just tossing it out there that you can pay with amazon prime card on rapid LED and get this vastly superior light I was told of tonight. I used the prime credit card to get LEDs there. ;)

What are you going to put the plants in?

A small 6 inch carbon filter with intake. I actually used this brand and many of their larger sizes. Intake should be 6" and cost appx. $40, worth it , electric is minimal clears the air of your whole apt (if under 600) you will actually notice cleaner air (I'm in LA and these have always made a diff from my small college apt by the freeway to the house I live in the hills now, would never grow without a nice carbon filter set up even when I move to Mendocino (Plus They create a nice ambient sound, increase C02 (bud size) and you should cut down on mold issues) not sure what part of the world you are in but filters in humid or arid, small or large grow, are key and worth the small investment for several reasons) If you're skeptical do some research.

https://www.amazon.com/iPower-Charcoal-Prefilter-Included-Reversible/dp/B008NYF8S4/ref=sr_1_3?ie=UTF8&qid=1501722851&sr=8-3&keywords=6+carbon+filter

CFM won't matter regarding if it can push air through the filter. What you want to look for is the static pressure rating of the fan. It will be in the unit of mmH2O. Try to get a fan rated at 6 mmH2O or greater. Basically, the motor must be strong enough to push air through a thicker medium like a filter.

My fan (Delta AFB1212HHE-F00) is a 120mm PC fan rated at 9mmH2O and 120 CFM. My other fan (Scythe Kaze 3000) is also 120mm PC fan rated at 6mmH2O and 133 CFM. Both push through my homemade carbon scrubber.

Also, from what I've read, you don't want to use a carbon 'fabric' like those sheets. They wear out quite quickly and making a filter from small activated carbon granules would be superior. You might be able to find one relatively cheap like this. You could attach a 6-to-4 inch rubber reducer like this and let it sit on top of your fan on the cabinet. I made my scrubber out of an atrium grate, pantyhose, rubber reducer and the carbon and it sits right on top of my bucket with no need to seal around it as the air pushes through nicely with not much back pressure.

I have a 6" fan. This filter works great. $62 bucks.

https://www.amazon.com/gp/product/B008NYF8S4/ref=oh_aui_detailpage_o09_s02?ie=UTF8&psc=1

My LED has the same connections and I ended up not using the connectors it came with at all and got 4 of these: https://www.amazon.com/dp/B0098R0600/ref=cm_sw_r_cp_apa_56PPybPHJ6F4D
Connected them from the tent top bars and directly to the hooks on the lights. Can basically raise it right up to about 1-2 inches from the ceiling.

First off, i'm simply recommending them, the stuff you got works but theyre a bit over priced so i'm going to recommend a few cheaper stuff.

You can get away with a 4'' fan/filter/duct with the grow space tent you provided. heres a recommended one.
https://www.amazon.com/gp/product/B004Q2ER5C/ref=oh_aui_detailpage_o08_s01?ie=UTF8&psc=1
Your tent and led is fine
Ph up and ph down is fine as well, i recommend getting a digital ph and ppm meter combo on amazon, doesnt matter if theyre cheap, they'll work.
As for your timer, i highly recommend this https://www.amazon.com/gp/product/B0042I5FF6/ref=oh_aui_detailpage_o07_s00?ie=UTF8&psc=1
That timer will give you the ability to upgrade to two led if you want too in the future.
Don't forget hangers for the lights.
https://www.amazon.com/dp/B0098R0600/ref=twister_B00FL6MTJI?_encoding=UTF8&th=1
Everythign else seems fine.

You can keep the light that far away from the plants throughout. You can also play with the height. Get those ratchet light hangers. They are adjustable. Like These

The 300w does not really cover much space. For reference in my tent I am growing 2 plants right now. I used only the 300w for veg and just let them veg longer to make up for the lack of light. No problems for me there. As for flower you'd want more than one if you are doing more than one plant. In my tent, as I said, I have two going right now. I have a 250w HPS that's over one plant and the 300w is over the other.

To summarize, the 300w will be perfect for one plant throughout the entire veg/flower cycle. The 300w will be adequate to veg 2 plants but not enough to flower. Maybe with your cfls and the new ones you are adding plus the 300w you should be good for 2 plants.

Awesome to hear! Yeah I scoured the net too and tried a few designs before deciding on this one. It's just a simple PVC frame I hung from the top of the tent using adjustable light ropes.

Here's the materials with some example links and short instructions. I was sort of winging it at the time I built.... so let me know if you have any more questions and I can take some closer pictures of the screen or something. :)

 

Materials |
---------|
| 1" Schedule 40 PVC pipe - Frame edges. |
| 1" Schedule 40 PVC 90 degree elbow. |
| 3/4" Truss-Head Screws |
| White Twisted Mason's String Line |
| Light Rope Hangers |

 

| Short Instructions |
----------|
| 1)) Measure out Length x Width you'll need for frame pieces. (accounting for the inch or two that gets added by the elbows when they're on) |
| 2)) Cut 4 pieces of pipe to desired length and fit them together using the 90 degree elbows. I used a rubber mallet to make sure they were seated all the way into the elbows. |
| 3)) Once the frame is assembled, you may have to twist it a little to make sure it's completely flat. My first attempt was a little tweaked by having an elbow rotated slightly. I just twisted the frame a bit to fix it and made sure it laid on the ground completely flat. |
| 4)) Grab a ruler and start marking out the spots where you'll drill for the screws. I start at the elbow and make a mark every 2". Continue this all the way around. You'll want to make sure the holes lineup perfectly even with the holes directly across. Just for a visual aid, If the screen is leaning up against a wall - you'll want to mark the top & bottom edges first, then the left and right sides. This way you make sure you don't accidentally end up with any angled or diagonal strings going across when it's done. ;) |
| 5)) Drill the pilot holes in the side of the pipe you marked previously. I drill all the way through the pipe wall and stop when it hits the opposite wall. |
| 6)) Screw in the truss-head screws about 75% of the way. Just enough to make them secure but also leave enough room to wrap the Mason's String around. |
| 7)) Once all the screws are in, I pick one corner as a starting spot and I tie up the string there and bring it across to the matching screw. From there it's just a time consuming game of rounding the screw next to it, bringing it across, rounding the next screw, bringing it back across, so on and so forth. Whatever weaving technique you want to use here is fine. |
| 8)) Hang the completed screen at the desired height by attaching the adjustable light rope hangers and you're good to go! I threw some zip ties around the elbows and clipped the rope hangers to those. |

My Setup:

• Lumin Tekco Indoor Grow Tent, 36"x36"x72" - $84.99
  
  
• Apollo Horticulture 6" 440 CFM Inline Fan with 6" Carbon Filter - $134.99
  
  
• Roleadro 2nd Generation 600W LED Plant Grow Light - $139.99
  
  
• Adjustable grow light hanger - $9.04
  
  
• Temp/Humidity Monitor - $11.65
  
  Quick question.....Should these lights still be 12" above the young seedlings? I think right now I have them hanging between 12-15"
  
  Also will I need a second light later on in the grow when the 2 plants get bigger?
  

I use this one with my ARBlue 390SS and Meg's Gold Class. It has two adjustments, one to change the shape of the spray and another to adjust ratio of water:soap mix. I'm not sure exactly which foam lance you have, but if it doesn't have a dilution adjustment, that may be the issue.

You could also try increasing the soap:water ratio in your bottle to get it thicker, to see if that helps instead of buying a new foam gun.

Edit: Changed link to proper model for electric power washers. Thanks, TimeToGrowThrowaway

I have the Karcher k2.300 electric pressure washer. Make sure you get the MTM Cannon that is designed for Karcher washers.

You'll want one of these if you want to clean your car:
http://www.amazon.com/MTM-Hydro-Professional-Adjustable-Foamer/dp/B00EDSLVQC/ref=pd_sbs_lg_2?ie=UTF8&refRID=1MMC8X642WWZG9R5J25W

Of course it may be cheaper to just go to those self-service car washes, as they're about five(ish) dollars a visit. I bought a ton of car stuff and it was quite a bit more than five dollars, and I don't think I will ever break even as I am rarely in the mood to drag out all the stuff to wash my car... but I don't regret buying them as it is nice to really wash my car on a nice day and really get in touch with it and fix any issues I find.

But those self service car washes are fun too! Grab a bluetooth speaker or hope the place plays music and rock out.

Just a note, if you get the MTM foam cannon made for electric power washers like the sun joe you will get thicker foam than the one you chose. That one is more suited for more powerful power washers.

https://www.amazon.com/gp/product/B00EDSLVQC/ref=oh_aui_search_detailpage?ie=UTF8&psc=1

Also, if you haven't seen already my setup is here: https://www.reddit.com/r/AutoDetailing/comments/8hnuto/my_budget_friendly_wallmounted_sunjoe_w_aquarium/

Nah, theyre like $150 for a decent one.

https://www.amazon.com/gp/product/B00CPGMUXW

https://www.amazon.com/gp/product/B00EDSLVQC

I bought my SunJoe SPX 3000 pressure washer and MTM Hydro back in February 2016 and it's still working as of now. I have plans to swap the hose for a longer hose and a new gun. I'm not a fan of the longer wand style gun that comes with it.

This is foam cannon you want to use with electric pressure washers. It's designed to be used at a lower pressure. And 1500psi will work. Just don't expect it to make the kind of foam you see in the CG videos.

Not too sure yet,i was thinking of getting this stuff? https://www.amazon.ca/gp/product/B00GZRKI40?pf_rd_p=46535598-d2e0-4bc4-8392-182d8c1e93fc&pf_rd_r=XJGKD3YKE5GMFD90T0MF
then i read that I could add epsom salt to the water (1tbsp per 5 liters) and that would help with magnesium. Still not sure what to use for calcium. Or if i should just purchase calmag on amazon

These are the ones I currently have for my 4x4 that work well https://www.amazon.com/gp/product/B00HEYCRI8/ref=oh_aui_detailpage_o07_s01?ie=UTF8&psc=1.

Within the next month i think i'll be binging on these https://www.amazon.com/HydroplanetTM-Fluorescent-Included-Horticulture-Gardening/dp/B019J3UPUS/ref=sr_1_1?s=lawn-garden&ie=UTF8&qid=1487146972&sr=1-1&keywords=t5

I just recently brought all of my plants in for winter and upgraded my light setup to 4 T5 fluorescent bulbs at 6500 kelvins. Does this look like an appropriate height to keep it above the plants? The jade is about 3 inches from the bulbs so I'm a little worried about damage. I've been thinking about moving the jade to another window and just lowering lights closer to the rest of the plants. Also any advice on how long to keep them under lighting every day would be useful!

https://i.imgur.com/C8Vt1YJ.jpg

Just in case anyone was curious where I got this setup. It feels very sturdy and I'm definitely glad I bought it. I'd just recommend buying longer chains to hang it since the ones they provide are pretty short.

https://www.amazon.com/gp/product/B00HEYCRI8/ref=oh_aui_detailpage_o00_s00?ie=UTF8&psc=1

I'm growing plants on a table using the following grow light from Amazon.

https://www.amazon.com/gp/product/B00HEYCRI8

I bought $16 worth of 1" PVC to build the stand for it. (Shout out to Jeb Gardner for the stand)

Here's a picture of that light mounted on the stand.

https://i.imgur.com/HZ5Bgkv.jpg

It's actually my bedroom. I'm limited on Space and it's hard to strike a balance between bedroom and jungle lab so I've mostly given up and you can see which way it's gone. ..

As for the lights I can tell you which ones I've been getting but I don't feel like I have used them long enough to actually recommend them. If that makes sense. They were 75 for the 4' 4 bulb model.

I also use screw in led bulbs in places and led clip lamps in others. There are also finex led 24/7 aquarium lights.
https://www.amazon.com/gp/product/B00HEYCRI8/ref=oh_aui_detailpage_o03_s01?ie=UTF8&psc=1
I hate mirrors but I've started putting them behind plants to bounce more light. The inexpensive sort of generic full length mirrors go well on the back of 4' shelves. Dollar stores seem to frequently sell small plain mirrors to go behind individual plants.

Fwiw I'm also loving this humidifier https://www.amazon.com/gp/product/B01M4O49V9/ref=oh_aui_detailpage_o03_s00?ie=UTF8&psc=1 the plants are happier and the mammals including humans breathe better with it. I'm a big fan of humidifiers in general though. Years ago I got tired of low humidity. It's such a small investment compared to the financial cost of losing plants. Plus the frustration and sadness of unhealthy ones...

Here's what I've brought to multiple festivals. Couldn't recommend more. You can adjust the hooks to make it more or less taut which can help keep your back from getting sore if you're not trying to sleep in a U shape.

Somebody recommended this stand alone hammock. These will comfortably fit under an EZ Up. I've seen two of these under one, they work well!

https://www.amazon.com/Best-Choice-Products-Portable-Carrying/dp/B00LOZNXRC/

It's 9 feet but with the hooks all the way down my camping hammocks don't have any issues. They're 10.5 to 12 feet long.

I sleep in the cloth hammock it comes with. It will stretch a good amount the first few hangs.

I bought a hammock so I could have a place besides my bed where I could lounge in pain. They actually support my back much better than I expected, I've accidentally fallen asleep in it because of how comfortable it is. The hammocks without spreader bars aren't the unbalanced tippy things that most people are used to.

What are your health problems? The only thing you mention needing to worry about is your bed. Food/snacking is an issue I always have, it's hard to keep and prepare the diet I require with my issues.

This is the hammock I bought because it comes with a stand. https://www.amazon.com/Best-Choice-Products-Portable-Carrying/dp/B00LOZNXRC/ref=sr_1_7?ie=UTF8&qid=1497307361&sr=8-7&keywords=hammock

Mine might have been a different brand, but it looks like this one
https://www.amazon.com/Best-Choice-Products-Portable-Carrying/dp/B00LOZNXRC/ref=sr_1_7?ie=UTF8&qid=1496260090&sr=8-7&keywords=hammock

VERY minimal trees in GA, but if you’ve got your heart set on hammocking at your camp, check this out! I’m in maplewoods so I don’t need it for forest but I’m considering getting it anyway for my yard.

https://www.amazon.com/Sago-Brothers-Pruning-Scissors-Trimmer/dp/B00P0FK7W6/ref=sr_1_6?ie=UTF8&qid=1494649320&sr=8-6&keywords=trimming+scissors+for+marijuana

These things changed my life, can trim twice as fast with these as other snips.

these are the ones I got

They’re amazing dude. The spring comes from the metal at the end. It’s basically two razor blades springing together. I don’t think I could go back to any type of actual scissor type shears after using these now. Also they’re cheap so if you didn’t want to clean them and just chuck a pair that’s a viable option as well. But they don’t make my hands hurt compared to the others so that’s the biggest thing for me next to how well they cut.

Try these. I still love fiskars but i found these to be better for a lot of trimming

https://www.amazon.com/gp/aw/d/B00P0FK7W6?psc=1&ref=ppx_pop_mob_b_asin_title

These are the ones I got and I've been pretty happy with them so far. I'd love to get some nice forged ones someday though.

I live in an apartment so I can't modify the faucet. This thing works like a champ.

http://www.amazon.com/dp/B000BPFYG4/ref=cm_sw_r_udp_awd_hFwwtb1DQ7V53

You can try this item from amazon. It gives you a hose connector without the need of threads. I used to use it when I brewed inside. http://www.amazon.com/Claber-8583-Indoor-Faucet-Connector/dp/B000BPFYG4/ref=sr_1_1?ie=UTF8&qid=1320278321&sr=8-1

I mean.. I'm in an apartment lol. There is barely enough room for me let alone water barrels! I like the idea though. I ended up ordering a clamp thing from Amazon (Claber 8583 Koala Indoor Faucet Adapter https://www.amazon.ca/dp/B000BPFYG4/ref=cm_sw_r_cp_apa_i_JbArDbCCE0QDB). It seems to be working! Just was difficult to figure out if it would fit the specific faucet before ording.

http://www.amazon.com/Claber-8583-Indoor-Faucet-Adapter/dp/B000BPFYG4/ref=sr_1_11?ie=UTF8&qid=1412103740&sr=8-11&keywords=hose+adapter

This is so easy, Get a Indoor Faucet Adapter Walmart sell's them also. Check out a video https://www.youtube.com/watch?v=SJDSP7MvBiA I have one and been using it for almost a year with no problems, Takes seconds to attach and use.

It looks like you could use a claber koala

https://www.amazon.com/dp/B000BPFYG4/ref=cm_sw_r_cp_apa_i8QEzbKHZ0JMW

I have one to hook my counterflow chiller to my sink, and it works great. My only concern is that the aerator seems to extend down a bit.

I got the 4 stage 50 GPD and it's been good so far.

I only have a 7 gallon and 9 gallon tank. So, I don't need much for water changes and top-offs.

I have a 7 gallon jug with a spigot which makes dispensing it very easy. I fill two 1 gallon jugs throughout the week for top offs and water changes.


It takes about 2.5 hours to fill the 7 gal. It varies with temperature.

I've heard you can get resin for the DI cartridge and save a lot more money that way versus replacing the cart each time.


Oh yeah, I use this faucet adapter instead of the included one. If your faucet is compatible, it makes connecting and storing so quick if you need this kind of solution.

$10 sink adapter would have worked, or this adapter for even cheaper depending on your sink

I have this to water plants on my balcony: https://www.amazon.com/dp/B000BPFYG4/

You may get better flow out of one of the other fittings but this thing is super easy to use if your faucet is the right shape for it.

Dude. Buy this. You don't ever have to worry about roaches again Cy-Kick CS Controlled Release Cyfluthrin 16oz Insecticide https://www.amazon.com/dp/B002ACMKV8 don't mess with traps or anything else. Mix with water and spray around house, any entryways as well as nooks and crannies

honest question, besides termites, what is your opinion on this DIY solution

http://www.amazon.com/gp/product/B002ACMKV8

rotate every other application with:

http://www.amazon.com/Talstar-Insecticide-Termiticide-Bifenthrin-Mosquitoes/dp/B00409QKRY/

+
http://www.amazon.com/gp/product/B004HD42E6
+
http://www.amazon.com/gp/product/B002Y2GNVM
+
http://www.amazon.com/HomeRight-C800909-Deck-Sprayer-1-Gallon/dp/B00C10E80A/
+
http://www.amazon.com/Scotts-71133-Hand-Held-Broadcast-Spreader/dp/B0000BYCP7

Just a suggestion, get a sprayer at Home Depot and a professional treatment chemical and do your own spraying (saves a TON in the long run).

I've had great luck with Suspend SC and CyKick CS (seems better for bad infestations).
Suspend SC: https://www.amazon.com/Suspend-SC-Contact-Insecticide/dp/B004FEP174/ref=sr_1_1?gclid=EAIaIQobChMI88DPj4Gk5AIVFrbICh2rnw2gEAAYAiAAEgIq8fD_BwE&hvadid=153731892840&hvdev=c&hvlocphy=9012551&hvnetw=g&hvpos=1t2&hvqmt=e&hvrand=17148506663456322785&hvtargid=kwd-180414180&hydadcr=15246_9501196&keywords=suspend+sc&qid=1566941813&s=gateway&sr=8-1

Cykick CS: https://www.amazon.com/Cy-Kick-Controlled-Release-Cyfluthrin-Insecticide/dp/B002ACMKV8/ref=sr_1_1?keywords=cykick+cs&qid=1566941932&s=gateway&sr=8-1

Edit: These are both food/pet safe once they dry. We usually put the dog and cat in one room and spray the rest of the house, then spray the room they were in when the rest is dry. Both chemicals are odorless when dry.

/u/bagodees posted this info (in respect to roaches at least) a long time ago and it has worked wonders for me:

They are much worse at apartment/townhouse condos since there are so many people and so many connected units all in one building. Here's the deal: when you see one, it's got at least 47 buddies that are behind you laughing at you because you can only actually see the guy that's running in the spotlight. The traps and sprays you get at the local stores don't work, and actually make the roaches worse because that's how those pesticide companies make money. The same deal goes for the pest guys that the apt management contracts with - if all the pests disappear, then their business dries up.
That said, there's hope for you. I have found that the only stuff that works are these two products:
http://www.amazon.com/gp/product/B002ACMKV8?psc=1&redirect=true&ref_=oh_aui_search_detailpage
and
http://www.amazon.com/Advion-Cockroach-Gel-Bait-4-syringes/dp/B002Y2GNVM/ref=pd_sim_328_20?ie=UTF8&refRID=0GTNZZ7FKR4006TZM0TM
You can get a standard 1 gallon sprayer at Home Depot for the Cy-Kick CS. Spray that shit around your problem areas. The gel bait is for if your problem is really bad - place those in the same areas until you don't see anymore roaches.
These products are highly toxic, but they do work. Just make sure you follow the instructions, wear protective equipment when applying the pesticides, and keep your pets away from treated areas.

I used to be an exterminator when I was going to college. If they are big roaches they usually don’t live inside your house. When I was an exterminator the company I worked for used the pesticide linked below. Spray this around your house and focus on doorways or any place you think they might come in from. You only need to spray that once a month. The suggestion for the German roaches is great but German roaches are small not large. So maybe google German roaches and see if that’s what you have and decide on your plan of attack. Good luck!


BASF - 792075 - Cy-Kick CS - Insecticide - 16oz https://www.amazon.com/dp/B002ACMKV8/ref=cm_sw_r_cp_api_i_28KpDb4135E8R

I've got a solution for you, but you won't like the price tag. Grab a container of this awesome stuff and any old one-gallon yard sprayer. Mix as instructed and spray the inside of your home and outside too if it's a house. You and your room mate will be the ONLY living things in your home for a few months. It's safe for pets too as long as you let the spray dry before turning them loose in a treated area.

http://www.amazon.com/Cy-Kick-Controlled-Release-Cyfluthrin-Insecticide/dp/B002ACMKV8

I've used this stuff before. worked wonders.

http://www.amazon.com/Cy-Kick-Controlled-Release-Cyfluthrin-Insecticide/dp/B002ACMKV8/ref=sr_1_1?ie=UTF8&qid=1381889202&sr=8-1&keywords=cyfluthrin This is what the pros use.

Here is what I use,

Kills everything. You mix 1 oz in a garden spray with 1 gallon of water.

Spray all the base boards and under your sinks and cabinets.

​

https://www.amazon.com/gp/product/B002ACMKV8/ref=ppx_yo_dt_b_search_asin_title?ie=UTF8&psc=1

​

If you really want to get rid of them, get one of those cheap pump sprayers and some Cy-Kick and you're good to go. This is what some professionals use for insect control. It works great. I use it (spray along house borders inside and out) and after that my home is insect-free for months. You'll see some dead bug carcasses the first few days and then nothing.

Probably better off keeping it simple, more than a hundred bucks less and will never run out of batteries - https://www.amazon.com/Chapin-International-617407731200-20002-Multi-Purpose/dp/B0039EEN0M/ref=sr_1_7?keywords=pump%2Bsprayer&qid=1568512164&s=lawn-garden&sr=1-7&th=1&psc=1

$15 can solve the problem somewhat more elegantly.....

https://www.amazon.com/Chapin-International-617407731200-20002-Multi-Purpose/dp/B0039EEN0M

I use one to hose the salt off in the winter when then hose is shut down for the season.

marry a weed sprayer with a sink sprayer

Assemble the brand new never used weed sprayer, but instead of using the wand, splice in a sink sprayer.

Heat water on the stove to about 110 °F, pour it in the sprayer and pump it up. You will probably want a wash cloth for this and a draft free environment. Maybe a second bucket of warm water to wash with, leaving you most of the spray to rinse off with, but it's optional.

You need to take a navy shower with this rig, but it will get you clean.

If you use this in the cabin's shower stall you'll have to get some RV antifreeze to pour into the plumbing traps before you leave.

I bought a solar shower like this for my first year. I never used it. All the girls in my camp would use up all the water before I got a chance. I don't really like it anyway. It's fucking heavy when it's full and a bitch to carry, especially if you're far from water. I wouldn't recommend it.

I've seen some people hook up showers like mine in little tents like this, which is probably nice for privacy's sake, but if you're gonna spend all that money, you may as well just buy a shower pass and use the showers at Roo.

Someone at our camp bought a garden sprayer like this, which I thought was genius. It works great, you just need a buddy to spray you down.

In all honesty, I just use water jugs and pour them over my head in the mornings. Two gallons is exactly how much I need and it's simple and cheap. Plus, you never really want hot water anyway. It's so fucking hot out all the time that cold/room temperature water feels fucking great.

Bifen XTS Bifenthrin Concentrate 1 Quart https://www.amazon.com/dp/B007SI74GA/ref=cm_sw_r_cp_api_i_CCAUDbCHKBS84

You’ll also need a garden sprayer

Chapin 20002, 2 Gallon Lawn, Garden and Multi-Purpose Sprayer with Adjustable Nozzle, Translucent White https://www.amazon.com/dp/B0039EEN0M/ref=cm_sw_r_cp_api_i_qDAUDbYZ169P3

Also, it’s not a bad idea to get a respirator, this stuff is strong. I picked mine up from harbor freight but here is a link to a similar one.

Breath Buddy Respirator Mask (Plus Safety Glasses) Reusable Professional Breathing Protection Against Dust, Pollen, Pesticides, and Organic Vapors - Perfect For Painters and DIY Projects https://www.amazon.com/dp/B01M67SJ0S/ref=cm_sw_r_cp_api_i_-EAUDbF7988H6

I don't know of any actual stores you can buy one from, but you can get it from Amazon for pretty cheap compared to Chemical Guys. (I assume from you saying "California")

http://www.amazon.com/Professional-Foam-Lance-Adjustable-Bottle/dp/B004GNZYY4/ref=sr_1_1?ie=UTF8&qid=1394840710&sr=8-1&keywords=mtm+foam+cannon

Is this the same one? But for non-karcher (SunJoe)? https://www.amazon.com/dp/B004GNZYY4/_encoding=UTF8?coliid=IJOZ1NS7ZQPR&colid=1X845QHCWNHBH

I'm asking because it doesn't say 2600 psi in the title of the listing.

I just bought a Ryobi pressure washer this week. I bought this one. Yes, the one I bought will clean concrete and decks, not sure about the one you posted though. Here is the front walk at my house midway through using the pressure washer, without any detergent.

I bought this foam cannon to go with it. I read after the fact on here that people recommend going with the lower pressure version of it for a low-pressure electric pressure washer. However, it still made pretty good foam! I used CG Honeydew, 5oz to make that foam.

I don't own a PC, so I can't comment. I've got a RUPES 21 and highly recommend it, but it's pricey.

EDIT: Because I'm an idiot my original comment said I bought the pressure washer you linked. I didn't. It was another Ryobi one (fixed now). I looked at the URL and got confused because I'd looked at so many recently and thought it was the same one. Sorry -- hope I didn't mislead you!

If you have a Sams Club membership. This is the one I have Sams Club It works great had it for about a year now nothing has gone wrong with it. If your going to get a foam cannon I have Amazon hooks up with the quick disconnect. It won't clean concrete or house siding as quickly as say something with 3,000 PSI but it gets the job done. I'm happy with it.

Edit:The one thing I don't like about it is the hose from the pressure washer to the wand is not very long I have to move the pressure washer around to rinse my SUV. Yea first world problems. The electric cord is very long so thats great.

Sorry for graveposting, want to make sure I grab the right foam cannon:

This is the low psi version: Professional 2600 PSI Adjustable Foamer
and this is the high psi version: Professional Foam Lance Adjustable with 32 oz. Bottle

right? it looks like the low psi version doesn't come with quick disconnects, which I'm pretty sure I need to connect to my pressure washer, right?

I'd get a fine grade nanoskin mitt or something similar for decon. Maybe a foam gun or foam lance and some soap. Might want to grab an APC for interior cleaning, although I think you can dilute ONR down as an APC... I really like Optimum APC though, very safe and effective.

I saw this today on slickdeals, choose subscribe & save to get it down to $13.35: 1-Gallon Chemical Guys Maxi-Suds II Super Suds Car Wash

1. Iron X is a completely different product than Sonax. Iron X is for decontamination and is more for your paint where as Sonax is an actual cleaner that is designed to work on your wheels.
   
   
2. The very best spray bottles you can get for the money are the HDX Widemouth Sprayers.
   
   
3. Check Harbor Frieght for M105 /M205 and use the digital 20% off coupon. You will have to make 2 seperate trips inside but you can use the same digital coupon from your phone.
   
   
4. Foaming guns are a good thing to have. If it is for a pressure washer, make sure you get the short handle with the largest capacity bottle you can get. When you try and put those things on the end of the PW wand, it will spin in the collet and not go where you are wanting it to. This is the one that I have.
   And this is the handle for the unit
   
   
5. Not sure what pads you are referring to but if you are talking about buffer pads, then the best deal flying on what I think are the best pads out there are the Buff N Shine multiple pad pack
   
   
6. I keep the majority of my equipment in a couple of Husky Job Boxes
   
   
7. I keep my pads and MF towels in a couple of these Sterilite Drawer Carts
   
   
8. To keep mold and mildew out of all of my totes and carts, I also throw in some Silica packs
   
   
9. For all of my chemicals and supplies I keep everything on a simple set of Metal Shelving
   
   Best of luck.

I have the SPX3000 also, great pressure washer for the amount you pay. I have this foam cannon and it works great with it.
(http://www.amazon.com/Professional-Foam-Lance-Adjustable-Bottle/dp/B004GNZYY4/ref=sr_1_3?ie=UTF8&qid=1448944408&sr=8-3&keywords=mtm+foam+cannon)

Foam Guns made by Gilmour $35.79
or $38. The orange foam gun's price fluctuates a lot.

MTM Foam Lance $59.99 shipped.

I don't know about best, but amazon has it at https://www.amazon.com/gp/aw/d/B004GNZYY4/ref=mp_s_a_1_1_a_it?ie=UTF8&qid=1469576875&sr=8-1&keywords=mtm+foam+cannon&pi=SY200_QL40

Mods: is this is a problem, please delete.

This [MTM Hydro] (http://www.amazon.com/gp/product/B004GNZYY4/ref=s9_hps_bw_g121_i1) is probably one of the most popular ones out there.

I got this one it's more expensive but should be the same mechanically. I use a 1700PSI Greenworks pressure washer and get great results http://imgur.com/a/sCGn4 like others have said just adjust the knobs and make sure it is assembled correctly and that you are using the right adapters (if needed). also I use McGuire's gold class soap, the soap could be your problem.

http://www.amazon.com/gp/aw/d/B004GNZYY4/ref=mp_s_a_1_5_a_it?qid=1457622601&sr=8-5&keywords=mtm+foam+cannon

I have a Mars 600 I use in my veg tent, and its great for tight node spacing in early veg.
But I flower with HPS, and its worth it IMO
If I could only pick one it would be a MH/HPS kit over cheap LED no question.

I have one of these and like it
https://www.amazon.com/Apollo-Horticulture-GLK600LS24-Digital-Dimmable/dp/B005ECZQTY/ref=sr_1_1?ie=UTF8&qid=1484365758&sr=8-1&keywords=600w+hid
I also have the large reflector cool tube version, but it cost more and doesnt cool any better than the other hood.

Interesting. Do you mean something like this?

https://www.amazon.com/Apollo-Horticulture-GLK600LS24-Digital-Dimmable/dp/B005ECZQTY/ref=sr_1_5?ie=UTF8&qid=1494802924&sr=8-5&keywords=hps+600watt

My fan was on the out-take pulling air out of the tent. This is what I used for ventilation http://www.ebay.com/itm/VenTech-4-6-Inline-Duct-Fan-with-Carbon-Filter-and-Variable-Speed-Controller-/181246860768

My light setup is: http://www.amazon.com/Apollo-Horticulture-GLK600LS24-Digital-Dimmable/dp/B005ECZQTY

No, but here's the first one that pops up when you search on amazon

Apollo Horticulture GLK600LS24 600 Watt Grow Light Digital Dimmable HPS MH System for Plants Air Cool Hood Set https://www.amazon.com/dp/B005ECZQTY/ref=cm_sw_r_cp_api_YMP4ybBEE64H8

> Or you could hop on Apollo Horticulture 600w air cooled digital MH/HPS ~200$ and get a higher yield than that

Yeah, price & yield are definitely factors.

On the Apollo, would you recommend the cool-tube model

• http://www.amazon.com/Apollo-Horticulture-GLK600CT24E-Digital-Dimmable/dp/B00521B894/ref=sr_1_3?ie=UTF8&qid=1421257310&sr=8-3&keywords=Apollo+Horticulture+600w
  
  Or the standard air-cooled version:
  
  
• http://www.amazon.com/Apollo-Horticulture-GLK600LS24-Digital-Dimmable/dp/B005ECZQTY/ref=sr_1_2?ie=UTF8&qid=1421257559&sr=8-2&keywords=Apollo+Horticulture+600w
  
  Definitely worried about heat in the smaller tent.

Imo you'd be better off getting a cob setup with cbx 3590 or vero 29 cobs this site has some good options to choose from. If you want to try out something different with good coverage and efficiency check out qb boards. If you want something affordable, yet powerful go with a 600/1000 mh/hps light. If you just want a basic cheap led light marshydro 300w(132w actual) is a good start.

Ok, so I am scrapping the 2 smaller CFLs that I have and selling them on Ebay and amazon. I am going with a package like this that includes a 600W HPS and MH bulb, timer, and an Aircool hood.
Does dimming them essentially reduce the Kelvins without sacrificing wattage? Or will both be reduced? Or am I completely wrong haha.

We were using CFL's for vegging and LED for flowering. Our LED light is just a really thin strip so I don't think it's distributing enough light out to the plants. I just bought a 600w HPS: https://www.amazon.com/gp/product/B005ECZQTY/ref=oh_aui_detailpage_o01_s00?ie=UTF8&psc=1


We're growing in a basement. It can get fairly cold in the winter so hopefully the HPS will even out the temp a little. Otherwise we do have a space heater we can turn on occasionally.

I was planning on just setting up an oscilating fan in the bud room. But with this new money I was thinking we could get the actual 6in fan that goes in the hood.

Do you use ducting for ventilation? Is it possible to connect the ventilation from the grow room to the ventilation from the dryer or water heater thing? There are ducts that go right through the grow room. Otherwise there's a window in the grow room but it's pretty easy to see from outside. I don't need it to be super discreet since it's medical but I don't want to advertise what we're doing either.


I also was considering getting an actual grow tent. Right now we kind of just surrounded the area where the plants are with mylar from emergency blankets and tents. I'm a little worried about them getting either too hot or not being sealed enough to keep the light in.

Any thoughts on the above info is definitely welcome :) We're very much new time growers. We harvested once and it was a pretty small amount, but we got high off of it! So goal semi accomplished haha

So then this one right?

https://www.amazon.com/gp/aw/d/B005ECZQTY/ref=mp_s_a_1_4?ie=UTF8&qid=1499052997&sr=8-4&pi=AC_SX236_SY340_FMwebp_QL65&keywords=600W+hps+grow+light&dpPl=1&dpID=51w9ciKiSYL&ref=plSrch

Thank you for your advice! I have been looking at Mars Hydro LEDs on Amazon. I see a 300w for $90 or a 600w for $159. Do you think it's worth the jump in price to go with the 600w for a smaller scale grow? I was looking at HID kits as well, for nearly the same price as the 600w Mars Hydro you can go with this option as well http://amzn.com/B005ECZQTY

Thanks for your insight, it is greatly appreciated!

What size fan (cfm)? What size ducting? I used this carbon filter in my 2x4x5 tent with a 6" 400 cfm inline fan. Worked great.

Yea some filters are just poor quality especially the small ones. I run this filter and it's worked great. http://www.amazon.com/iPower-GLFILT6M-Australia-Pre-filter-Reversible/dp/B008NYF8S4 it's also able to be flipped.

No, that’s crazy expensive. You want a cylinder like this https://www.amazon.com/iPower-Scrubber-Australia-Reversible-Prefilter/dp/B008NYF8S4/ref=mp_s_a_1_3?ie=UTF8&qid=1549037948&sr=8-3&pi=AC_SX236_SY340_QL65&keywords=ipower+6+inch+carbon+filter&dpPl=1&dpID=51gvYylKTpL&ref=plSrch

Here is how I do it. Tent on right gets first air ( the coldest and driest as it's for flowering ) air moves to second tent ( the air is warmer and more humid now, ideal for vegging flowers),the air moves into the dry tent,which usually has it's own dehumidifier. Finally exhausting thru a carbon filter back into the room.

https://imgur.com/a/IkN2T9W

I hope this inspires ideas. It wont smell like cannabis in the exhaust air until like 2 weeks into floweing, from that point it progressively gets WAY stronger. I highly advise a carbon filter if you want stealth. I found this to work amazing ( iPower GLFILT6M 6 Inch Air Carbon Filter Odor Control Scrubber with Australia Virgin Charcoal for Inline Fan, Reversible Flange, Prefilter Included https://www.amazon.com/dp/B008NYF8S4/ref=cm_sw_r_cp_apa_i_J3bWDbSH6F9XR )

hope this all helps you 😎

Why do you want to inline it?

And if you want to inline it, why not buy a regular filter and put it in a box and be done with it? For 2 tents you can get away with a fairly cheap filter for below 50$

Take this random one of Amazon...

https://www.amazon.com/iPower-Charcoal-Prefilter-Included-Reversible/dp/B008NYF8S4/ref=sr_1_4?s=lawn-garden&ie=UTF8&qid=1503753117&sr=1-4&keywords=carbon+filter

It even has screws so you can replace the coal if it gets old

You can just blow the air out of the filter

-i use a BreatheRight by Allen for my allergies. It’s expensive ($600-ish) but if you get the charcoal filter it’s crazy good. Will remove scented candle smells and Bacon smells as well as the very marijuana smoke that I smoke inside my own apartment.

I haven’t received any complaints. It’s been 2 years.

The next thing would be to go one step higher and purpose an in-line fan filter and attach a huge 24” charcoal filter.

This option is actually WAYYYY more effective, but requires just a little bit of knowing how to put stuff together, and it’s slightly loud, but god damn, it totally cleans all smells and allergies.

This first link is for an in-line fan:


https://www.amazon.com/gp/aw/d/B07FPFVZTZ?pf_rd_p=731c2082-c3b6-4ec5-ba3b-337a0516607d&aaxitk=i0llSkJCSVXgMhex-F1n.Q&hsa_cr_id=3570293760101


Second link for the filter:

https://www.amazon.com/gp/aw/d/B008NYF8S4/ref=psdcmw_5446824011_t1_B07FPFVZTZ


Third link is for the Allen Breathe Right:

https://www.amazon.com/Alen-Customizable-Purifier-HEPA-Pure-Allergies/dp/B00APO426E/ref=mp_s_a_1_3?keywords=allen+breath&qid=1574290745&sr=8-3


The Allen is more aesthetically pleasing and is a complete unit that requires zero installation. Simply plug and play. This model is for 1100sqft. If you get this, get the charcoal filter. They have lots of filters.


The in-line fan and filter option will be like 10x more powerful and way more affordable than the Allen, but unpleasant to look at and is louder.

This fan

6" Inline Fan - 395 CFM Exhaust Duct Fan, Built-in Speed Controller, ETL Listed, Pre-Wired 6 FT Grounded Cord - Great Use in Grow Tent with Carbon Filters, Light Fixtures, Intake. Fits 6 Inch Ducts. https://www.amazon.com/dp/B01L0D0UEQ/ref=cm_sw_r_cp_apa_i_5YNSCb9Y7EARS

With this filter

iPower 6" Inch Air Carbon Filter Odor Control with Australia Virgin Charcoal for Inline Fan, 420 CFM https://www.amazon.com/dp/B008NYF8S4/ref=cm_sw_r_cp_apa_i_6ZNSCbGZX32RJ


Just know that when you open the tent. Shits gonna smell ..

This is still a work in progress

Details:

Essential shoping list (to me)

-[6" fan and carbon filter]
(https://www.amazon.com/gp/product/B008NYF8S4/ref=oh_aui_detailpage_o00_s01?ie=UTF8&psc=1) works great, no smell, plenty of airflow, relatively loud at 100%, virtually silent when turned down to below 30% with some sound absorbing foam around the intake and fan. 4" would have worked for my small setup. I'm pushing through the filter which is outside my grow area with no problems. Don't forget some ducting and real duct tape. Clamps aren't really needed at these speeds and pressures if you have good tape, but they won't hurt.

-[Speed controller for fan.] (https://www.amazon.com/gp/product/B006NGI2RS/ref=oh_aui_detailpage_o06_s00?ie=UTF8&psc=1) This was definitely overkill, I just didn't trust cheaper voltage regulators, plus I can and have used it for other things. Pretty well made, works great.

-[pH meter.] (https://www.amazon.com/gp/product/B00CMFVXMA/ref=oh_aui_detailpage_o05_s00?ie=UTF8&psc=1) I didn't want to cheap out on this since pH is so important. Meter works great. Only note is you probably want to get some extra storage solution, it only comes with a little, and after a few months you'll run out.

-Light was a Viparspectra 300 (130 actual watts). Worked well, had good growth. I added more light later but for my small space that would have probably given me decent yields.

-[This timer for lights] (https://www.amazon.com/gp/product/B01MYOD58S/ref=oh_aui_detailpage_o01_s00?ie=UTF8&psc=1) was super easy to program and hasn't failed. It has a bright blue LED indicating if the timer is sending power to the lights which is nice, but I had to tape over it because it was so bright. Also, the timer gets a little warm which makes me a little uneasy since I only have ~250 watts going through it.

-General Hydroponics FloraGrow, FloraMicro, FloraBloom, CaliMagic. I also got Fox Farms Big Bloom part way through flower but don't have any way to know its actual benefits so it's not an essential.

-Coco for growing medium. Most people add perlite, I didn't.

-7 gal smart pot

-Plastic storage container with a kitchen cooling rack to sit the pot into and onto and allow drainage without making a mess. Cooling rack allows for 1/2" of water to accumulate before the pot is sitting in it.

-[adjustable hangers for lights.] (https://www.amazon.com/gp/product/B0098R0600/ref=oh_aui_detailpage_o00_s00?ie=UTF8&psc=1) Work great, easy to use



Set up and process

• In a closet that's 1.8' x 1.8' x 6'
  
  
• Temperatures between 72 F and 80 F. When I measure temp at the bottom of my canopy it's consistently about 5 degrees F below the temp at the top near my fan outlet. I have to use A/C in the room to keep it from moving up to 80 or a bit higher.
  
  
• Humidity between 40% and 60%
  
  
• Coco with about 30% peat moss which included time release nutrients. I didn't want the added nutes and tried running water through it for a few hours to clear it out, but I highly doubt that did anything. I wish I had waited a few days to ship pure peat moss so I could know exactly what nutrients were going into the plant. I picked peat moss because I wanted my pot to hold more water. I'm not sure if this was a good thing or not.
  
  
• 7 gallon smart pot, only ~5.5 gal full though. I'm glad I went with the bigger pot since my plant is so tall and top heavy now. I have read that if you want to go bigger for the pot it's better to go deeper than wider because of the root structure, but I don't know.
  
  
• I sprouted the seed using the paper towel method. Took a few days. Next time I'll probably use the water in a shot glass method.
  
  
• I put the sprouted seed right into the 7 gal smart pot which probably wasn't a great idea. I also watered the entire pot for the first couple weeks which probably was bad. I should have started in a small container and transplant, or at least only water a small area around the seedling at first.
  
  
• I put a bag seed in the same pot and sprouted it because I was dumb and bored. It sprouted and actually got to about 2.5 weeks old before I pulled the trigger and dug it up and transplanted it into it's own 5 gal smart pot. It wasn't happy for a few days because I know I damaged the roots in order to try to avoid the roots of the main plant. I let it grow in the new pot until about 4 weeks then I ran out of room in my closet and trashed the entire plant. Terrible idea all around.
  
  
• Viparspectra 300 initially, then around day 50 of veg I added ~100 watts of CFL. At 40 days after the 12/12 flip I added a galaxy hydro 300 and took out the CFLs (we'll see if that was a good idea...)
  
  
• Veg for 60 days after sprouting. Good idea if you have the vertical space and time. Veg took a long time because I waited too long and the first time I topped I took off like 3 or 4 sets of growth tips, it was like a whole mini plant. I don't know if waiting so long helped the plant develop more roots and a bigger stem which facilitated faster growing or if it was just wasted time. I'm going top it earlier next time though.
  
  
• I topped it twice to get kind of a manifold. The height and size of the colas were not dependent on where it's branch started which makes me doubt the need of a symmetrical manifold, which this was not.
  
  
• Defoliated a little around the 12/12 flip, a lot during about 20-30 days after flipping which left the plant with virtually no fan leaves with stems longer than 1". This was all great, next time I'll probably defoliate earlier.
  
  
• I had to go out of town for 10 days just after the 12/12 flip. I raised up the lights, but not enough and one cola grew into a CFL and killed the top. I cut the top off and now the lower flowers are growing a bit bigger and taller than their partners on other colas, just no top. Also, I only got an automatic watering system set up the night before I left and it didn't water as much as I wanted, plus the pH drifted a lot while I was gone. I started with the pH low to try to mitigate it rising, which I expected. I was expecting the plant to really be struggling, but she looked great actually.
  
  
  
  
  
  
  
  
  
  
  
  

I have a different LED but maybe this can help.

This is my current grow: http://imgur.com/a/FnEdV (The second picture in the album shows the hook)

and this is the 300 watt light that I have: http://www.amazon.com/ViparSpectra-Reflector-Spectrum-Indoor-Plants/dp/B01B4GQ6MO?ie=UTF8&psc=1&redirect=true&ref_=oh_aui_detailpage_o00_s00

Our hooks might be different but maybe this will give you an idea on how to hang it

Also these may be the hooks you are looking for: http://www.amazon.com/Apollo-Horticulture-Adjustable-Improved-Internal/dp/B0098R0600/ref=pd_bxgy_86_img_2?ie=UTF8&refRID=05TYKJTTZ9XTFCD7SRCJ

You need these... Adjustable Lighting

I'd recommend spending just a little more and getting ones with metal gears like these. The iPower ones came with my lights and I do not trust them to hold, they are very cheaply made. The carabiner is tied on and the internal gears are plastic. Now I use the cheap ones as backups for my ducting or filter in case my straps slip.

I have mine currently on my laundry room shelf with an LED light. Ha. Nice setup. I don't have any reflective insulation right now since I will be moving mine outside soon. But next year I plan on it. Would you say it's cheaper to do that or just get a tent?

Anyone curious, this the LED and hooks I have:

https://www.amazon.com/gp/product/B01F53LP46

https://www.amazon.com/gp/product/B0098R0600

I just picked up a greenworks myself just to clean off my car quicker and no trips to the car wash during winter.

I noticed that on the electric power washers the soap attachment is NOT anywhere near as good as the MTM foam cannon my buddy has on is. So I did a quick order on amazon.

The one you need for Karcher is this one https://www.amazon.com/MTM-Hydro-Professional-Adjustable-Bayonet/dp/B00EDSLVQC

You need one of these :D MOAR FOAM

http://www.amazon.com/Professional-2600-PSI-Adjustable-Foamer/dp/B00EDSLVQC/ref=sr_1_6?ie=UTF8&qid=1450935166&sr=8-6&keywords=foam+cannon

I use an MTM hydro pro cannon with a sun joe SPX3001. Would recommend to anyone.

MTM Hydro Professional Adjustable Foam Cannon with Bayonet, 2600 PSI https://www.amazon.com/dp/B00EDSLVQC/ref=cm_sw_r_cp_api_i_xUSdBbDACF0TX

We have an entry in the wiki regarding this question. https://www.reddit.com/r/AutoDetailing/wiki/pressurewashers . I personally use this foam canon and I love its performance. It comes with 3 adapters, it should have the quick disconnect fitting you need. https://www.amazon.com/gp/aw/d/B00EDSLVQC/ref=yo_ii_img?ie=UTF8&psc=1

I got the SunJoe. Have only used it a couple of times, once on my car and once on my small entryway and rear patio (10x10 concrete slab covered in northwest moss/mold). It has performed perfectly on both occasions.

For me, the SunJoe hit the "sweet spot" of features, power, and price. It was $149 at both Amazon and Home Depot (online order only). I went with Home Depot for an easier return in case I wasn't happy. Comes with five nozzles for variety of options (widest 40-degree spray for car rinse, 15-degree did the rear deck just fine). Motor is not quiet, but at least it only runs when you're actually using the sprayer.

As one other user noted, the hose is a bit short - I think it's 20 feet. I own a VW Golf, and with the machine a few feet from the front of the car, it took a bit of a reach to be able to foam the back (I live in a townhome and my wash space is a bit tight). 30 feet would be optimal. That said, the hose material seems sturdier than the "roll up" hoses that come with the Ryobi and PowerWorks washers that I inspected closely at Home Depot and Lowe's.

Speaking of build quality, when you read online reviews, it seems that every brand has problems with longevity and bad "out of the box" units. All of the consumer-grade electrics I inspected seem the same kind of Chinese mass-market build quality. They might last 7-8 years of light duty use, they might leak the first time you use them. Caveat emptor. The SunJoe's two year warranty where almost everyone else offered one was a selling point for me.

One other thing worth noting: MTM Hydro makes two different foam cannons. One is specifically designed for pressure washers under 2600 psi. This is the one you want to get: http://smile.amazon.com/gp/product/B00EDSLVQC?keywords=mtm%20hydro&qid=1458490183&ref_=sr_1_1&sr=8-1

Here's the one I use:

http://www.amazon.com/gp/product/B00EDSLVQC/ref=oh_aui_detailpage_o04_s00?ie=UTF8&psc=1

It's heavy duty, and I really like it. The foam in this shot isn't all that great - but it's because I chose to really just get it soaking to get the grime off. Plus, I use chemical guy's which is probably the best around (IMHO) but isn't quite as snowy as others I've used.

Hmm, i'm not sure about the tablets, but I know there is a liquid form made for plants you can buy like this stuff.

You need to flush 2-3x the size of your pots. Use dolomite lime as a dry amendment in your future grows for cal/mag.

General Hydroponics CALiMAGic Quart https://www.amazon.com/dp/B00GZRKI40/ref=cm_sw_r_other_apa_i_0U-ACbGSZA5BJ

Any cal/mag works, but some brands have added nitrogen. Which can be good or bad.

well they don't look dead yet so that's good

have you seen any bugs hopping around or under the leaves?

what soilmix are you using?

My guess would be calcium deficiency or calcium absorption issue since you aren't providing it in either of the ferts you stated. get some lime or calmag see if that helps.

if you are aware of overwatering i assume you aren't doing it. letting the soil dry out some before watering. like only once or twice a week?

calmag is pretty universal from my understanding so shouldn't be a big deal. You'll use so very little even if you feed everyday. It should last you a few grow cycles.


here is GH cal mag pretty cheap I'm also in canada https://www.amazon.ca/General-Hydroponics-GH1772-CALiMAGic-Quart/dp/B00GZRKI40/ref=sr_1_fkmr0_2?ie=UTF8&qid=1543512680&sr=8-2-fkmr0&keywords=gh+calmag


​

​

https://www.amazon.com/General-Hydroponics-GH1772-CALiMAGic-Quart/dp/B00GZRKI40/ref=mp_s_a_1_3?keywords=cal+mag&qid=1559147159&s=gateway&sr=8-3


This ones least expensive cal mag don’t gotta be used too much only if you see signs of def.

Also I’ve heard of the epsom salt method I believe it works

I feel like your pinching pennies with the oysters.

https://www.amazon.com/General-Hydroponics-GH1772-CALiMAGic-Quart/dp/B00GZRKI40

I use RO water and 1 of these lasted my first grow. Through all the flushes and mess ups I did too.

I usually do 7.5 ml per gallon of water for cal mag.

https://www.amazon.com/General-Hydroponics-GH1772-CALiMAGic-Quart/dp/B00GZRKI40/ref=sr_1_6?keywords=cal+mag&qid=1572977992&s=lawn-garden&sr=1-6

General Hydroponics CalMag

Calmag plus is from Botanicare, you're using all GH except for your calmag which is botanicare?

My res is going cloudy when adding silica directly to water, then phing to 7, then adding calmag, then everything else and the phing again.

I can't figure out why and was thinking it might be because I'm using GH silica and Botanicare calmag. But if you're using those two and not having issues it's gotta be something else. Still probably gonna buy CaliMagic like right now since my calmag plus is basically empty

The worst part of it going cloudy is it takes atleast 8 hours to go cloudy so figuring out what fell out of solution is a bitch

Edit- just found that GH does make a product called CaMg+ as well as CaliMagic...

I can't even figure out what the difference between the two is on their website. Just going to buy Calimagic now and hope using GH Silica/Calmag solves my issue

http://generalhydroponics.com/calimagic/?rq=calimagic
http://generalhydroponics.com/camg/?rq=CaMg%2B

Epsom salt because it's part of the Lucas H3ad formula. Calimagic because the plants have been showing signs of magnesium deficiency, and now calcium too, if that was the rusty spots are.

Ooh interesting ..

I bought this ;

T5 Grow Light (4ft 4lamps) DL844s Ho Fluorescent Hydroponic Fixture Bloom Veg Daisy Chain with Bulbs https://www.amazon.com/dp/B00HEYCRI8/ref=cm_sw_r_cp_api_i_rsskDb87P981B

So the fluorescent could take away humidity and moisture faster? Which LED lights did you get? I’ll definitely get a timer switch ! Great idea you just time 12 / 12 right

I was thinking of a cheaper fixture this time like this one

Legit get one of these and you'll be just fine no need for a giant filter/fan system: https://www.amazon.com/4lamps-DL844s-Fluorescent-Hydroponic-Fixture/dp/B00HEYCRI8/ref=sr_1_6?ie=UTF8&qid=1510932370&sr=8-6&keywords=t5

something like this will be fine https://www.amazon.com/4lamps-DL844s-Fluorescent-Hydroponic-Fixture/dp/B00HEYCRI8

Here's the link again to my first album after initial setup for reference: http://imgur.com/a/fvzkZ

1. I used round PVC mainly due to availability, price, and associated parts. I saw a design that allowed for the adjustment of the water level within the pipes by rotating the end collar on the round PVC and I liked that approach. There are way to accomplish this with a flat channel system also, but I found this method acceptable. As far as my research has shown, a "proper" NFT system does use flat bottoms (as seen in pretty much all commercial operations), but the round PVC approach is very common for hobbyists like myself. I can't comment on very detailed reasoning for the true "film" technique on the bottom of flat pipes vs round. It appears to me though that people get plenty of good results out of both setups, so I personally wouldn't (and didn't) get too hung up on it.
   
   
2. In the linked gallery above, the 5th image (this one: http://i.imgur.com/KSkFZEc.jpg) you can get a decent look at how the water is sent to the pipes. Most pumps vary, but I basically used a piece of flex tube to connect from the pump output to an adapter into the ball valve, then from there pieced together with various connecting parts, a threaded riser pipe used in irrigation, and then three of these: Riser Adapter. There are probably a million different ways, this is just what I came up with and it's working fine without leaks (plumber's tape.. use it).
   
   
3. I spaced my holes 6". This seems to be a commonly recommended spacing for leafy greens. I staggered the outer pipes (with 8 holes each) 6" from the inner pipe (has 7 holes) to maintain this spacing. Yes, more space will be better for larger plants, but I don't ever plan to use this setup for anything but various lettuces primarily, and some other leafy greens. Seems like most people grow larger plants that may require more spacing in different systems completely though, like DWC buckets, dutch buckets, etc.
   
   Hope this helps. I spent many hours on and off for a year researching before pulling the trigger on this system. In case you are wondering, here's the light I bought: Light It seems to be working very well so far with good output (~20,000 lumens) for 216 watts.

If you can put a little money into this, you'd get better veg out of a 4' T5 fixture, and it'll put out more heat. Keep the tent pretty much closed up, with a vent on the bottom barely open and a 6" duct fan hooked to a Programmable Thermostat venting out the top. While it's cold, you can set the fan only to kick on at 80 degrees or something, so you aren't venting out warm air constantly. You do need some airflow, and the thermostat makes it a "set and forget" kind of thing. So you aren't baking plants on an unusually hot day, or taking away their heat on cold nights.

Other ideas:

• Have the tent sitting on some kind of insulation. Cardboard is better than nothing. Styrafoam is best.
  
  
• A cheap heating mat under the plants, if you can't get the inside above 55 degrees at all times.
  
  
• 1020 planting trays to collect water runoff. 4 of these fit nicely in a 2x4'. Or just use the cheap circular planters from any garden shop.
  
  
• For little veg tents, I just rest a power strip on top and plug everything into it. Keeps electric away from any water, and out of your way.
  
  
• Not sure what water drainage you would need? You don't need to water to crazy amounts of runoff right now. And, if you are in trays or planters, the extra water will get absorbed by the plants. If you are holding these in 3g pots for 8 weeks, make sure they are cloth pots. Then the plants can easily drink their own runoff. And you won't get rootbound.
  
  
• 8 weeks is a long time. You can fill a 2x4' with two plants in 8 weeks from seed. And I mean, wall to wall, lights pinned at the top and leaves burning because they grow into them anyway. Don't be scared to trim/train a bunch.
  
  
  edit: Last thing. Not an outdoor grower, but in 8 weeks you'll have 4' tall plants that aren't "hardened" to sunlight. That'll be a process. As will supporting the plants. These will likely need trellising straight away.

if they're long shelves most people just get a long hanging thing and put 2-4 T5 bulbs in it.

https://www.amazon.com/4lamps-DL844s-Fluorescent-Hydroponic-Fixture/dp/B00HEYCRI8

This for example. You can get 1,2, or 4 bulb fixtures, and in lengths of 2 or 4 feet. Can find at any big box store, or online for not too bad. then just buy some daylight bulbs for them.

If you want more of a Square format, you can buy 1000-1200 watt LED's that will do a 3x3 or 4x4 foot area for between $40-60.

If you don't have many plants you can always scale down for smaller options in both.

I would think one of these should be pretty good for 40 plants.

https://www.amazon.com/4lamps-DL844s-Fluorescent-Hydroponic-Fixture/dp/B00HEYCRI8/ref=sr_1_1?ie=UTF8&qid=1487633410&sr=8-1&keywords=grow+light+t5

Something like this:

https://www.amazon.com/4lamps-DL844s-Fluorescent-Hydroponic-Fixture/dp/B00HEYCRI8

I like it alright. It's pricier in comparison to the fluorescent lights. I have these two at the moment, though only the latter is in that grow shelf set up:
https://smile.amazon.com/gp/product/B00WDJ7LG2/ (The advantage of this one is that it has two on/off switches so you can control half of the bulbs separately. It also has a power plug that you can plug another light in to.
https://smile.amazon.com/4lamps-DL844s-Fluorescent-Hydroponic-Fixture/dp/B00HEYCRI8 (This one is only two inches tall, so you can fit it into a grow shelf without losing as much headroom. The bulbs are connected by little cords at each end instead of over the top, and it only has one on/off switch and no plugs.

The thing to keep in mind is that the fluorescent lights are all about 1 ft x 4 ft, while the LED light is only 12.6x7.9x3 inches. I could fit three of the LED lights into the same space as one of the fluorescent lights. You can look at that as good or bad, I guess, since it means it's more expensive, but you can also get much brighter coverage over all if you invest in it.

The other thing to keep in mind is that the LED light is fairly loud. The fluorescent light is completely silent, while the LED is louder than a gaming desktop. They can supposedly be modded with quieter cooling fans though, if that matters.

Buy a light, you can screw the first one into any normal lamp or light fixture and this will keep a couple small plants or a whole head of hydroponic lettuce thriving. Or just go huge like me and get the second one. and grow tons of greens.


https://www.amazon.com/gp/product/B00947QMK2/ref=oh_aui_search_detailpage?ie=UTF8&psc=1


https://www.amazon.com/gp/product/B00HEYCRI8/ref=oh_aui_search_detailpage?ie=UTF8&psc=1

How about a frame that easily comes apart?

You can use it at tailgates, camping, or the living room.

https://www.amazon.com/dp/B00LOZNXRC/ref=cm_sw_r_cp_apa_hKuFxbKRHK1FK

I've got the one by "Best Choice" that is a few bucks cheaper but looks to be identical (they even offer the same hammock I got with mine), aside from not having square feet on the bottom of the legs.

I've only used it outdoors a couple of times, but I sleep in it indoors most nights for almost 2 years now and it's never let me down. For outdoors though, I think /u/RecreationalAsshole is on the money with the turtledog stand.

https://www.amazon.com/Best-Choice-Products-Portable-Carrying/dp/B00LOZNXRC/ref=sr_1_4?s=lawn-garden&rps=1&ie=UTF8&qid=1496341476&sr=1-4&refinements=p_85%3A2470955011&th=1

There's a really nice one on Amazon with metal stand. We have two of these in our living room. Only about $60 and a shit load easier than trying to mount into wall studs.

Best Choice Products Double Hammock With Space Saving Steel Stand Includes Portable Carrying Case, Desert Stripe https://www.amazon.com/dp/B00LOZNXRC/ref=cm_sw_r_cp_apa_cP1azbJ3ACJ37

http://www.amazon.com/Best-Choice-Products%C2%AE-Portable-Carrying/dp/B00LOZNXRC/ref=lp_553836_1_3?s=lawn-garden&ie=UTF8&qid=1449855997&sr=1-3

This is the same one in a different color, but only 89$ with free prime shipping. Going to buy myself one soon!

Yo, next time haul this bad boy out and you won't be breaking the rules myguy

https://www.amazon.com/Best-Choice-Products-Portable-Carrying/dp/B00LOZNXRC/ref=sr_1_9?ie=UTF8&qid=1505782931&sr=8-9&keywords=hammock

We use stands like this:
https://www.amazon.com/gp/aw/d/B00LOZNXRC/ref=mp_s_a_1_4?ie=UTF8&qid=1519303216&sr=8-4&pi=AC_SX236_SY340_QL65&keywords=hammock+stand+portable&dpPl=1&dpID=51M4B%2B2xh7L&ref=plSrch

There's a lot of other options out there too, you could even attach between 2 cars if you had your camp set up right!

Being up off the ground helps a lot with the heat, as does not being in an enclosed space. This hammock stand:

https://www.amazon.com/gp/product/B00LOZNXRC/

was fantastic, setup/takedown in five minutes, and I was able to fit it (via the pass-thru) in my two seat convertible.

I might go with a lighter (less warm) hammock next time.

https://www.gemplers.com/product/ARS320/ARS-Grape-Scissors

https://www.ebay.com/itm/Chikamasa-B-500sf-Stainless-Steel-Scissors-w-Fluorine-Coating-Resin-resistant/263795173535?epid=8016915205&hash=item3d6b6ae89f:g:IAQAAOSw7XNbPLH5

https://www.amazon.com/dp/B00P0FK7W6/ref=cm_sw_r_cp_apa_DeANBbJVTGJQ5

Heres what i grabbed except i got the curved and angled blade versions of the first two. Theres lots of other good ones though too im sure. I havent even tried these ones yet though so i cant really recommend them lol its just what i ordered after researching it.

That was my first thought. https://www.amazon.com/dp/B00P0FK7W6/ref=cm_sw_r_cp_awdb_x8S7ybK6PTP7J

Immediately after a full trim (im lazy so I only want to handle and trim my crop one time). Then its on to dry and cure. I have a big 4'x4' oak box I dry in. Its outside on covered patio, I keep a rh meter in it. I have some control over humidity in the box through leaving the lid fully open, slightly open, closed, water bucket... I drop buds in bags and leave open for the 1st day or so (im bud washing so humidity is a little higher than if not washing). I have rh meter in the bag, when it gets down to 60-70 or so I fold over and clip the top closed. I monitor the bags 2,3,4 times a day. Its true, a very important part of the grow is dry/cure. I bet 99% of the crops that get jacked end up worse or trash because the thief does not know how to dry/cure. Good Luck bro/

I use these for bud trimming

https://www.amazon.com/gp/product/B00P0FK7W6/ref=oh_aui_detailpage_o03_s01?ie=UTF8&psc=1

Inkbird thermostat, I figured it would be good enough to use temporarily. I have my other snake on a Herpstat 2 and I intend to use it for the BP too, once she's done with quarantine.

I use this temp gun to check the temps under the hide, at least once a day.

I am a bot programmed to automatically provide the following content by /u/_Ataraxia when summoned. Link to the most recent version of this content here

The first three links are detailed care sheets, then a tub tutorial, and the rest are product recommendations. read everything thoroughly, come back with any questions. Let /u/_Ataraxia know if any of the links don't work.

Glass tanks can be very challenging for ball python husbandry due to the high amount of air flow with the screen top and the total lack of insulation with the glass walls. it's generally recommended to use tubs or pvc reptile cages instead. wood enclosures can also be suitable if they're designed well and sealed properly to protect the wood against moisture. glass tanks can work, but they require a lot of modification and maintenance, which you'll find tips for in the second link. i'll give you product recommendations to cover options for tanks, tubs, and pvc/wood enclosures.

Ball Python Care Guides

• the basics and then some
  
• common problems
  
• feeding problems
  
  Set-up Recommendations
  
  
• here is a tutorial to give you an example of how to set up a tub. this is what i would recommend for an immediate setup, and you could upgrade to a pvc cage upgrade later. note: this tutorial shows adhesive velcro to attach the thermo/hygro to the tub wall, but you should not do that. tape and other sticky adhesives should never be used inside the enclosure, your snake can get stuck on it and suffer serious injuries. hot glue is the easiest reptile-safe adhesive option. screws or bolts can also be used to mount things on plastic/wood walls.
  
• pvc reptile cages are ideal. they have the husbandry benefits of a tub with the aesthetics/visibility of a tank, they're much lighter than wood or glass, and they will remain unaffected by decades of constant high humidity. some popular brands include animal plastics [most recommended], boaphile plastics [i personally have these and like them], reptile basics, and vision cages, though you'll find many more with a quick google search. many people will use a tub at first and upgrade to pvc later.
  
• spyder robotics makes high quality thermostats to regulate your heat sources with pulse/proportional temperature control and various safety features. this is a popular cheap thermostat with simple on/off style with zero safety features. inkbird thermostats are also low-cost but overall higher quality than the hydrofarm type. any heat source should be regulated by a thermostat to ensure safe and appropriate temperatures.
  
• heat tape or ultratherm heat pads are high quality and affordable under tank heater [UTH] options. this is a suitable heat source for most enclosure types. remember that a UTH will not provide ambient heat, it will only affect the temperature of the surface to which it is attached.
  
• a porcelain base lamp and ceramic heat emitter[CHE] is the best ambient heat source for a tank, and it will also work for some pvc/wood enclosures. any heat lamp that emits light, even red or blue, should not be used at night.
  
• a radiant heat panel [RHP] is the best ambient heat source in a pvc/wood enclosure. there are a few options, such as pro products [most recommended] or reptile basics.
  
• a digital dual sensor thermometer/hygrometer allows you to easily monitor the warm side floor temperature [with the probe] as well as the ambient temperature and humidity [with the main unit].
  
• an infrared thermometer allows you to spot-check surface temperatures anywhere in the enclosure.
  
• these hide boxes are a cheap simple hide with a design that offers the best sense of security for your snake. cave style hides, cardboard boxes, plastic food containers, etc, can also be used. half logs are not appropriate hides.
  
  Copypasta version 7/24/2018 (c) /u/_Ataraxia
  
  I am a bot, and this action was performed automatically. Please contact the moderators of this subreddit if you have any questions or concerns.

looks good. if your interested in exploring this type of cooking more but don't want to spring for an anova or other sousvide cooker. use the crockpot method. more precise. and can do longer cooks without losing heat.

basically you hook this
https://www.amazon.com/dp/B015FKG4CC/ref=asc_df_B015FKG4CC5097413/?tag=hyprod-20&creative=395033&creativeASIN=B015FKG4CC&linkCode=df0&hvadid=198107334619&hvpos=1o2&hvnetw=g&hvrand=12722699865548230849&hvpone=&hvptwo=&hvqmt=&hvdev=c&hvdvcmdl=&hvlocint=&hvlocphy=9017523&hvtargid=pla-326308171578

inline with your crockpot. then put the temp probe in the water. bring water up to temp with high once its at temp though switch it to low or warm, otherwise the heater element gets too much momentum during heat cycles and overshoots the temperature. this is what I use currently. i've done 48hr chuck roasts in it and works awesome.

Yeah, I suppose that would work. All you would need then is just a single stage temp controller such as this one:

https://www.amazon.com/dp/B015FKG4CC/ref=asc_df_B015FKG4CC5149652

Haven't grown my koji yet because I'm on vacation, but here's what I purchased and it all works:

​

- Humidistat: https://www.amazon.com/gp/product/B071ND7N8L/ref=oh\_aui\_detailpage\_o00\_s00?ie=UTF8&psc=1

- Perforated pan: https://www.amazon.com/gp/product/B01E95D6H0/ref=oh\_aui\_detailpage\_o02\_s00?ie=UTF8&psc=1

- Pan: https://www.amazon.com/gp/product/B001VZ6Y4O/ref=oh\_aui\_detailpage\_o01\_s00?ie=UTF8&psc=1

- Humidistat: https://www.amazon.com/gp/product/B01J1E5LWM/ref=oh\_aui\_detailpage\_o04\_s00?ie=UTF8&psc=1

- Thermostat: https://www.amazon.com/gp/product/B015FKG4CC/ref=oh\_aui\_detailpage\_o04\_s00?ie=UTF8&psc=1

- Heating pad (I fold it in half): https://www.amazon.com/gp/product/B00P7U259C/ref=oh\_aui\_detailpage\_o04\_s00?ie=UTF8&psc=1

- Styrofoam container: https://www.amazon.com/gp/product/B000NO6F8E/ref=oh\_aui\_detailpage\_o05\_s00?ie=UTF8&psc=1

I installed this controller: Solar Controller, ALLPOWERS... https://www.amazon.ca/dp/B01MU0WMGT?ref=ppx_pop_mob_ap_share

Hopefully that link works. We are in Ontario Canada.

Ah, its pretty important that solar panels get direct sunlight. they get quite a big efficiency loss in the shade.

You would want a solar charge controller, something like this and a solar panel, something like this

The ones I listed are just the first hits on amazon, i dont have experience with those, so do some research :) I think that will work with a motorcycle battery but i might be wrong.

BTW, how about a really long extention cord... like 100ft+?

Post here
https://www.reddit.com/r/vandwellers/
Solar is the standard on vans now. Most people are skipping the engine isolator these days.
You left out the fantastic fan which you'll want if you're doing this level of project.
$700 is way easy. Probably can do for half that. Most people are using $30 MPPT charge controllers for example:
https://smile.amazon.com/ALLPOWERS-Charger-Controller-Intelligent-Regulator/dp/B01MU0WMGT/
Are you putting this on a roof box? otherwise why do you need flexible. Bolt on ridgid panels to a roof rack; cheaper.

Yes! but that's a pretty spendy piece of kit. Wouldn't something like this work sorta the same, just replace the panel input with a 12V source?

It's super bad all around to have your solar panel directly connected to your battery. Probably not too dangerous, but I have heard that the flexible solar panels like to get so hot (if bent in a certain way) that they'll literally burn out parts of them (like a broken fuse).

Main issues here:

1. You're going to over-charge your battery, shortening its life or damaging it.
   
   
2. You're going to be drawing when not charging
   
   I bought one of these guys: https://www.amazon.com/ALLPOWERS-Controller-Battery-Intelligent-Regulator/dp/B01MU0WMGT/ref=pd_lpo_vtph_263_bs_t_1?_encoding=UTF8&psc=1&refRID=XPGVMHDYZV5TBJ2NCJ53
   
   You can go much more expensive, but it's not really worth it. Worst thing that happens to these is they stop working. If you're really worried about that, buy a spare or two.
   
   20A is more than enough for anything less than 200W. If you have more than 200W of solar panel you'll need more.
   
   My 100W setup is larger than your flexible (lower efficiency) panel, and peak I'd only output a little more than 8 amps.
   
   Your solar panel might also be bad. Check how many amps its outputting. You need a cheap multimeter for this kind of work.

[inverter](ampeak 1000w power inverter 12v dc to 110v ac dual ac outlets 2.1a usb car inverter https://www.amazon.com/dp/B071NZ8DSB/ref=cm_sw_r_cp_apa_i_NbC6Ab814KH3Z)
[solar controller](allpowers 20a solar charger controller solar panel battery intelligent regulator with usb port display 12v/24v https://www.amazon.com/dp/B01MU0WMGT/ref=cm_sw_r_cp_apa_i_adC6Ab4DAFH9X)
And ill add some sort of solar panel

$100 panels https://www.amazon.com/gp/aw/d/B01HHDC6NQ/

$20 charge controller https://www.amazon.com/gp/aw/d/B01MU0WMGT/

$100 marine battery https://www.amazon.com/gp/aw/d/B008974VFG/

$150 ac inverter 2000watt https://www.amazon.com/gp/aw/d/B0716WT8D5/

https://www.amazon.com/gp/aw/d/B01MU0WMGT/ref=mp_s_a_1_3?ie=UTF8&qid=1495807720&sr=8-3&pi=AC_SX236_SY340_FMwebp_QL65&keywords=Solar+controller

I used 2 solar panels, 2 deep cycle batteries and this solar charger off Amazon

https://www.amazon.com/gp/aw/d/B01MU0WMGT

I have this one right now https://www.amazon.com/gp/product/B01MU0WMGT/ref=ppx_yo_dt_b_asin_title_o03_s00?ie=UTF8&psc=1

but I could be putting up 50 of these configurations and need a way to get the data remote without traveling to check the controller

I'm relatively new to succulents and I'm looking for any feedback on my overwintering setup. I have limited space, so this is what I came up with..

http://imgur.com/gallery/QjJMM1C

Edit: this is the light I have
https://www.amazon.com/dp/B0748D2SMB/ref=cm_sw_r_cp_apa_Aj-XBbAJNCS9T

I've seen both of these recommended here:

https://www.amazon.com/dp/B0748D2SMB/?coliid=IV20LOG462GWX&colid=3Q2ZGS49DRJ7A&psc=0&ref_=lv_ov_lig_dp_it

https://www.amazon.com/dp/B01B4GQ6MO/?coliid=I7599APCLG2TG&colid=3Q2ZGS49DRJ7A&psc=0&ref_=lv_ov_lig_dp_it

These are probably overkill for a 5 gal, these are what I use on my 30 gal. You'll need a lamp or a waterproof socket. They make a vert bright purple light, which is optimal for plant growth. You get less algae than from a white light.

https://www.amazon.com/TaoTronics-Spectrum-Hydroponics-Organic-Wavelengths/dp/B0748D2SMB/ref=sr_1_6?ie=UTF8&qid=1539504329&sr=8-6&keywords=e26+led+grow+light

​

If you want white light, google "high cri led par"

cri - color rating index. Basically, how well does a LED replicate the color of an incandescent bulb. I look for over 90cri

par - describes the lamp shape. Directs all the light forward in a wide cone, great for overhead lighting on a tank because a single lamp's light will spread out to cover the whole tank, and the bright lens of the bulb is pointed away from your eyes. For choosing your wattage, you'd probably want something in the 10-15W range.

Also, choose one that is 3000K. This replicates the warm amber color of an incandescent bulb. The higher the K, the more blue the light. Plants need mostly red light, and a bit of blue. It's also easier on the eyes, and I know how much time we all spend staring into our tanks.

​

​

this is what I’ve been using!

I started using 6 of these, but you might be able to start with 4 and supplement with some CFL.

https://www.amazon.com/TaoTronics-Spectrum-Hydroponics-Organic-Wavelengths/dp/B0748D2SMB

LED Grow Light Bulb, TaoTronics Full Spectrum Grow Lights for Indoor Plants, Grow Lamp, Plant Lights for Hydroponics, Organic Soil (36W, All Wavelengths, FREE E26 Socket) https://www.amazon.com/dp/B0748D2SMB/ref=cm_sw_r_cp_apa_i_wUuPCbYF3BR55

I use these. https://www.amazon.com/dp/B0748D2SMB?aaxitk=1Jl64k8F2dJkCEbIEo-62Q&th=1&psc=1

Plants are growing great with them, no complaints. (Actually, my only complaint is that they take a few minutes to turn on again after switching them off for some reason.)

Thank you so much! Here is the link to the one that I purchased. I have it about 2 feet above my succs and I keep it on 24/7. Grow Light

I have one of these. You can put it in any standard E26 socket (that's the usual light bulb socket). The bulb looks kinda neat and the light color is slightly pink instead of shocking magenta so it's not obnoxious. Also, it provides enough light to actually grow some things. I currently have tomato starts under it and they're doing fine.

I have 4 led grow lights https://www.amazon.com/gp/product/B0748D2SMB/ref=oh_aui_detailpage_o03_s00?ie=UTF8&psc=1 I think i turned some off when i took this picture.

Thanks, I picked [this one](Sonkir Soil pH Meter, MS02 3-in-1 Soil Moisture/Light/pH Tester Gardening Tool Kits for Plant Care, Great for Garden, Lawn, Farm, Indoor & Outdoor Use (Green) https://www.amazon.com/dp/B07BR52P26/ref=cm_sw_r_cp_apa_i_Ep5pDb3T1PGV9) so hopefully that does everything I need it to

I don't know, mine works very well. Maybe yours is broken?

Sorry, on my phone but I have this one: Sonkir Soil pH Meter, MS02 3-in-1 Soil Moisture/Light/pH Tester Gardening Tool Kits for Plant Care, Great for Garden, Lawn, Farm, Indoor & Outdoor Use (Green) https://smile.amazon.com/dp/B07BR52P26/ref=cm_sw_r_cp_apa_i_KP-wDbHT4Q2K7

Here is what I am using.

​

Filter w/ fan : https://www.amazon.com/VIVOSUN-Inline-Control-Australia-Charcoal/dp/B01MSEVQ3J/ref=sr_1_4?s=hi&ie=UTF8&qid=1539056270&sr=1-4&keywords=vivosun+4+inch

​

I also bought some MDF board, and built a box for the fan to go into. It was a little louder than I wanted it to be, so now it's really quite. I will add a picture for you to check it out.

​

Tent: https://www.amazon.com/gp/product/B01JN8REQC/ref=oh_aui_detailpage_o01_s00?ie=UTF8&psc=1

​

I got one of these things: https://www.amazon.com/gp/product/B07BR52P26/ref=oh_aui_detailpage_o01_s00?ie=UTF8&psc=1

​

​

Do you have a recommended soil sample kit? I've seen some probes like this ( https://www.amazon.com/Sonkir-Soil-Moisture-Tester-Gardening/dp/B07BR52P26/ref=sr_1_8?crid=YY2LFNJIJM8F&keywords=soil+sample+test+kit&qid=1558203214&s=gateway&sprefix=soil+sample%2Caps%2C156&sr=8-8 ) but I'm highly skeptical of them for some reason.

Not using the smart meters for moisture, just light. Using this for moisture

https://www.amazon.com/dp/B07BR52P26/ref=cm_sw_r_fm_apa_i_wrmMDbYKEC1AJ

A $210 pH meter strikes me as an extravagance for this level of grow. You can use pH strips or better off, use a small standard soil pH tester.

The 4 inch carbon filter will work, but it's going to need an inline fan and some ducting hose.

Personally, I'd just get a small grow tent that fits the dimensions of your closet, and scrap the mylar and poly film. Then you can duct the fan and filter directly into your tent.

The tent only needs to be about 3 or 4 feet tall. You can place it on a table or stand if you want. Then you can sit in a chair when you tend your plants.

Some sort of adjustable rope system to hang the lamps.

I've grown more than a dozen crops indoors, and I've never worried about adding CO2 to the grow space. I'm aware of the benefits, but this might be more of an advanced consideration. If you're looking to economize, this would be one thing I think you could definitely cut for at least the first few grows.

One thing that could benefit you might be Marijuana Horticulture by Jorge Cervantes. He's been updating and revising this book for 35 years. So it's pretty comprehensive, and it can take you from first grow all the way up to how to grow top shelf bud. It will tell you exactly what soil and nutrients you need, which can save you a lot of money versus overpriced fancy boutique nutrients and designer potting soils. And it can help you troubleshoot the inevitable problems when they occur.

>How deep down do you let it get dry? How are you determining that it's dry? Eyeballing the top, or sticking your finger into it?

I have a combination PH and wetness tester. I usually eyeball it, but I check the moisture with that if I'm not sure.

>Is there a hole in the bottom of the planter?

Yes

>Your soil can't possibly be pH of 1-2. What acidic thing have you been adding that would have dropped the pH that low? Test the tester on ordinary tap water. It should be 7.

I will try this - thanks.

>Stop adding lime, it's for agriculture outdoors, where the vastly larger volume of soil, plus processes of soil chemistry and weather, work to ameliorate and regulate its effects. It's not for planters, where it can quickly and catastrophically raise your pH to Stephen King Dead Zone levels. Is that the white stuff sprinkled on top? Did the pepper that's wilted start wilting after you sprinkled lime all over the soil?

Yes - the white stuff is the lime. I mixed it with water and poured it over both plants twice over a month or two. Like I said in the original post, one of the plants exploded and started doing fantastically when I added the lime, but the other one started looking like this. They're in the exact same planter, so I'm confused why it hurt one and helped the other. I'll cut out the lime though. Any recommendations on how to help the droopy plant at this point?

Alibaba for sure.

If you're stuck on not ordering from alibaba, spend more and get an HLG 100 off Amazon for 149, or just get unstuck and order from alibaba.

https://www.amazon.com/Horticulture-Lighting-Group-USA-Quantum/dp/B07C57J7XX/ref=asc_df_B07C57J7XX/?tag=hyprod-20&linkCode=df0&hvadid=241883109355&hvpos=1o1&hvnetw=g&hvrand=8474130366492575844&hvpone=&hvptwo=&hvqmt=&hvdev=c&hvdvcmdl=&hvlocint=&hvlocphy=1016441&hvtargid=pla-443916306627&psc=1

That's 25 bucks more for a way better light than that roleadro trash. Don't get lost in the wattage numbers. Blurple watts are bullshit.

Spend the price of a few joints extra and get a better light (HLG)

i am considering these

https://www.amazon.com/Quantum-Board-Grow-Bloom-4000K/dp/B076QDKVDZ

https://www.amazon.com/Horticulture-Lighting-Group-USA-Quantum/dp/B07C57J7XX


my tent is 2x4 and 5ft high. The first one is probably too small? Would the second suffice?

https://www.amazon.com/Horticulture-Lighting-Group-USA-Quantum/dp/B07C57J7XX?ref_=ast_sto_dp

would do you well in that space. It's just at the upper end of your price limit. ($150)

Super simple to put together

So something like this would be ideal for what i'm looking for? :)

Check out EveryThang on YouTube, he has videos on the lights he uses and how echeveria color works.

Grow lights have been a chore to shop for, there are so many variations and the made in china stuff has a wide mix of reviews. The purple ones hurt my eyes (if you have thick or cheap glasses they will be extra bad- double vision), so shopping for white... I’m leaning towards a Sunblaster LED, if I can find one.
They also depend on your setup- can you hang a 4’ tube above your plants? An 18” tube? A single bulb? A clip light? A monster unit with cooling fans built in?
I have a Kingbo 50W led dual-head that stopped etoliation on an echeveria elegans (https://smile.amazon.com/gp/aw/d/B07LG39B3M?psc=1&ref=ppx_pop_mob_b_asin_title) but I’m not sure it’s enough to maintain color. Mine is on for 14 hours in a sunny window and my black prince is only green-blackish, so probably not.
Time of the light depends on how strong and how far away it is.

Its just a little LED light

https://www.amazon.com/KINGBO-Spectrum-Gooseneck-2-Switch-Replaceable/dp/B07LG39B3M?ref_=Oct_CARAsinC_14252941_3&pf_rd_p=bf98d1fc-853a-5849-80d4-b55241de1a6a&pf_rd_s=mobile-hybrid-5&pf_rd_t=30901&pf_rd_i=14252941&pf_rd_m=ATVPDKIKX0DER&pf_rd_r=TS5NP0D8Y3B9QJ44NH4K&pf_rd_r=TS5NP0D8Y3B9QJ44NH4K&pf_rd_p=bf98d1fc-853a-5849-80d4-b55241de1a6a

Typically nepenthes aren’t too picky on lighting but a cheap grow light I love(mainly for the low price and simplicity) is the Acke grow light https://www.amazon.com/ACKE-Germination-Seedling-Vegetative-Flowering/dp/B07GGX3R9T/ref=asc_df_B07GGX3R9T/?tag=hyprod-20&linkCode=df0&hvadid=242081228138&hvpos=1o3&hvnetw=g&hvrand=9594542324276355578&hvpone=&hvptwo=&hvqmt=&hvdev=m&hvdvcmdl=&hvlocint=&hvlocphy=9022987&hvtargid=pla-533179316540&psc=1
That’s the “normal light” version, there’s another one that’s super pink. I haven’t noticed much difference in the effectiveness of either.

This is the exact light that I got here:

https://www.amazon.com/gp/product/B07LG39B3M/ref=ppx_yo_dt_b_asin_title_o08_s00?ie=UTF8&psc=1

It had a lot of good reviews, and it seemed pretty close to sunlight. So far I think my herbs are doing quite well (my cilantro and dill have really taken off) but I would absolutely love trying to grow fruiting plants like tomatoes or peppers inside if it's at all possible. I live in an apartment in Minnesota with no balcony, so I'd really love to find a good alternative to a yard! :)

I'd love to have a link to your YouTube channel, if you wouldn't mind sending it to me.

The moisture seems to do alright spreading without the fan. I don't think you would necessarily need it. I use it to increase air flow in order to prevent algae from taking over the tops of the soil on my plants in there and possible mold.

You might want to ask more about lighting from r/mosses since they're better equipped to discuss moss needs than I am. I know that my moss has been fine with this (https://www.amazon.com/gp/aw/d/B07LG39B3M?psc=1&ref=ppx_pop_mob_b_asin_title) placed about 10 inches from the moss and turned on for 10 hours a day. But, I have no clue if that's optimal, I just know it works for me.

I currently have a dieffenbachia, peace lily, bromeliads and croton. I’ll use the light for the croton, dieffenbachia and peace lily. I’m considering this light: https://www.amazon.com/dp/B07LG39B3M/ref=psdc_14252941_t1_B07Q4RQ4V6

Thanks!!!

I got them both on amazon! The top lights are: KINGBO Newest 50W Led Grow Light Bulb for Indoor Plants, Super Bright 100 LEDs Sunlike Full Spectrum Grow Lamp White, Dual Head Gooseneck Desk Plant Light with 2-Switch, Replaceable Bulb (2019 Update) https://www.amazon.com/gp/aw/d/B07LG39B3M/ref=ya_aw_oh_bia_dp?ie=UTF8&psc=1#

The purple lights are: from Brite labs and have a timer with adjustable light intensities
https://www.amazon.com/Brite-Labs/b/ref=bl_dp_s_mw_19491218011?ie=UTF8&node=19491218011&field-lbr_brands_browse-bin=Brite+Labs

Happy planting! 💜

https://www.amazon.com/dp/B07LG39B3M?ref=ppx_pop_mob_ap_share
It’s only 30 for the one I got and it’s really bright

Yes and it’s a little oscillating desk top tower fan hooked up with my timer. These are the lights https://www.amazon.com/dp/B07LG39B3M/ref=cm_sw_r_cp_api_i_-vsQCbE1TJ63M.

Appreciate the advice. I found this on amazon: https://www.amazon.com/KINGBO-Spectrum-Gooseneck-2-Switch-Replaceable/dp/B07LG39B3M/ref=mp_s_a_1_6?keywords=plant+light&qid=1556394641&s=gateway&sr=8-6

Someone in a review has their Heliamphoras and Sundews under it and said they were thriving. Not sure if this would work.

In Canada it's also on sale ($390 CAD - $25 coupon), but not as nearly as good as US sale - https://www.amazon.ca/Jackery-Portable-Power-Station-Generator/dp/B07D29QNMJ/ref=as_li_ss_tl?ref_

amazon.COM doesn't ship this product to Canada, at least to my location anyways...

That light is garbage, do not buy it. If you need a cheap grow light get a Viparspectra 300 or 600. They are reliable lights that last a long time. However, your money will be better spent on a high quality light, quantum boards are currently the best commercially available to home growers: https://horticulturelightinggroup.com/products/hlg-100

That’s a great price on an all in one light that will last basically forever. There are others manufacturing these types of boards for lower cost but you would have to do some research and building. The HLG kits can be purchased on Amazon HLG 100 V2 4000K Horticulture Lighting Group Quantum Board LED Grow Light Veg & Bloom | Version 2 High-Efficiency Upgraded LM301B LED's- Includes Radix 100ml https://www.amazon.com/dp/B07C57J7XX/ref=cm_sw_r_cp_api_i_39Q2DbP5CP9SD

I've been using 2 of these the 4k version https://www.amazon.com/Horticulture-Lighting-Group-USA-Quantum/dp/B07C57J7XX for the last 8 weeks and I've never had buds this dense before. If I was you I would just buy one of these for a 2x2.

I see your point. I like the option but here is a question..

Say I buy this: https://www.amazon.com/Horticulture-Lighting-Group-USA-Quantum/dp/B07C57J7XX

Like you are saying its $150. and its supposed to be as effective as a 300w cfl.

It consumes the same amount of energy as say this: https://www.amazon.com/VIPARSPECTRA-Reflector-Spectrum-Indoor-Plants/dp/B01B4GQ6MO/ref=sr_1_3?keywords=Viparspectra&qid=1555016528&s=lawn-garden&sr=1-3

Which is also supposed to be as effective as a 300w lamp...

Whats the reason behind spending double if I am not gaining anything on performance or efficiency? The one advantage I see is no pink light.

If you have 200$ to spend, get a quantum board. It will outperform blurple light

https://www.amazon.com/Horticulture-Lighting-Group-USA-Quantum/dp/B07C57J7XX/ref=mp_s_a_1_2?keywords=hlg+qb&qid=1556636878&s=gateway&sr=8-2

Do yourself a favor and stick with quality QB! The HLGs are fucking amazing. for a 2x2 their 100w board is perfect for flower, and only $150. You can get them in 3000k or 4000k. I have a 550 covering my 4x4 and 3 of the HLG65s covering two smaller tents (2x3 and 2x2)

These

https://www.amazon.com/Jackery-Portable-Power-Station-Generator/dp/B07D29QNMJ/ref=asc_df_B07D29QNMJ/?tag=hyprod-20&linkCode=df0&hvadid=241946544904&hvpos=1o4&hvnetw=g&hvrand=4012940401562641907&hvpone=&hvptwo=&hvqmt=&hvdev=c&hvdvcmdl=&hvlocint=&hvlocphy=9032925&hvtargid=pla-473476596395&psc=1
Something like that? I always just suggest not spending anything to do with charging limes, thats just a cost youll need to recoup before making profit.

Jackery Portable Power Station Explorer 240, 240Wh Emergency Backup Lithium Battery, 110V/200W Pure Sinewave AC Outlet, Solar Generator for Outdoors Camping Travel Fishing Hunting https://www.amazon.com/dp/B07D29QNMJ/ref=cm_sw_r_cp_api_i_BcwgDbK965KGJ

And

Renogy 100 Watt 12 Volt Monocrystalline Off Grid Portable Foldable 2Pcs 50W Solar Panel Suitcase Built-in Kickstand with Waterproof 20A Charger Controller https://www.amazon.com/dp/B079JVBVL3/ref=cm_sw_r_cp_api_i_edwgDbCSDQG23

I apologize,I had been thinking of something like the Jackery Portable Power Station Explorer 240 which I misremember as 240 amp hours rather than 240 watt hours. They also make a 500 watt hour model for ~500 dollars. That’s probably two recharges a day for most mini fridges with the 240.

I did find this fridge the Ausranvik Car Fridge Portable Freezer which uses 32watts DC when it runs apparently (and won’t run all the time) so except in the hottest weather it should keep you on once a day recharge, or a few days with a big block of ice.

You could also lean on friends in the dorms to keep a big jug of water in a communal freezer for you and swap it out every few days.

I use 20w LED lights. Specifically this model:

ACKE LED Grow Light for Indoor Plants,Plant Light for Grow Light Stand,DIY Indoor Growing Light Panel for Germination,Seedling,Vegetative Growth and Flowering https://www.amazon.com/dp/B07GGX3R9T/ref=cm_sw_r_cp_api_i_daXOCb4WJYD91

I switched to LED from fluorescent this year. If you use fluorescent you need to move them to be about 3 inches from the tallest plant so they don’t burnt on the bulb.

With my LED lights I have the plants up to 1 foot away and they aren’t stretching for the light because they offer great lighting for plants.

Does that help? If you like you can check out my channel for a bunch more of pepper related stuff:

www.youtube.com/c/farmergeorge

Let’s Share and Grow Together :)

Thank you so much for your detailed reply!! I really appreciate it.

So I went ahead and got an electricity usage meter so that I can see how much power the devices I plan on taking with me will use. Like you said, this will allow me to better plan my setup. I should have done this first actually.

Another setup I'm considering is a power generator similar to something like this. What I'd like though is that it has 2 inputs for charging: one from the car and one from the solar panel. I don't want to be having to change inputs when I drive, and then change it again when I'm stopped. Most of the power generators/stations I've seen only have one DC input though. I tried looking for a male to female DC splitter but the ones I've found I don't think are strong enough to run the current from the two charging sources simultaneously.. the only one on Amazon I found is 22 AWG, which according to wikipedia can handle at most 6-7 amps. Did I understand that correctly? Does a DC splitter with a lower AWG even exist?

Another feature I'd like is the ability to use the generator while it's charging, but unfortunately even here most of the units I've seen cannot do this.

I'm going to wait till I have a better idea of the max amount of power I'll need before I research this again.

Thanks for the advice on how to run the fridge efficiently btw. I didn't even consider this. Those are excellent points. Also your idea on the passive water supply for the evap cooler, that's brilliant! I'm going to try fitting that into my design. And I say this bc it can't be that big, but I can perhaps have a half a gallon bottle..

How is that on battery life of car? If I used it 3> hours should it be fine? I was looking at portable charging stations, how would those work in a vehicle? Ex: power station

Could look into getting something like this. But the insulated pump thermoses are pretty awesome, too.

I found this pump.


12V - 24V DC Brushless Submersible Water Pump, 410GPH, for Solar Fountain, Fish Pond, and Aquarium (1 Pack) https://www.amazon.com/dp/B01IAFCRF2/ref=cm_sw_r_cp_apa_i_klPUCbC8654GZ



Could I connect a panel and the pump to something like this?
Jackery Generator Portable Power Station Explorer 240, 240Wh Emergency Backup Lithium Battery, 110V/200W Pure Sinewave AC Outlet,Solar Generator for Outdoors Camping Travel Fishing Hunting https://www.amazon.com/dp/B07D29QNMJ/ref=cm_sw_r_cp_apa_i_JnPUCb71XRWR7

not sure what the recharge rate is but i would imagine unless your directly tethering to the terminals then you would be limited to the fuse amperage, typically like 15 amps on a cigarette plug i think?


back on the main topic, maybe something in this article might help? https://teslatap.com/articles/12-volt-battery-compendium/ they dont mention exact rates that i saw but it says "

>The Gen 2 DC-DC converter in the refreshed Model S accepts 220 to 430 VDC at 15 amps, and outputs 9 to 16 VDC. When outputting 12 VDC, it can deliver about 200 amps.
>
>The Model 3 integrates the charger and the DC-DC converter into a single package, the PCS (Power Conversion System)

​

IMHO i would just invest in one of those Portable power stations from the likes of Jackery, Anker or Goal Zero especially seeing as how the replacement battery is going for about $500 on Amazon.

I got this very low profile grow light from Amazon it says 20watts

ACKE LED Grow Light for Indoor Plants,Plant Light for Grow Light Stand,DIY Indoor Growing Light Panel for Germination,Seedling,Vegetative Growth and Flowering https://www.amazon.com/dp/B07GGX3R9T/ref=cm_sw_r_cp_apa_i_JgfxDbDCBNXN9

I have this light hanging from a shelf that I use for growing basil indoors: ACKE LED Grow Light for Indoor Plants,Plant Light for Grow Light Stand,DIY Indoor Growing Light Panel for Germination,Seedling,Vegetative Growth and Flowering

https://www.amazon.com/ACKE-Germination-Seedling-Vegetative-Flowering/dp/B07GGX3R9T

You can configure it lengthwise instead of how it’s shown in the picture. And I think you can connect two set together, but don’t know that for sure.

It’s a warm white light which is accomplished by having white and red LEDs

Edit: link

I've had good luck with this one

A small 20watt LED panel, but one that's NOT blurple since it's on all the time in a living area of the house and I really didn't want to deal with a pink glow in my kitchen all the time.

This is the one I got.
https://www.amazon.com/dp/B07GGX3R9T/ref=cm_sw_r_em_apa_i_3FkNDb82DW4C7

ACKE LED Grow Light for Indoor Plants,Plant Light for Grow Light Stand,DIY Indoor Growing Light Panel for Germination,Seedling,Vegetative Growth and Flowering https://www.amazon.com/dp/B07GGX3R9T/ref=cm_sw_r_cp_api_i_p3LYDbDX85QCH

These would work great with your table!!

Got that covered, I have a larger, better 24v MPPT on the way. However, I have to disagree. ut the spec sheet says 24v (https://www.amazon.com/ALLPOWERS-Charger-Controller-Intelligent-Regulator/dp/B01MU0WMGT/ref=pd_lpo_vtph_263_bs_t_1?_encoding=UTF8&psc=1&refRID=TAP7B6HN0BP9SXXHVYN8)

https://www.amazon.com/Chapin-International-617407731200-20002-Multi-Purpose/dp/B0039EEN0M/ref=sr_1_36?gclid=Cj0KCQjws7TqBRDgARIsAAHLHP5v1xtproNTHroGCwFmUuxCfaRRo2d5RnUprmrf4zU9xmcQVRmhL20aAu58EALw_wcB&hvadid=174205407345&hvdev=c&hvlocphy=9004392&hvnetw=g&hvpos=1t2&hvqmt=e&hvrand=4809304190223278778&hvtargid=kwd-4982744865&hydadcr=24630_9648900&keywords=commercial+spray+bottles&qid=1565346758&s=gateway&sr=8-36

She sick, not sure what she needs.
Also, I don't have $ to buy shit to fix it so she probably going to die :'(
She was doing well up to the last two watering, the first one I saw a little discoloration and then I didn't gave her any nutrients and molasses and just PH'd water at 6.5 but she became worst... the discoloration worsened ..

If I buy those two or three products will she survive ?
Cal-mag but from another brand and some blooming nutrient ?
https://www.amazon.ca/gp/product/B00GZRKI40/ref=ox_sc_act_title_2?smid=A1XUOM4FC8JNBK&psc=1
https://www.amazon.ca/dp/B00BYG6TIG/ref=wl_it_dp_o_pC_nS_ttl?_encoding=UTF8&colid=1J77SE4LW6ZXQ&coliid=I6RRMFYCDMZMV&psc=1
https://www.amazon.ca/dp/B00BYG6P0I/ref=wl_it_dp_o_pC_nS_ttl?_encoding=UTF8&colid=1J77SE4LW6ZXQ&coliid=I1AU019W83GWHZ&psc=1

If anyone feels generous : https://www.amazon.ca/gp/registry/wishlist/1J77SE4LW6ZXQ/ref=nav_wishlist_lists_2

• Strain : Northern Light
  
• Vegetation State : 80
  
• Flowering State : 14 Days
  
• Earth : Pro-Mix ORGANIC VEGETABLE & HERB MIX Mycoactive Compost + Cow Manure
  
• Light : Mars Hydro 300W LED Grow Light (135W±10% True Watt)
  
• Tent : Mars Hydro 27"x27"x63" Grow Tent
  
• Pot : 4 1/2 Gal with a over watering reservoir build in the bottom
  
• Nutrient : Miracle Grow + Molasses
  
• Timing : 18/6 Veg now in 12/12 Flowering
  
• Temp & Humidity : 30° to 34° & 15% to 20%
  
• Technique used : Lollipopping, LST, Topped, SCROG